AR201VW-P

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 Hardware Description

This document describes hardware components of the AR, including the cabinet, chassis, power supply facilities, fan modules, cards, cables, and pluggable modules for interfaces. You can find useful information about AR hardware components from this document.

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

AR201VW-P

Version Mapping

Table 4-432 lists the mapping between the AR201VW-P router and software versions.

Table 4-432 Mapping between the AR201VW-P router and software versions

Router Model	Software Version
AR201VW-P	V200R003C00 and later versions

Appearance and Structure

Figure 4-123 shows the appearance of the AR201VW-P router.

Figure 4-123 AR201VW-P appearance
Click to enlarge

1	USB interface (host)	2	Three Wi-Fi antennas
3	CON/AUX interface NOTE: The AR201VW-P does not support AUX login.	4	WAN interface: FE electrical interface
5	LAN interfaces: eight FE electrical interfaces NOTE: LAN interface FE0 can be configured as a WAN interface. FE6 is a management interface and is used to upgrade the router. V200R007C00 and later versions: all FE LAN interfaces can be configured as WAN interfaces.	6	RESET button NOTE: This button is used to reset the router. To restore the factory settings, hold down the button for at least 5 seconds. To reset the system, press the button for less than 5 seconds. Resetting the router will interrupt services. Exercise caution when deciding to press this button.
7	Power jack NOTE: The router uses a 4-pin 36 W power adapter.	8	Jack for power cable locking strap NOTE: Insert a power cable locking strap in this jack to secure the power cable.
9	PoE power jack NOTE: The PoE power jack connects to a 100 W PoE power adapter to provide power for PDs (such as IP phones, WLAN APs, and cameras) connected to Ethernet interfaces of the router.	10	Four FXS interfaces NOTE: The FXS interfaces can be connected to analog telephones using a Universal Telephone Cable.
11	One FXO interface NOTE: The FXO interface can be connected to a public switched telephone network (PSTN) using a Universal Telephone Cable.	12	Three Wi-Fi antenna interfaces
13	Product model silkscreen	14	Ground point NOTE: Reliably ground the router by connecting a ground cable to the ground point to protect the router against lightning and interference.

Indicator Description

Figure 4-124 shows the indicators on the AR201VW-P router.

Figure 4-124 Indicators on the AR201VW-P
Click to enlarge

Number	Indicator	Color	Description
1	PWR	Green	Steady on: The system power supply is normal. Off: The system power is off.
2	SYS	Red and green	Slow blinking green: The system is running properly. Fast blinking green: The system is being powered on or restarting.
			Steady red: A fault that affects services has occurred. The fault cannot be rectified automatically and requires manual intervention.
			Off: The system software is not running or is resetting.
3	USB	Red and green	Steady green: The system has been upgraded or configured using a USB flash drive.
			Blinking green: The system is being upgraded or configured using a USB flash drive.
			Steady red: The system fails to be upgraded or configured using a USB flash drive.
			Off: No USB flash drive is connected, the USB interface has failed, or the indicator has failed.
4	PPP	Green	Steady on: A PPP connection has been set up. Off: No PPP connection is set up.
5	VPN	Green	Steady on: The IPSec service is running normally. Off: The IPSec service is unavailable.
6	WAN: LINK	Green	Steady on: A link has been established on the WAN interface. Off: No link is established on the WAN interface.
6	WAN: ACT	Green	Blinking: Data is being transmitted or received on the WAN interface. Off: The WAN interface is not transmitting or receiving data.
7	WLAN	Green	Blinking: The WLAN link is transmitting data. The blinking frequency changes with the traffic transmission rate on the link. Off: The WLAN link is shut down.
8	LAN/WAN (FE0)	Green	Steady on: A link has been established on the corresponding LAN/WAN interface.
			Blinking: Data is being transmitted or on the corresponding LAN/WAN interface.
			Off: No link is established on the corresponding LAN/WAN interface.
9	LAN (FE1 to FE7)	Green	Steady on: A link has been established on the corresponding LAN interface.
			Blinking: Data is being transmitted or received on the corresponding LAN interface.
			Off: No link is established on the corresponding LAN interface.
10	PoE	Green	Steady on: The PoE power supply is normal. Off: No PoE power supply is available.
11	FXS0 to FXS3	Green	Steady on: The FXS channel is being occupied by a call. Off: The FXS channel is idle.
11	FXO	Green	Steady on: The FXO channel is being occupied by a call. Off: The FXO channel is idle.

Interface Description

CON/AUX Interface

The console interface of a router can connect to an operation terminal for onsite configuration. An AUX interface can connect to a remote management center through a modem for remote configuration. Table 4-433 lists the CON/AUX interface attributes.

Table 4-433 CON/AUX interface attributes

Attribute	Description
Connector type	RJ45
Standards compliance	RS232
Working mode	Full-duplex Universal Asynchronous Receiver/Transmitter (UART)
Data equipment type	Data circuit terminal equipment (DCE) AUX interface: data terminal equipment (DTE)
Cable type	Console Cable

FE Electrical Interface

An FE electrical interface (10/100 Mbit/s auto-sensing) transmits and receives Ethernet services at 10 Mbit/s or 100 Mbit/s. Table 4-434 lists attributes of an FE electrical interface.

Table 4-434 FE electrical interface attributes

Attribute	Description
Connector type	RJ45
Interface attribute	MDI/MDIX NOTE: MDI stands for medium dependent interface, an Ethernet interface connection mode. Ethernet interfaces of most network adapters are MDI interfaces. MDIX stands for medium dependent interface crossover, a version of MDI. MDIX interfaces are usually used on hubs or LAN switches.
Standards compliance	PoE-capable FE electrical interface: IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3af, and IEEE802.3at PoE-incapable FE electrical interface: IEEE802.3, IEEE802.3u, and IEEE802.3ab
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP
Cable type	Ethernet Cable

USB Interface (Host)

A USB interface provides up to 480 Mbit/s upload and download rates. Table 4-435 lists attributes of a USB interface.

Table 4-435 USB interface attributes

Attribute	Description
Connector type	Type A
Standards compliance	USB2.0
Working mode	Host

FXS Interface

A foreign exchange station (FXS) interface is an analog subscriber line interface and can connect to an analog phone or fax machine. Table 4-436 lists attributes of an FXS interface.

Table 4-436 FXS interface attributes

Attribute	Description
Connector type	RJ11
Standards compliance	ITU Q.512 for the FXS interface ITU K.20 for overcurrent protection and overvoltage protection
Dialing mode	DTMF in accordance with GB3378
Bandwidth	300 Hz to 3400 Hz
Cable type	Universal Telephone Cable

FXO Interface

A foreign exchange office (FXO) interface is a loop trunk interface and can connect to a PSTN network. Table 4-437 lists attributes of an FXO interface.

Table 4-437 FXO interface attributes

Attribute	Description
Connector type	RJ11
Standards compliance	ITU Q.552 for the FXO interface ITU K.20 for overcurrent protection and overvoltage protection
Dialing mode	Dual tone multiple frequency (DTMF) in accordance with GB3378
Bandwidth	300 Hz to 3400 Hz
Cable type	Universal Telephone Cable

Wi-Fi Antenna Interface

A Wi-Fi antenna interface connects to a Wi-Fi antenna to transmit and receive data. Table 4-438 lists attributes of a Wi-Fi antenna interface.

Table 4-438 Wi-Fi antenna interface attributes

Attribute	Description
Connector type	RP-SMA-K (screw threads outside and a pin inside)
Standards compliance	2.4 GHz: 802.11b/g/n 5.0 GHz: 802.11a/n
Frequency bands supported	2.4 GHz 5.0 GHz
Rate	450 Mbit/s
MIMO mode (Tx x Rx)	3x3
Gain	2.15 dBi/3.0 dBi
Cable type	Wi-Fi Whip Antenna

Technical Specifications

Table 4-439 lists the technical specifications of the AR201VW-P router.

Table 4-439 AR201VW-P technical specifications

Item	Specification
System parameters
Processor	Dual-core, 533 MHz
Memory	512 MB
Flash	512 MB
Micro SD card (default: sd1)	None
Hard disk	Not supported
Dimensions and weight
Dimensions (H x W x D)	With no mounting bracket installed: 44.0 mm x 300.0 mm x 216.4 mm (1.73 in. x 11.81 in. x 8.52 in.) With mounting brackets installed: 44.0 mm x 482.6 mm x 216.4 mm (1.73 in. x 19.00 in. x 8.52 in.)
Weight	2.8 kg (6.17 lb)
Power specifications
Rated input voltage range (AC)	100 V to 240 V, 50 Hz/60 Hz
Maximum input voltage range (AC)	90 V AC to 264 V AC, 47 Hz to 63 Hz
Maximum output current	3 A
Maximum output power	36 W
RPS power supply	Not supported
PoE power supply	Supported (FE0-FE7)
Power consumption
Maximum power consumption	23 W
Heat dissipation
Fans	None
Airflow (facing the front panel)	None
Interface density
Management interfaces	1 (RJ45)
CON/AUX interfaces	1 (RJ45)
USB 2.0 interfaces	1
Service interfaces (standard configuration)	WAN interface: 1 FE electrical interface LAN interfaces: eight FE electrical interfaces, in which FE0 can be configured as a WAN interface and three Wi-Fi antenna interfaces Voice interfaces: four FXS interfaces and one FXO interfaces
Extended slots	Not supported
Environment parameters
Operating temperature	0°C to 45°C (32°F to 113°F) NOTE: When the altitude is between 1800 m and 5000 m, the highest operating temperature reduces by 1°C every time the altitude increases by 220 m.
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Operating relative humidity	5% to 95%, noncondensing
Operating altitude	< 5000 m (16404.2 ft.)
Part number	02354975

Version Mapping
Appearance and Structure
Indicator Description
Interface Description
Technical Specifications

Translation

简体中文

Download

Updated: 2023-08-08

Document ID: EDOC1000009848

Downloads: 19170

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate