選択した言語が見つかりません。

このサイトはCookieを使用しています。 サイトを閲覧し続けることで、Cookieの使用に同意したものとみなされます。プライバシーポリシーを読む>

RH2288 V3 Server V100R003 User Guide 29

Rate and give feedback :
この文書の日本語を含む他言語への翻訳は、元の文書の内容の理解を支援する目的で提供されています。翻訳には機械翻訳が利用され、人間による簡単な校正のみが行われています。 注: 最先端の機械翻訳を利用した場合でも、翻訳の品質はプロの翻訳者による翻訳ほど十分ではありません。ファーウェイは、翻訳の正確性についていかなる責任も負わないものとします。リンクを使用して、英語版の元の文書も同時に参照することを推奨します。
About This Document

About This Document

Purpose

This document describes the appearance, features, and specifications of the RH2288 V3 and explains how to install and remove the server and its parts, power on and off, configure, and troubleshoot the server.

Read this document before operating the RH2288 V3.

Intended Audience

This document is intended for:

  • Technical support engineers
  • Maintenance engineers

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol

Description

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results.

NOTICE is used to address practices not related to personal injury.

Calls attention to important information, best practices and tips.

NOTE is used to address information not related to personal injury, equipment damage, and environment deterioration.

Change History

Changes between document issues are cumulative. The latest document issue contains all changes made in previous issues.

Issue

Date

Description

29

2018-09-17

Added the description about the information that will be lost after mainboard replacement and needs to be configured again after the mainboard is replaced. Added the link for importing and exporting the BMC configuration file to sections Installing the Mainboard and Removing the Mainboard.

28

2018-08-17

Added the procedure for removing a holding rail. For details, see Removing the Server.

27

2018-07-12

Added procedures for removing and installing an SD card and related precautions. For details, see Removing an SD Card Board and Installing an SD Card Board.

26

2018-05-29

Changed LOM and NIC to flexible NIC.

25

2018-05-10

Modified fan module removal and installation procedures. For details, see Removing a Fan Module and Installing a Fan Module.

24

2018-04-10

Modified RAID controller card supercapacitor removal and installation procedures. For details, see Removing the Supercapacitor (Screw-in RAID Controller Card), Removing the Supercapacitor (PCIe Plug-in RAID Controller Card), Installing the Supercapacitor (Screw-in RAID Controller Card), and Installing the Supercapacitor (PCIe Plug-in RAID Controller Card).

23

2018-02-22

Added the description about how to import and export the iBMC/BIOS configuration information after the mainboard is replaced. For details, see 7.41 Removing the Mainboard and 7.42 Installing the Mainboard.

22

2018-01-15

Added the locations of dual SD cards. For details, see 7.47 Removing an SD Card.

Added the description about the left and right mounting ears. For details, see 2.2 Appearance.

Added 750 W Titanium PSU indicator states and their meanings. For details, see 2.4 Indicators and Buttons.

21

2017-12-12

Modified server installation environment requirements. For details, see 3.2 Installation Environment.

Added fan module numbers. For details, see 7.15 Removing a Fan Module.

20

2017-10-26

Added the description about SD cards and dual-SD module. For details, see 2.5 Physical Structure.

19

2017-09-26

Changed optional chip types. For details, see 2.7 Internal Cabling.

18

2017-08-15

Optimized chapters about parts replacement. For details, see 7 Replacing Parts.

17

2017-07-20

Added the description about 128 GB DIMMs. For details, see 2.5 Physical Structure and 2.11 Product Specifications.

16

2017-06-20

Added internal cable BOMs. For details, see 2.7 Internal Cabling.

15

2017-05-10

Modified the mainboard layout description. For details, see 2.6 Mainboard Layout.

14

2017-04-05

Modified front bezel description. For details, see 7.3 (Optional) Removing the Front Bezel and 7.4 (Optional) Installing the Front Bezel.

13

2017-03-03

Modified the configuration description. For details, see 2.1 Introduction.

12

2017-01-24

Added description about replacing the front bezel during hard disk replacement. For details, see 7.5 Removing a Hard Disk and 7.6 Installing a Hard Disk.

11

2016-11-29

Added information about CPU installation tool. For details, see 7.37 Removing a CPU and 7.38 Installing a CPU.

Modified the indicator status description of the NVMe PCIe SSD installation. For details, see 7.8 Installing an NVMe PCIe SSD.

10

2016-10-10

Modified the disk installation direction for servers that support 8 x 2.5-inch, 24 x 2.5-inch, or 25 x 2.5-inch hard disks. For details, see 2.2 Appearance.

09

2016-07-30

Added security description. For details, see 1 Safety Instructions.

Added the description of the Software and Configuration Utility. For details, see 6 Software and Configuration Utility.

08

2016-03-30

Added the procedures for removing and installing an NVMe PCIe SSD. For details, see 7.7 Removing an NVMe PCIe SSD and 7.8 Installing an NVMe PCIe SSD.

Added the procedures for removing and installing an M.2 SATA SSD card. For details, see 7.61 Removing an M.2 SATA SSD Card and 7.62 Installing an M.2 SATA SSD Card.

07

2015-11-06

Modified the mainboard layout description. For details, see 2.6 Mainboard Layout.

06

2015-10-15

Added the procedure for operating the front bezel. For details, see 7.3 (Optional) Removing the Front Bezel and 7.4 (Optional) Installing the Front Bezel.

Added internal cabling. For details, see 2.7 Internal Cabling.

05

2015-06-10

Added the procedure for removing the RH2288 V3 installed on the holding rails. For details, see 7.11 Removing the Chassis Cover.

04

2015-03-27

Added product specifications. For details, see 2.11 Product Specifications.

03

2014-12-30

Modified the product name.

02

2014-12-10

Added the guide rail requirements on the chassis. For details, see 2.12 Physical Specifications.

01

2014-08-30

This issue is the first official release.

ダウンロード
Updated: 2018-09-26

ドキュメント番号: EDOC1000055104

閲覧数:39916

ダウンロード: 15397

Average rating:
This Document Applies to these Products
関連ドキュメント
Share
戻る 次へ