AR2204XE
Version Mapping
Table 4-645 lists the mapping between the AR2204XE series routers and software versions.
Appearance and Structure
Figure 4-235 shows the appearance of the AR2204XE router.
The RESET button is used to reset the router.
Resetting the router will interrupt services. Exercise caution when deciding to press this button.
1 |
Two interfaces for SATA mechanical hard disks |
2 |
WAN interfaces: two 10GE optical interfaces |
3 |
WAN interfaces: ten GE optical interfaces |
4 |
WAN interfaces: eight GE electrical interfaces NOTE:
GE10 is a management interface and is used to upgrade the router. |
5 |
Console interface |
6 |
One USB interface (host) |
7 |
Ground point NOTE:
Reliably ground the router by connecting a ground cable to the ground point to protect the router against lightning and interference. |
8 |
Product model silkscreen |
9 |
Four SIC slots |
10 |
Two PoE power jacks NOTE:
The PoE power jack connects to a 100 W PoE power adapter to provide power for PDs (such as IP phones, WLAN APs, and cameras) connected to GE interfaces of the router. |
11 |
Jack for power cable locking strap NOTE:
Insert a power cable locking strap in this jack to secure the power cable. |
12 |
Two AC power jacks NOTE:
|
Slot Distribution
- Two SIC slots can be combined into one WSIC slot by removing the guide rail between them.
- After two slots are combined into one, the new slot ID is the larger one between the two original slot IDs.
Figure 4-236 shows the slot distribution on the AR2204XE router.
- Slot 1 and slot 2 can be combined into new slot 2.
- Slot 3 and slot 4 can be combined into new slot 4.
When only one WSIC card is installed on the router, you can only install the WSIC card in slot 4 (combined of slot 3 and slot 4).
- Slot 2 and slot 4 can be combined into new slot 4.
Indicator Description
Figure 4-237 shows the indicators on the AR2204XE router.
Number |
Indicator |
Color |
Description |
|---|---|---|---|
1 |
PWR |
Green |
Steady on: The router is powered by the built-in power module normally. Off: The router is not powered on. |
2 |
SYS |
Green |
Slow blinking: The system is running properly. Fast blinking: The system is being powered on or restarting. |
Red |
Steady on: A fault that affects services has occurred and cannot be rectified automatically. The fault needs to be rectified manually. |
||
Off |
The system software is not running or is resetting. |
||
3 |
PoE |
Green |
Steady on: The PoE power supply is normal. Off: No PoE power supply is available. |
4 |
10GE optical interface indicators (10GE0 to 10GE1) |
Green |
Steady on: A link has been established on the corresponding 10GE optical interface. Blinking: Data is being transmitted or received on the corresponding 10GE optical interface. Off: No link is established on corresponding 10GE optical interface. |
5 |
GE optical interface indicators (GE0 to GE9) |
Green |
Steady on: A link has been established on the corresponding GE optical interface. Blinking: Data is being transmitted or received on the corresponding GE optical interface. Off: No link is established on corresponding GE optical interface. |
6 |
GE electrical interface indicators (GE10 to GE17) |
Green |
Steady on: A link has been established on the corresponding GE electrical interface. |
Off: No link is established on the corresponding GE electrical interface. |
|||
Yellow |
Blinking: Data is being transmitted or received on the corresponding GE electrical interface. |
||
Off: No data is being transmitted or received on the corresponding GE electrical interface. |
|||
7 |
ACT (USB) |
Red and green |
Steady green: The system has been upgraded or configured using a USB flash drive. |
Blinking green: The system is being upgraded or configured using a USB flash drive. |
|||
Steady red: The system fails to be upgraded or configured using a USB flash drive. |
|||
Off: No USB flash drive is connected, the USB interface has failed, or the indicator has failed. |
|||
8 |
Hard disk ACT indicator |
Green |
Steady on: A hard disk is present. Blinking: The system is performing read-write operation on the hard disk. Off: No hard disk is present. |
9 |
Hard disk error indicator |
Red |
Steady on: The hard disk does not work normally. Off: The hard disk is working normally. |
Interface Description
Console interface
GE electrical interface
Attribute |
Description |
|---|---|
Connector type |
RJ45 |
Interface attribute |
MDI/MDIX NOTE:
|
Standards compliance |
IEEE802.3, IEEE802.3u, IEEE802.3ab |
Frame format |
Ethernet_II, Ethernet_SAP, Ethernet_SNAP |
Network protocol |
IP |
Cable type |
GE optical interface
For V200R010C00SPC600 and later versions, the GE optical interface supports copper module, and the GE optical interface configured with copper module only supports GE mode.
Attribute |
Description |
|---|---|
Connector type |
LC/PC |
Optical interface attributes |
The optical interface attributes vary depending on the optical module used. For details, see GE eSFP Optical Modules and FE SFP/eSFP Optical Modules. |
Standards compliance |
IEEE 802.3z |
10GE optical interface
Attribute |
Description |
|---|---|
Connector type |
LC/PC |
Optical interface attributes |
The optical interface attributes vary depending on the optical module used. For details, see 10GE SFP+ Optical Modules. |
Standards compliance |
IEEE 802.3ae |
USB interface (host)
Heat Dissipation
The AR2204XE router uses built-in fans to cool the system. The fans are unpluggable.
Seen from the front panel, the airflow is left to right, as shown in Figure 4-238. Cold air flows into the router from the left side and is exhausted from the right side, taking away heat generated by the router.
Technical Specifications
Table 4-651 lists the technical specifications of the AR2204XE router.
Item |
Specification |
|---|---|
System parameters |
|
Processor |
8-core, 1.5 GHz |
Memory |
4 GB |
Flash |
512 MB |
Micro SD card (default sd1) |
None |
Hard disk |
Supported |
Dimensions and weight |
|
Dimensions (H x W x D) |
|
Weight |
5 kg (11.02 lb) |
Power specifications |
|
Rated input voltage |
100 V AC to 240 V AC, 50 Hz/60 Hz |
Maximum AC input voltage |
90 V AC to 264 V AC, 47 Hz to 63 Hz |
Maximum input current |
2 A |
Maximum output power |
150 W |
RPS power supply |
Not supported |
PoE power supply |
Supported (interfaces GE10 to GE17) |
Power consumption (empty chassis) |
|
Typical power consumption |
70 W |
Maximum power consumption |
85 W |
Heat dissipation |
|
Fans |
Built-in, unpluggable |
Airflow (facing the front panel) |
Left to right |
Interface density |
|
Management interfaces |
1 (RJ45) |
Console interfaces |
1 (RJ45) |
USB 2.0 interfaces |
1 |
Service interfaces |
WAN interfaces: 8 GE electrical interfaces, 2 10GE optical interfaces, and 10 GE optical interfaces |
Extended slots |
4xSIC |
Environment parameters |
|
Operating temperature |
0°C to +45°C (32°F to 113°F) NOTE:
When the altitude is 1800-5000 m (5906-16404.2 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 300 m (984 ft.). |
Storage temperature |
-40°C to +70°C (-40°F to +158°F) |
Operating relative humidity |
5% to 95%, noncondensing |
Operating altitude |
< 5000 m (16404.2 ft.) |
Part number |
02351HLE |