No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S5700 Series Switches Hardware Description

This document provides an overall description of the S5700 hardware, helping you obtain detailed information about each chassis, card, power module, fan module, cable, and optical module.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
S5720-28X-PWH-LI-AC

S5720-28X-PWH-LI-AC

Version Mapping

Table 4-308 lists the mapping between the S5720-28X-PWH-LI-AC chassis and software versions.

Table 4-308 Version mapping

Series

Model

Software Version
S5720-LI S5720-28X-PWH-LI-AC

V200R011C00 and later versions

Appearance and Structure

Figure 4-118 S5720-28X-PWH-LI-AC appearance
1 Sixteen PoE+ 10/100/1000BASE-T ports 2 Eight PoE++ 100M/1000M/2.5G BASE-T ports (MultiGE port)
3 Four 10GE SFP+ ports 4 One PNP button
NOTICE:

Applicable in V200R012C00 and later versions:

To restore the factory settings and reset the switch, hold down the button for at least 6 seconds.

To reset the switch, press the button.

Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.

5 One console port 6 One USB port
7 Ground screw
NOTE:
It is used with a ground cable.
8 RPS socket
NOTE:

It is used with an RPS cable, which is not hot swappable.

9 Jack for AC power cable locking strap
NOTE:
The AC power cable locking strap is not delivered with the switch.
10 AC socket
NOTE:

It is used with an AC power cable.

Port Description

10/100/1000BASE-T port
A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-309 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-309 Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3, IEEE802.3u, IEEE802.3ab

Working mode

10/100/1000 Mbit/s auto-sensing

Maximum transmission distance

100 m

100M/1000M/2.5G BASE-T port

A 100M/1000M/2.5G BASE-T port (MultiGE port) sends and receives service data at 100 Mbit/s, 1 Gbit/s, or 2.5 Gbit/s, and must use an Ethernet cable. If the 2.5 Gbit/s speed is required, the port must use an Ethernet cable of Cat5e or higher category. Table 4-310 describes the attributes of a 100M/1000M/2.5G BASE-T port.

Table 4-310 Attributes of a 100M/1000M/2.5G BASE-T port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3u, IEEE802.3ab, IEEE802.3bz, mgbase-t

Working Mode

100/1000/2500 Mbit/s auto-sensing

A 100M/1000M/2.5G BASE-T port supports the connection with the following devices:
  • All switches providing FE electrical interfaces or GE electrical interfaces
  • All devices providing MultiGE interfaces defined by the NBASE-T Alliance
  • All devices providing MultiGE interfaces that comply with the 802.3bz standard
Table 4-311 lists the maximum transmission distances of different cables on MultiGE ports.
Table 4-311 Maximum transmission distances of different cables on MultiGE ports
Cable Type (6-a-1 Bundle) MultiGE Port (Different Rates)
100M/1000M 2.5GE
Category 5e unshielded twisted pair (Cat5e UTP) 100 m 100 m
Category 5e shielded twisted pair (Cat5e STP) 100 m 200 m
Only the APs listed below are supported if the transmission distance is longer than 100 m:
  • AP7052DN/AP7152DN
  • AP6052DN
  • AP8082DN/AP8182DN
  • AP7052DE
  • AP7060DN
Category 6 unshielded twisted pair (Cat6 UTP) 100 m 100 m
Category 6 shielded twisted pair (Cat6 STP) 100 m 200 m
Only the APs listed below are supported if the transmission distance is longer than 100 m:
  • AP7052DN/AP7152DN
  • AP6052DN
  • AP8082DN/AP8182DN
  • AP7052DE
  • AP7060DN
Category 6A unshielded twisted pair (Cat6A U/UTP) 100 m 100 m
Category 6A foiled/unshielded twisted pair (Cat6A F/UTP) 100 m 200 m
Only the APs listed below are supported if the transmission distance is longer than 100 m:
  • AP7052DN/AP7152DN
  • AP6052DN
  • AP8082DN/AP8182DN
  • AP7052DE
  • AP7060DN
Category 6A shielded twisted pair (Cat6A STP) 100 m 200 m
Only the APs listed below are supported if the transmission distance is longer than 100 m:
  • AP7052DN/AP7152DN
  • AP6052DN
  • AP8082DN/AP8182DN
  • AP7052DE
  • AP7060DN
Category 7 shielded twisted pair (Cat7) 100 m 200 m
Only the APs listed below are supported if the transmission distance is longer than 100 m:
  • AP7052DN/AP7152DN
  • AP6052DN
  • AP8082DN/AP8182DN
  • AP7052DE
  • AP7060DN
NOTE:
6-a-1 stands for the six-around-one cable bundle mode, with one cable in the center and six cables bundled evenly around it.
10GE SFP+ port
A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-312 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 4-312 Attributes of a 10GE SFP+ port

Attribute

Description

Connector type

LC/PC

Optical port attributes

Depend on the optical module used

Standards compliance

IEEE802.3ae

Working mode

GE/10GE auto-sensing

Console port
The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-313.
Table 4-313 Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

USB port
The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.
NOTE:
USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5720-28X-PWH-LI-AC has the same types of indicators as the S5720-28X-PWR-LI-AC. For details, see Indicator Description.

Power Supply Configuration

The S5720-28X-PWH-LI-AC has a built-in power module and does not support pluggable power modules. It is a PoE switch. In addition to the built-in PoE power module, the switch can also connect to an RPS1800 for power redundancy.

Table 4-314 PoE power supply capacity of the built-in power module
Available PoE Power Maximum Number of Ports (Fully Loaded)
360 W
  • 802.3af (15.4 W per port): 23
  • 802.3at (30 W per port): 12
  • 802.3bt (60 W per port): 6 (only PoE++ ports)
Figure 4-119 shows the power supply mode of a built-in AC PoE power module (PWR). The PWR module receives AC power from an external power source and provides two outputs: 12 V and -53 V. The 12 V output is provided for the chassis, and the -53 V output is provided for PDs.
Figure 4-119 Power supply by a built-in AC PoE power module

L: live wire

N: neutral wire

PGND: protection ground

GND: 12 V reference ground

RTN: -53 V reference ground

Heat dissipation

The S5720-28X-PWH-LI-AC has two built-in fans for forced air cooling. Air flows in from the left side and front panel, and exhausts from the right side.

NOTE:
This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-315 lists technical specifications of the S5720-28X-PWH-LI-AC.

Table 4-315 Technical specifications

Item

Description

Memory (RAM)

512 MB

Flash

512 MB in total. To view the available flash memory size, run the display version command.

Mean time between failures (MTBF)

50.6 years

Mean time to repair (MTTR)

2 hours

Availability

> 0.99999

Service port surge protection

Common mode: ±7 kV

Power supply surge protection

±6 kV in differential mode, ±6 kV in common mode

Dimensions (H x W x D)

43.6 mm x 442.0 mm x 310.0 mm (1.72 in. x 17.4 in. x 12.2 in.)

Weight (with packaging)

5.9 kg (13.01 lb)

Stack ports

Sixteen 10/100/1000BASE-T ports and four 10GE SFP+ ports

RTC

Not supported

RPS

Supported

PoE

Supported

Rated voltage range

100 V AC to 240 V AC, 50/60 Hz

Maximum voltage range

90 V AC to 264 V AC, 47 Hz to 63 Hz

Maximum power consumption (100% throughput)

  • Not providing the PoE function: 67.3 W
  • 100% PoE loads: 473 W (system power consumption: 113 W, PoE: 360 W)
Typical power consumption (30% of traffic load)
  • Tested according to ATIS standard
  • EEE enabled
  • No PoE power consumption

51.6 W

Operating temperature

0°C to 45°C (32°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.)
NOTE:

When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

Short-term operating temperature

-5°C to +50°C (23°F to 122°F) at an altitude of 0-1800 m (0-5906 ft.)

NOTE:

When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

The equipment can operate beyond the normal operating temperature range for a short-term period, but the following conditions must be met:
  • The equipment operates at a temperature of over 45°C (113°F) consecutively for at most 96 hours in one year.
  • The equipment operates at a temperature of over 45°C (113°F) for a total of no more than 360 hours in one year.
  • The equipment operates at a temperature of over 45°C (113°F) for no more in 15 times in one year.
The equipment may be damaged or experience unexpected exceptions if any of the preceding limits is exceeded.

The equipment cannot start when the temperature is lower than 0°C (32°F). The maximum distance of optical modules used in these conditions cannot exceed 10 km.

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 55.2 dB(A)

Relative humidity

5% to 95%, noncondensing

Operating altitude

0-5000 m (0-16404 ft.)

Certification

  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

98010659
Translation
Download
Updated: 2019-08-19

Document ID: EDOC1000013597

Views: 559158

Downloads: 14299

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next