S9300 登陆软件问题导致启动不正常

发布时间:  2014-12-28 浏览次数:  106 下载次数:  0
问题描述
新购买的9306交换机设备,无法开机。
CFM_Init begin..........   
启动时到这里就停止了,一直不动
点回车后就是下面提示:
An initial password is required for the first login via the
Set a password and keep it safe! Otherwise you will not be a
Set a password and keep it safe! Otherwise you will not be a
An initial password is required for the first login via the
Set a password and keep it safe! Otherwise you will not be a
An initial password is required for the first login via the


使用CRT 软件登陆
告警信息
Bootrom Version ......................................................................................................OK
BIOS Creation Date ...................................... Oct 21 2011, 09:47:36
BoardType is...............................
DDR DRAM init................................................................OK
Start Memory Test ? ('t' or 'T' is test):skip
Copying Uncompressed Data from Rom to Ram ..............Done
Uncompressing Data from Rom to RAM .....................Done
Initializing Flash Module .............................
Initializing Flash Module .................................Initializing LanSwitch .......................................................Done
Intilalizing Port 1 MAC:d4-6a-a8-79-f2-70 .................................Done
Intilalizing the Debug Port................................................Done
Attached TCP/IP interface to eth unit 1....................................Done
Attaching network interface lo0............................................Done
Load Network Protoc

     ****************************************************
     *                                                  * ****************************************************
    Copyright(C) 2003-2011 by HUAWEI TECHNOLOGIES CO., LTD.
    Creation date: May 31 2012, 13:46:50
    PCB Version     : LE02SRUA VER.D
    CPU L2 Cache    : 128KB
    CPU Clock Speed : 700MHz
    BUS Clock Speed : 133MHz
    Memory Type     : DDR2 SDRAM
    Memory Size     : 1024MB
    Memory Speed  
CF Card Init............................................. 0
Backplane information: 0x15Auto-booting...
write ulStartupTime to Nvram......ok
write ulStartupTime to flash.ok
ulStartupTime = 0x1
Booting from CFCard[cfcard:/S9300-V2
Vxworks Creation Date ....................................Jul 31 2012, 10:50:46
Initializing Flash Module..............
Intilalizing Port 0 MAC:d4-6a-a8-79-f2-71 .................
Intilalizing Port 1 MAC:d4-6a-a8-79-f2-70 .................Intilalizing FSU PHY .........................................
Product Type...............................................
CF Card Init...............................................Initializing LanSwitch .......................................
Epld  test .......................................... pass.
Nvram AddressBus test ................................pass.
Battery  test ........................................pass.
LanSwitch  test ......................................pass.
THE PHY(0)  test .....................................pass.
THE PHY(1)  test .....................................pass.
THE PHY(2)  test .....................................pass.s is commercial software; see the source for copying conditions.
There is NO warranty; not even for MERCHANTABILITY or FI
Css Enable.....................................................................0
Frame CSS Role................................................................NO
Self Local SlotId..............................................................7
Self Global SlotId.............................................................7
Peer Local SlotId..............................................................8
Peer Global SlotId.............................................................8
BOARD ROLE................................................................MASTER
SET INTR HOOK.......................
Init system resource mode from flash: 0
DEV_CreateMpuHigi
Drv_Rcv_Reg OK!
VOS_Start begin ...
Board_InstallDrv OK
CSSFU_Global_Init g_ulCSSFUpgradeFlag: 4294967295
CSS COMPETITION...............................................ONE
CSS ROLE.......................................................................0
CSS SYSTEM MASTER..............................................................7
CSS SYSTEM SLA
Init gtlv1 nvram data.......................OK
Init gtlv2
Get product key.............................OK
Try to get self esn.........................0
Get esn from backplane......................OK
Get self esn.........................OK
Adapt function for GTLV2....................OK
VRP_Root begin...
VRP_InitializeTask begin...
Init the DevicCFG_PlaneInit begin..............OK
CFM_Init begin..........    都是这里就停止了 
点回车后就是下面提示
An initial password is required for the first login via the
Set a password and keep it safe! Otherwise you will not be a
Set a password and keep it safe! Otherwise you will not be a
An initial password is required for the first login via the
Set a password and keep it safe! Otherwise you will not be a
An initial password is required for the first login via the
处理过程
第一次启动要设置一个初始密码。
怀疑串口线或者终端软件的串口配置有问题。输出的信息换行和回车信息比较混乱。
解决方案


把流控RTS/CTS勾去掉后测试正常
建议与总结
此问题会误认为是设备软件问题,但实际上却是登陆软件设置问题,所以可以注意下

END