選択した言語が見つかりません。

このサイトはCookieを使用しています。 サイトを閲覧し続けることで、Cookieの使用に同意したものとみなされます。プライバシーポリシーを読む>

E9000 Server V100R001 Upgrade Guide 13

Rate and give feedback :
この文書の日本語を含む他言語への翻訳は、元の文書の内容の理解を支援する目的で提供されています。翻訳には機械翻訳が利用され、人間による簡単な校正のみが行われています。 注: 最先端の機械翻訳を利用した場合でも、翻訳の品質はプロの翻訳者による翻訳ほど十分ではありません。ファーウェイは、翻訳の正確性についていかなる責任も負わないものとします。リンクを使用して、英語版の元の文書も同時に参照することを推奨します。
About This Document

About This Document

Purpose

This document applies to the E9000 server. It describes how to upgrade the MM910, chassis intelligent display, compute nodes, pass-through modules, switch modules, and mezzanine cards as well as how to resolve common problems.

Intended Audience

This document is intended for engineers who perform the upgrade or rollback. The engineers must:

  • Be familiar with the system networking and the version information of network elements (NEs) on the network.
  • Be experienced in performing operations on and maintaining the system.

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol

Description

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results.

NOTICE is used to address practices not related to personal injury.

Calls attention to important information, best practices and tips.

NOTE is used to address information not related to personal injury, equipment damage, and environment deterioration.

Change History

Changes between document issues are cumulative. The latest document issue contains all changes made in previous issues.

Issue

Date

Description

13

2018-11-01

12

2018-06-30

11

2018-04-25

10

2017-12-27

09

2017-07-10

08

2017-04-20

07

2017-04-13

06

2017-03-31

  • This issue is the sixth official release.
  • Added the upgrade procedure for the FC switching plane MX220 of the CX220.
  • Added Using the MM910 WebUI.
  • Deleted the original section 8.5.4 that described how to upgrade the switching plane from V5 to V8 using the CLI.

05

2016-11-26

  • This issue is the fifth official release.
  • Added the upgrade procedures for the following modules:
    • CH121H V3
    • CX320
    • CX920

04

2016-10-08

  • This issue is the fourth official release.
  • Added the upgrade procedures for the following modules:
    • CX318
    • CX620
    • MZ620
    • MZ622

03

2016-07-20

02

2016-05-04

  • This issue is the second official release.
  • Added a section about batch upgrade.
  • Added the upgrade procedures for the following modules:
    • FC switching plane (MX210) of the CX210 or CX912
    • FC switching plane (MX510) of the CX311, CX911, or CX915
    • CX610
    • CX611
    • CX710
    • MZ610
    • MZ611
    • MZ612
    • MZ613
    • SD card controller

01

2015-08-07

This issue is the first official release.

ダウンロード
Updated: 2018-11-01

ドキュメント番号: EDOC1000081379

閲覧数:34953

ダウンロード: 4673

Average rating:
This Document Applies to these Products
関連ドキュメント
Share
戻る 次へ