AR169JFVW-4B4S

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 Hardware Description

This document describes hardware components of the AR, including the cabinet, chassis, power supply facilities, fan modules, cards, cables, and pluggable modules for interfaces. You can find useful information about AR hardware components from this document.

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

AR169JFVW-4B4S

Version Mapping

Table 4-352 lists the mapping between the AR169JFVW-4B4S router and software versions.

Table 4-352 Version mapping

Router Model	Software Version
AR169JFVW-4B4S	V200R009C00 and later versions

Appearance and Structure

Figure 4-105 shows the appearance of the AR169JFVW-4B4S router.

Figure 4-105 AR169JFVW-4B4S appearance
Click to enlarge

1	USB interface (host)	2	Four FXS interfaces NOTE: The FXS interfaces can be connected to analog telephones using a Universal Telephone Cable.
3	CON/AUX interface NOTE: The AR169JFVW-4B4S does not support AUX login.	4	WAN interface: GE combo interface
5	LAN interfaces: four GE electrical interfaces NOTE: GE0 is a management interface and is used to upgrade the router. All GE LAN interfaces can be configured as WAN interfaces.	6	RESET button NOTE: This button is used to reset the router. To restore the factory settings, hold down the button for at least 5 seconds. To reset the system, press the button for less than 5 seconds. Resetting the router will interrupt services. Exercise caution when deciding to press this button.
7	Power jack NOTE: The router uses a 60 W power adapter.	8	Jack for power cable locking strap NOTE: Insert a power cable locking strap in this jack to secure the power cable.
9	One FXO interface NOTE: The FXO interface can be connected to a public switched telephone network (PSTN) using a Universal Telephone Cable.	10	Four ISDN interfaces
11	Two Wi-Fi antenna interfaces	12	Product model silkscreen
13	WAN interface: VDSL 35B interface	14	Ground point NOTE: Reliably ground the router by connecting a ground cable to the ground point to protect the router against lightning and interference.

Indicator Description

Figure 4-106 shows the indicators on the AR169JFVW-4B4S router.

Figure 4-106 Indicators on the AR169JFVW-4B4S router
Click to enlarge

Number	Indicator	Color	Description
1	PWR	Green	Steady on: The system power supply is normal. Off: The system power is off.
2	SYS	Red and green	Slow blinking green: The system is running properly. Fast blinking green: The system is being powered on or restarting.
			Steady red: A fault that affects services has occurred. The fault cannot be rectified automatically and requires manual intervention.
			Off: The system software is not running or is resetting.
3	USB	Red and green	Steady green: The system has been upgraded or configured using a USB flash drive.
			Blinking green: The system is being upgraded or configured using a USB flash drive.
			Steady red: The system fails to be upgraded or configured using a USB flash drive.
			Off: No USB flash drive is connected, the USB interface has failed, or the indicator has failed.
4	PPP	Green	Steady on: A PPP connection has been established. Off: No PPP connection is established.
5	VPN	Green	Steady on: The IPSec service is running normally. Off: The IPSec service is unavailable.
6	VDSL 35B	Green	Steady on: A link has been established on the VDSL 35B interface. Blinking: The link on the VDSL 35B interface is activating. Off: No link is established on the VDSL 35B interface.
7	GE combo interface indicator	Green	Steady on: A link has been established on the GE combo interface. Blinking: Data is being transmitted or received on the GE combo interface. Off: No link is established on the GE combo interface.
8	WLAN	Green	Blinking: The WLAN link is transmitting data. The blinking frequency changes with the traffic transmission rate on the link. Off: The WLAN link is shut down.
9	LAN/WAN (GE0)	Green	Steady on: A link has been established on the LAN/WAN interface. Blinking: Data is being transmitted or received on the LAN/WAN interface. Off: No link is established on the LAN/WAN interface.
10	LAN (GE1 to GE3)	Green	Steady on: A link has been established on the corresponding LAN interface. Blinking: Data is being transmitted or received on the corresponding LAN interface. Off: No link is established on the corresponding LAN interface.
11	FXO	Green	Steady on: There is an ongoing call on the FXO channel. Off: The FXO channel is idle.
12	FXS0 to FXS3	Green	Steady on: There is an ongoing call on the corresponding FXS channel. Off: The corresponding FXS channel is idle.
13	ISDN0 to ISDN3	ACT	Steady on: The corresponding ISDN channel is active. Off: The corresponding ISDN channel is inactive.
		B1	Blinking: The ISDN B1 channel is being occupied. Off: The ISDN B1 channel is idle.
		B2	Blinking: The ISDN B2 channel is being occupied. Off: The ISDN B2 channel is idle.

Interface Description

CON/AUX interface

The console interface of a router can connect to an operation terminal for onsite configuration. An AUX interface can connect to a remote management center through a modem for remote configuration. Table 4-353 lists the CON/AUX interface attributes.

Table 4-353 CON/AUX interface attributes

Attribute	Description
Connector type	RJ45
Standards compliance	RS232
Working mode	Full-duplex Universal Asynchronous Receiver/Transmitter (UART)
Data equipment type	Data circuit terminal equipment (DCE) AUX interface: data terminal equipment (DTE)
Cable type	Console Cable

USB interface (host)

A USB interface provides up to 480 Mbit/s upload and download rates. Table 4-354 lists attributes of a USB interface.

Table 4-354 USB interface attributes

Attribute	Description
Connector type	Type A
Standards compliance	USB2.0
Working mode	Host

GE electrical interface

A GE electrical interface (10/100/1000 Mbit/s auto-sensing) transmits and receives Ethernet services at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s. Table 4-355 lists attributes of a GE electrical interface.

Table 4-355 GE electrical interface attributes

Attribute	Description
Connector type	RJ45
Interface attribute	MDI/MDIX NOTE: MDI stands for medium dependent interface, an Ethernet interface connection mode. Ethernet interfaces of most network adapters are MDI interfaces. MDIX stands for medium dependent interface crossover, a version of MDI. MDIX interfaces are usually used on hubs or LAN switches.
Standards compliance	IEEE802.3, IEEE802.3u, IEEE802.3ab
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP
Cable type	Ethernet Cable

GE combo interface

A GE combo interface consists of an optical Ethernet interface and an electrical Ethernet interface on the panel. The two interfaces have only one internal forwarding interface. The electrical and optical interfaces are multiplexed, and only either of them can work at a time. When either of the Ethernet interfaces is working, the other interface is shut down.

The GE electrical interface (10/100/1000 Mbit/s auto-sensing) transmits and receives services at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s. It must be used with an Ethernet Cable.
The GE optical interface (100/1000 Mbit/s auto-sensing) transmits and receives services at 100 Mbit/s or 1000 Mbit/s. It must be used with an Optical Fiber, GE eSFP Optical Modules, or FE SFP/eSFP Optical Modules.

In V200R008C30 and earlier versions, a combo interface works as an electrical interface and uses a network cable to transmit and receive data by default.
In V200R008C50 and later versions, a combo interface works in auto mode and automatically works as an optical or electrical interface by default.

Wi-Fi antenna interface

A Wi-Fi antenna interface connects to a Wi-Fi antenna to transmit and receive data. Table 4-356 lists attributes of a Wi-Fi antenna interface.

Table 4-356 Wi-Fi antenna interface attributes

Attribute	Description
Connector type	RP-SMA-K (screw threads outside and a pin inside)
Standards compliance	802.11b/g/n
Frequency band supported	2.4 GHz
Rate	300 Mbit/s
MIMO mode (Tx x Rx)	2x2
Gain	2.15 dBi
Services provided	Layer 2/3 wireless access Wireless data encryption WLAN security
Cable type	Wi-Fi Whip Antenna

VDSL 35B interface

A very-high-speed digital subscriber line (VDSL) 35B interface transmits service data from a LAN to an upstream device at a high speed over a twisted pair. Table 4-357 lists attributes of a VDSL interface.

Table 4-357 VDSL 35B interface attributes

Attribute	Description
Connector type	RJ11
Standards compliance	ITU-T G.993.2 ITU-T G.992.5 ITU-T G.992.3 ITU-T G.992.1 G.DMT ANSI T1.413 Issue 2
Rate	ADSL2+ full rate mode (ITU-T G.992.5): downlink rate of 24 Mbit/s and uplink rate of 1 Mbit/s VDSL2 mode (ITU-T G.993.2): downlink rate of 100 Mbit/s and uplink rate of 50 Mbit/s ADSL2 full rate mode (ITU-T G.992.3): downlink rate of 12 Mbit/s and uplink rate of 1 Mbit/s ADSL full rate mode (G.992.1 G.DMT): downlink rate of 8 Mbit/s and uplink rate of 1 Mbit/s VDSL2 35B mode (ITU-T G.993.2): downlink rate of 350 Mbit/s and uplink rate of 40 Mbit/s
Cable type	Universal Telephone Cable

FXS interface

A foreign exchange station (FXS) interface is an analog subscriber line interface and can connect to an analog phone or fax machine. Table 4-358 lists attributes of an FXS interface.

Table 4-358 FXS interface attributes

Attribute	Description
Connector type	RJ11
Standards compliance	ITU Q.512 for the FXS interface ITU K.20 for overcurrent protection and overvoltage protection
Dialing mode	DTMF in accordance with GB3378
Bandwidth	300 Hz to 3400 Hz
Cable type	Universal Telephone Cable

FXO interface

A foreign exchange office (FXO) interface is a loop trunk interface and can connect to a PSTN network. Table 4-359 lists attributes of an FXO interface.

Table 4-359 FXO interface attributes

Attribute	Description
Connector type	RJ11
Standards compliance	ITU Q.552 for the FXO interface ITU K.20 for overcurrent protection and overvoltage protection
Dialing mode	Dual tone multiple frequency (DTMF) in accordance with GB3378
Bandwidth	300 Hz to 3400 Hz
Cable type	Universal Telephone Cable

ISDN interface

An ISDN S/T interface can connect to an integrated services digital network (ISDN) to provide voice services. Table 4-360 lists attributes of an ISDN S/T interface.

Table 4-360 ISDN S/T interface attributes

Attribute	Description
Connector type	RJ45
Standards compliance	ITU-T I.430 Q.921 Q.931
Rate	192 kbit/s
Bandwidth	0 MHz to 100 MHz
Cable type	ISDN Cable

Technical Specifications

Table 4-361 lists the technical specifications of the AR169JFVW-4B4S router.

Table 4-361 Technical specifications

Item	Specification
System parameters
Processor	Dual-core, 533 MHz
Memory	1 GB
Flash	512 MB
Micro SD card (default sd1)	None
Hard disk	Not supported
Dimensions and weight
Dimensions (H x W x D)	With no rack-mounting bracket installed: 44.0 mm x 300.0 mm x 216.4 mm (1.73 in. x 11.81 in. x 8.52 in.) With rack-mounting brackets installed: 44.0 mm x 482.6 mm x 216.4 mm (1.73 in. x 19.00 in. x 8.52 in.)
Weight	2.8 kg (6.17 lb)
Power specifications
Rated input voltage	100 V AC to 240 V AC, 50 Hz/60 Hz
Maximum AC input voltage	90 V AC to 264 V AC, 47 Hz to 63 Hz
Maximum output current	5 A
Maximum output power	60 W
RPS power supply	Not supported
PoE power supply	Not supported
Power consumption
Maximum power consumption	22 W
Heat dissipation
Fans	None
Airflow (facing the front panel)	None
Interface density
Management interfaces	1 (RJ45)
CON/AUX interface	1 (RJ45)
USB 2.0 interfaces	1
Service interfaces	WAN interfaces: one GE combo interface and one VDSL 35B interface LAN interfaces: two Wi-Fi antenna interfaces and four GE electrical interfaces, among which LAN interface GE0 can be used as a WAN interface Voice interfaces: four FXS interfaces, one FXO interface, and four ISDN interfaces
Extended slots	Not supported
Environment parameters
Operating temperature	0°C to +45°C (32°F to 113°F) NOTE: When the altitude is 1800-5000 m (5906-16404.2 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Operating relative humidity	5% to 95%, noncondensing
Operating altitude	< 5000 m (16404.2 ft.)
Part number	50010389

Version Mapping
Appearance and Structure
Indicator Description
Interface Description
Technical Specifications

Translation

简体中文

Download

Updated: 2023-08-08

Document ID: EDOC1000009848

Downloads: 19188

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate