選択した言語が見つかりません。

このサイトはCookieを使用しています。 サイトを閲覧し続けることで、Cookieの使用に同意したものとみなされます。プライバシーポリシーを読む>

WLAN Product Interoperation Configuration Guide

Rate and give feedback :
この文書の日本語を含む他言語への翻訳は、元の文書の内容の理解を支援する目的で提供されています。翻訳には機械翻訳が利用され、人間による簡単な校正のみが行われています。 注: 最先端の機械翻訳を利用した場合でも、翻訳の品質はプロの翻訳者による翻訳ほど十分ではありません。ファーウェイは、翻訳の正確性についていかなる責任も負わないものとします。リンクを使用して、英語版の元の文書も同時に参照することを推奨します。
About This Document

About This Document

Purpose

This document describes how to configure interoperation between Huawei WLAN products and other authentication servers in different scenarios.

Intended Audience

This document is intended for network engineers responsible for WLAN configuration and management. You should be familiar with basic Ethernet knowledge and have extensive experience in network deployment and management.

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol

Description

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results.

NOTICE is used to address practices not related to personal injury.

Calls attention to important information, best practices and tips.

NOTE is used to address information not related to personal injury, equipment damage, and environment deterioration.

Command Conventions

The command conventions that may be found in this document are defined as follows.

Convention

Description

Boldface

The keywords of a command line are in boldface.

Italic

Command arguments are in italics.

[ ]

Items (keywords or arguments) in brackets [ ] are optional.

{ x | y | ... }

Optional items are grouped in braces and separated by vertical bars. One item is selected.

[ x | y | ... ]

Optional items are grouped in brackets and separated by vertical bars. One item is selected or no item is selected.

{ x | y | ... }*

Optional items are grouped in braces and separated by vertical bars. A minimum of one item or a maximum of all items can be selected.

[ x | y | ... ]*

Optional items are grouped in brackets and separated by vertical bars. Several items or no item can be selected.

&<1-n>

The parameter before the & sign can be repeated 1 to n times.

#

A line starting with the # sign is comments.

NOTE:

The interface types, command outputs, and device models provided in this manual vary according to device configurations and may differ from the actual information.

To obtain better user experience, you are advised to set the number of columns displayed on the command line editor to 132 or higher.

Interface Numbering Conventions

Interface numbers used in this manual are examples. In device configuration, use the existing interface numbers on devices.

Security Conventions

  • Password setting

    When configuring a password, the cipher text is recommended. To ensure device security, do not disable password complexity check, and change the password periodically.

    When configuring a plaintext password, do not start and end it with %$%$, %^%#, %#%#, %@%@, or @%@%, which are considered valid ciphertext characters. The device can decrypt such as password and display the same plaintext password as that configured by the user in the configuration file. Ciphertext passwords starting and ending with %$%$, %^%#, %#%#, %@%@, or @%@% are valid. However, ciphertext passwords for different features are not interchangeable. For example, the ciphertext password generated for Authentication, Authorization, Accounting (AAA) cannot be configured for other features.

  • Encryption algorithm

    Currently, the device uses the following encryption algorithms: DES, 3DES, AES, RSA, SHA1, SHA-2, MD5 and SMS4. The encryption algorithm depends on the applicable scenario. Use the recommended encryption algorithm; otherwise, security defense requirements may be not met.

    • For the symmetrical encryption algorithm, use AES with the key of 128 bits or more.
    • For the asymmetrical encryption algorithm, use RSA with the key of 2048 bits or more.
    • For the hash algorithm, use SHA2 with the key of 256 bits or more.
    • For the HMAC algorithm, use HMAC-SHA2.
    • The encryption algorithms DES/3DES/RSA (RSA-1024 or lower)/MD5 (in digital signature scenarios and password encryption)/SHA1 (in digital signature scenarios) have a low security, which may bring security risks. If protocols allowed, using more secure encryption algorithms, such as AES/RSA (RSA-2048 or higher)/SHA2/HMAC-SHA2, is recommended.
    • SHA2 is irreversible encryption algorithm. The irreversible encryption algorithm must be used for the administrator password.
  • Personal data

    Some personal data (such as the MAC or IP addresses of users) may be obtained or used during operation or fault location of your purchased products, services, features, so you have an obligation to make privacy policies and take measures according to the applicable law of the country to protect personal data.

Configuration Conventions

Large-scale or batch service configuration using scripts may cause high CPU usage, preventing the system from processing regular services.

ダウンロード
Updated: 2018-07-26

ドキュメント番号: EDOC1000113779

閲覧数:9191

ダウンロード: 1325

Average rating:
This Document Applies to these Products
関連ドキュメント
Share
戻る 次へ