关于PTN910 CXPG主控板使用脚本设置带宽利用率门限显示不一致问题

发布时间:  2012-09-28 浏览次数:  81 下载次数:  0
问题描述
    根据公司“OptiX PTN产品 关于需要合理设置带宽利用率门限的公告-20120820-A”文档要求,某地市移动PTN网络需要全网修改PTN产品FLOW_OVER告警门限值,设置低门限75%,高门限85%,PTN主机版本均为刚升级的1731版本SPC600,根据文档配置好脚本以后,执行成功,单检查过程中,发现PTN3900、PTN950所有端口都能设置成功,而PTN910设备CXPG主控板均设置不成功,显示“不一致”。如下图:






处理过程
1、脚本配置错误
2、执行不成功
3、查询显示不正确

根因

910主控板有一部分E1端口,按板级查看存在E1端口与ETH端口告警门限不一致现象,但ETH端口查看即可。

解决方案
1、通过分析脚本,未见异常,PTN910主机版本是V100R002C01SPC600,也符合脚本要求主机版本;重新单独找一个PTN3900网关网元,下挂2台PTN910,重新执行脚本,脚本执行成功,故障依旧,PTN910 CXPG门限值依旧显示不一致
2、经过定位,检查脚本执行的Navigator的日志文件,确认了原因。PTN910 CXPG实际上是已经修改成功了的,由于CXPG板较特殊,其中1-16口是E1口,17-18是GE口,19-22是FE口,实际上报错的是1-16口,实际上1-16口并未在脚本中设置修改,而17-22口是设置成功了的,检查的时候需要在RMON设置中只选择CXPG对应的端口查看即可,查看方式见下截图:



原来的脚本继续执行,脚本无问题

#71-3098:szhw [3098-南宁邕宁区荣裕盛昌专线                                     ][][2012-09-18 14:58:49+08:00]>
:perdata-cfg-get-tr:pmall,0xff,ethport,0,"board=2,subcard=0xff,port=17"
                                                         DATA  PER  ALM  THRESHOLD                                                                                                                                                                                                                                                                                                                                                               
  EID                         htr1        htr0        ltr1        ltr0        RESERVED  OBJTYPE                            OBJLEN  OBJPARA                                                                                                                                                                                                                                                                                                       
  rxoctets                    0           10000000    0           7500000     0xff      ethport                            0x001b  board=2,subcard=255,port=17                                                                                                                                                                                                                                                                                   
  port_rx_bw_utilization      0           8500        0           7500        0xff      ethport                            0x001b  board=2,subcard=255,port=17                                                                                                                                                                                                                                                                                   
  port_tx_bw_utilization      0           8500        0           7500        0xff      ethport                            0x001b  board=2,subcard=255,port=17                                                                                                                                                                                                                                                                                   
  Total records :3                                                                                                                                                                                                                                                                                                                                                                                                                                            



建议与总结


END