Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document.
Note: Even the most advanced machine translation cannot match the quality of professional translators.
Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Parameter Description
- Transmit optical power
- Output optical power of an optical module when it is working properly. When two optical modules are connected, the transmit optical power of one end must be within the range of receive optical power on the other end.
- Receive optical power
- Average input optical power that the receiver of an optical module can receive within a range of bit error rate (BER = 10-12). The upper limit of this parameter is the overload optical power and the lower limit is the maximum receiver sensitivity. When two optical modules are connected, the receive optical power on one end determines the range of transmit optical power on the other end.
- Maximum receiver sensitivity
- Minimum average input optical power that the receiver of an optical module can receive within a range of bit error rate (BER = 10-12). When two optical modules are connected, the maximum receiver sensitivity on one end determines the minimum value of transmit optical power on the other end.
- Overload optical power
- Maximum average input optical power that the receiver of an optical module can receive within a range of bit error rate (BER = 10-12). When two optical modules are connected, the overload optical power on one end determines the maximum transmit optical power on the other end.
- Extinction ratio
- Minimum ratio of the average optical power with signals transmitted against the average optical power without signals transmitted in complete modulation mode. The extinction ratio indicates the capability of an optical module to identify signal 0 and signal 1. This parameter is a quality indicator for optical modules. Optical modules with a large extinction ratio may not have good quality. Qualified optical modules should have an extinction ratio complying with IEEE 802.3.
- Fiber mode
- Mode of optical fibers defined based on core diameters and features of optical fibers. Optical fibers are classified into single-mode and multimode fibers. Generally, multi-mode fibers have large core diameters and severe dispersion, so they transmit optical signals over short distances. Single-mode fibers have small dispersion and can transmit optical signals over long distances.
- Modal bandwidth
- Bandwidth measured at a point with transmit power several dB lower than that of the point with the peak center wavelength. Modal bandwidth reflects spectrum characteristics of multimode fibers. The higher modal bandwidth a multimode fiber has, the longer transmission distance the fiber supports.
- Fiber diameter
- Diameter of the core of a fiber. According to international standards for optical fibers, the diameter of a multimode fiber is 62.5 μm or 50 μm, and the diameter of a single-mode fiber is 9 μm. Select optical fibers with diameters supported by the optical modules.
- Fiber class
- The following fiber classes are defined: multimode fiber (G.651), common single-mode fiber (G.652), shifted dispersion fiber (G.653), and non-zero shifted dispersion fiber (G.655). G.651 and G.652 are commonly used fiber classes. Optical fibers of higher classes support longer transmission distances. When selecting optical fibers for optical modules, determine the classes of fibers based on the required transmission distances.
- Connector type
- Type of the interface on an optical module to accommodate a fiber. Commonly used connector types are LC (applicable to all the SFP, SFP+, and XFP modules), SC, and MPO (applicable to 150 m QSFP+ and CXP modules). Select optical fibers with connectors supported by the optical modules.
- Transmission distance
- Maximum distance over which optical signals can transmit. Optical signals sent from different types of sources can transmit over different distances because they have different dispersion and attenuation. When connecting optical interfaces, select optical modules and fibers according to the longest signal transmission distance.
- Interface rate
- Maximum rate of electrical signals that an optical component can transmit without bit errors. The interface rates defined in Ethernet standards include 125 Mbit/s, 1.25 Gbit/s, 10.3125 Gbit/s, and 41.25 Gbit/s. When connecting optical interfaces, select optical modules and fibers based on the maximum signal transmission rate.