AR169CVW-4B4S

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 Hardware Description

This document describes hardware components of the AR, including the cabinet, chassis, power supply facilities, fan modules, cards, cables, and pluggable modules for interfaces. You can find useful information about AR hardware components from this document.

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

AR169CVW-4B4S

Version Mapping

Table 4-302 describes the mapping between the AR169CVW-4B4S router and software versions.

Table 4-302 Mapping between the AR169CVW-4B4S router and software versions

Router Model	Software Version
AR169CVW-4B4S	V200R008C50 and later versions

Appearance and Structure

Figure 4-93 shows the appearance of the AR169CVW-4B4S router.

Figure 4-93 AR169CVW-4B4S appearance
Click to enlarge

1	Four Wi-Fi antennas	2	WAN interface: VDSL interface NOTE: This interface supports the dying gasp function.
3	WAN interface: GE optical interface	4	LAN interfaces: four GE electrical interfaces NOTE: GE0 is a management interface and is used to upgrade the router. All GE LAN interfaces can be configured as WAN interfaces.
5	Four ISDN interfaces	6	Four FXS interfaces
7	One FXO interface	8	Power jack NOTE: The router uses a 1-pin 36 W power adapter.
9	Product model silkscreen	10	Console interface
11	USB interface (host)	12	RESET button NOTE: This button is used to reset the router. To restore the factory settings, hold down the button for at least 5 seconds. To reset the system, press the button for less than 5 seconds. Resetting the router will interrupt services. Exercise caution when deciding to press this button.

Indicator Description

Figure 4-94 shows the indicators on the AR169CVW-4B4S router.

Figure 4-94 Indicators on the AR169CVW-4B4S
Click to enlarge

Number	Indicator	Color	Description
1	PWR	Green	Steady on: The system power supply is normal. Off: The system power is off.
2	SYS	Red and green	Slow blinking green: The system is running properly. Fast blinking green: The system is being powered on or restarting.
			Steady red: A fault that affects services has occurred. The fault cannot be rectified automatically and requires manual intervention.
			Off: The system software is not running or is resetting.
3	USB	Red and green	Steady green: The system has been upgraded or configured using a USB flash drive.
			Blinking green: The system is being upgraded or configured using a USB flash drive.
			Steady red: The system fails to be upgraded or configured using a USB flash drive.
			Off: No USB flash drive is connected, the USB interface has failed, or the indicator has failed.
4	PPP	Green	Steady on: A PPP connection has been established. Off: No PPP connection is established.
5	VPN	Green	Steady on: The IPSec service is running normally. Off: The IPSec service is unavailable.
6	VDSL	Green	Steady on: A VDSL link has been established.
6	VDSL	Green	Off: No VDSL link is established.
7	GE (GE0 to GE4)	Green	Steady on: A link has been established on the corresponding GE interface.
			Blinking: Data is being transmitted or received on the corresponding GE interface.
			Off: No link is established on the corresponding GE interface.
8	WLAN	Green	Blinking: Data is being transmitted on the WLAN link.
8	WLAN	Green	Off: The WLAN link is shut down.
9	ISDN (ISDN0 to ISDN3)	Green	Steady on: The corresponding ISDN channel is active.
			Blinking: Data is being transmitted on the corresponding ISDN channel.
			Off: The corresponding ISDN channel is inactive.
10	FXS (FXS0 to FXS3)	Green	Steady on: The corresponding FXS channel is being occupied by a call.
10	FXS (FXS0 to FXS3)	Green	Off: The corresponding FXS channel is idle.
11	FXO	Green	Steady on: The FXO channel is being occupied by a call.
11	FXO	Green	Off: The FXO channel is idle.

Interface Description

Console interface

A console interface can connect to an operation terminal for onsite configuration. Table 4-303 lists attributes of a console interface.

Table 4-303 Console interface attributes

Attribute	Description
Connector type	RJ45
Standards compliance	RS232
Working mode	Full-duplex Universal Asynchronous Receiver/Transmitter (UART)
Data equipment type	Data Circuit-terminating Equipment (DCE)
Cable type	Console Cable

USB interface (host)

A USB interface provides up to 5 Gbit/s upload and download rates. Table 4-304 lists attributes of a USB interface.

Table 4-304 USB interface attributes

Attribute	Description
Connector type	Type A
Standards compliance	USB3.0, USB2.0
Working mode	Host

GE electrical interface

A GE electrical interface (10/100/1000 Mbit/s auto-sensing) transmits and receives Ethernet services at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s. Table 4-305 lists attributes of a GE electrical interface.

Table 4-305 GE electrical interface attributes

Attribute	Description
Connector type	RJ45
Interface attribute	MDI/MDIX NOTE: MDI stands for medium dependent interface, an Ethernet interface connection mode. Ethernet interfaces of most network adapters are MDI interfaces. MDIX stands for medium dependent interface crossover, a version of MDI. MDIX interfaces are usually used on hubs or LAN switches.
Standards compliance	IEEE802.3, IEEE802.3u, IEEE802.3ab
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP
Cable type	Ethernet Cable

GE optical interface

A GE optical interface can transmit and receive service traffic at 100 Mbit/s or 1000 Mbit/s. Table 4-306 lists attributes of a GE optical interface.

Table 4-306 GE optical interface attributes

Attribute	Description
Connector type	LC/PC
Optical interface attributes	The optical interface attributes vary depending on the optical module used. For details, see GE eSFP Optical Modules and FE SFP/eSFP Optical Modules.
Standards compliance	IEEE 802.3z

VDSL interface

A very-high-speed digital subscriber line (VDSL) interface transmits service data from a LAN to an upstream device at a high speed. Table 4-307 lists attributes of a VDSL interface.

Table 4-307 VDSL interface attributes

Attribute	Description
Connector type	RJ11
Standards compliance	ITU-T G.993.2 ITU-T G.992.5 ITU-T G.992.3 ITU-T G.992.1 G.DMT ANSI T1.413 Issue 2
Rate	ADSL2+ full rate mode (ITU-T G.992.5): downlink rate of 24 Mbit/s and uplink rate of 1 Mbit/s VDSL2 mode (ITU-T G.993.2): downlink rate of 100 Mbit/s and uplink rate of 50 Mbit/s ADSL2 full rate mode (ITU-T G.992.3): downlink rate of 12 Mbit/s and uplink rate of 1 Mbit/s ADSL full rate mode (G.992.1 G.DMT): downlink rate of 8 Mbit/s and uplink rate of 1 Mbit/s
Cable type	Universal Telephone Cable

ISDN interface

An ISDN S/T interface can connect to an integrated services digital network (ISDN) to provide voice services. Table 4-308 lists attributes of an ISDN S/T interface.

Table 4-308 ISDN S/T interface attributes

Attribute	Description
Connector type	RJ45
Standards compliance	ITU-T I.430 Q.921 Q.931
Rate	192 kbit/s
Bandwidth	0 MHz to 100 MHz
Cable type	ISDN Cable

FXS interface

A foreign exchange station (FXS) interface is an analog subscriber line interface and can connect to an analog phone or fax machine. Table 4-309 lists attributes of an FXS interface.

Table 4-309 FXS interface attributes

Attribute	Description
Connector type	RJ11
Standards compliance	ITU Q.512 for the FXS interface ITU K.20 for overcurrent protection and overvoltage protection
Dialing mode	DTMF in accordance with GB3378
Bandwidth	300 Hz to 3400 Hz
Cable type	Universal Telephone Cable

FXO interface

A foreign exchange office (FXO) interface is a loop trunk interface and can connect to a PSTN network. Table 4-310 lists attributes of an FXO interface.

Table 4-310 FXO interface attributes

Attribute	Description
Connector type	RJ11
Standards compliance	ITU Q.552 for the FXO interface ITU K.20 for overcurrent protection and overvoltage protection
Dialing mode	Dual tone multiple frequency (DTMF) in accordance with GB3378
Bandwidth	300 Hz to 3400 Hz
Cable type	Universal Telephone Cable

Wi-Fi antenna interface

Wi-Fi antennas have been installed on Wi-Fi interfaces of a router before delivery.

A Wi-Fi antenna interface connects to a Wi-Fi antenna to transmit and receive data. Table 4-311 lists attributes of a Wi-Fi antenna interface.

Table 4-311 Wi-Fi antenna interface attributes

Attribute	Description
Standards compliance	802.11a/b/g/n/ac
Frequency bands supported	2.4 GHz 5.0 GHz
Rate	1167 Mbit/s
MIMO mode (Tx x Rx)	2x2
Gain	2.4 GHz: 1.9 dBi 5.0 GHz: 3.4 dBi
Services provided	Layer 2/3 wireless access Wireless data encryption WLAN security

Technical Specifications

Table 4-312 lists the technical specifications of the AR169CVW-4B4S router.

Table 4-312 AR169CVW-4B4S technical specifications

Item	Specification
System parameters
Processor	Dual-core, 1 GHz
Memory	512 MB
Flash	512 MB
Micro SD card	Not supported
Hard disk	Not supported
Dimensions and weight
Dimensions (H x W x D)	30 mm x 270 mm x 155 mm (1.18 in. x 10.63 in. x 6.10 in.)
Weight	0.8 kg (1.76 lb)
Power specifications
Rated input voltage range (AC)	110 V to 220 V, 50/60 Hz
Maximum input voltage range (AC)	90 V to 270 V, 47 Hz to 63 Hz
Maximum output current	3 A
Maximum output power	36 W
RPS power supply	Not supported
PoE power supply	Not supported
Power consumption
Maximum power consumption	18.6 W
Heat dissipation
Fans	None
Airflow (facing the front panel)	None
Interface density
Management interfaces	1 (RJ45)
CON/AUX interfaces	1 (RJ45)
USB 3.0 interfaces	1
Service interfaces	WAN interfaces: one GE optical interface and one VDSL interface LAN interfaces: four GE electrical interfaces Voice interfaces: four ISDN interfaces, four FXS interfaces, and one FXO interface
Extended slots	Not supported
Environment parameters
Operating temperature	0°C to 40°C (32°F to 104°F) NOTE: When the altitude is 1800-5000 m (5906-16404.2 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Operating relative humidity	5% to 95%, noncondensing
Operating altitude	< 5000 m (16404.2 ft.)
Part number	50010351

Version Mapping
Appearance and Structure
Indicator Description
Interface Description
Technical Specifications

Translation

简体中文

Download

Updated: 2023-08-08

Document ID: EDOC1000009848

Downloads: 19217

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate