S5700-28P-LI-24S-BAT

S5700 Series Switches Hardware Description (V200)

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Version Mapping

Table 4-172 lists the mapping between the S5700-28P-LI-24S-BAT chassis and software versions.

Table 4-172 Version mapping

Series	Model	Software Version
S5700-LI-BAT	S5700-28P-LI-24S-BAT	V200R003C02 to V200R012C00 versions NOTE: This model does not match V200R003C10, V200R005C00SPC500, V200R005C01, V200R005C02, V200R005C03, or V200R007C10.

Appearance and Structure

Figure 4-66 S5700-28P-LI-24S-BAT appearance

1	Twenty 100/1000BASE-X ports Applicable modules: FE optical module GE optical module GE-CWDM optical module GE copper module (works at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s)	2	Four combo ports (10/100/1000BASE-T + 100/1000BASE-X) Modules applicable to combo optical ports: FE optical module GE optical module GE-CWDM optical module
3	Four 1000BASE-X ports Applicable modules and cables: GE optical module GE-CWDM optical module GE-DWDM optical module GE copper module (works at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s)	4	One console port
5	Ground screw NOTE: It is used with a ground cable.	6	AC socket NOTE: It is used with an AC power cable.
7	Jack for AC power cable locking strap NOTE: The AC power cable locking strap is not delivered with the switch.	8	Battery slot NOTE: Applicable battery modules or power modules: BAT-4AHA rechargeable lithium ion battery module BAT-8AHA rechargeable lithium ion battery module PBB-12AHA lead-acid battery charger module (requiring external lead-acid batteries) 150 W AC power module 150 W DC power module

Port Description

100/1000BASE-X port

A 100/1000BASE-X port can send and receive data at 100 Mbit/s or 1000 Mbit/s. Table 4-173 describes the attributes of a 100/1000BASE-X port.

Table 4-173 Attributes of a 100/1000BASE-X port

Attribute	Description
Connector type	LC/PC
Optical interface attributes	Depend on the optical module used
Standards compliance	IEEE802.3z
Working mode	100/1000 Mbit/s auto-sensing

Combo port

A combo port refers to a pair of ports consisting of an optical Ethernet port and an electrical Ethernet port on the panel. Each combo port matches only one internal forwarding port. A combo port can be configured as an electrical port or an optical port, but only one port can be active at a time. When one port is active, the other port is shut down.

By default, a combo port works in auto mode, in which the port type is determined as follows:

If the optical port has no optical module installed and the electrical port has no Ethernet cable connected, the port type depends on which port is connected first. If the electrical port is connected by an Ethernet cable first, the electrical port is used for data switching. If the optical port has an optical module installed first, the optical port is used for data switching.
If the electrical port has an Ethernet cable connected and is in Up state, the electrical port is still used for data switching when the optical port has an optical module installed.
If the optical port, no matter in Up or Down state, has an optical module installed, the optical port is still used for data switching when the electrical port has an Ethernet cable connected.
If the optical port has an optical module installed and the electrical port has an Ethernet cable connected, the optical port is used for data switching after the switch restarts.

You can configure a combo port as an electrical or optical port using the combo-port command.

1000BASE-X port

When a 1000BASE-X port uses a GE optical module, it can only transmit and receive data at 1000 Mbit/s and does not support the 100 Mbit/s transmission speed. When a 1000BASE-X port uses a GE copper module, it can transmit and receive data at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s. Table 4-174 describes the attributes of a 1000BASE-X Ethernet optical port.

Table 4-174 Attributes of a 1000BASE-X Ethernet optical port

Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the module used
Standards compliance	IEEE802.3z

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-175.

Table 4-175 Attributes of a console port

Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

Indicator Description

The S5700-28P-LI-24S-BAT has the same types of indicators as the S5700-28P-LI-BAT. For details, see Indicator Description.

Power Supply Configuration

The S5700-28P-LI-24S-BAT switch has a built-in AC power supply unit and can use a pluggable power module or battery for power redundancy. Power modules and batteries for the S5700-28P-LI-24S-BAT switch are hot swappable.

Battery module configuration

The battery installed on an S5700-28P-LI-24S-BAT switch can automatically supply power to the switch in case of a mains power outage, ensuring uninterrupted services. When the AC power supply recovers, the battery turns to the charging state.

The S5700-28P-LI-24S-BAT switch supports the following batteries and battery charger module:

BAT-4AHA (chargeable lithium battery)
BAT-8AHA (chargeable lithium battery)
PBB-12AHA (12AH lead-acid battery charger module)

The PBB-12AHA module must connect to a lead-acid battery with 12AH of rated capacity.

The S5700-28P-LI-24S-BAT switch can be configured with a battery to prevent service interruption caused by mains power outages. Table 4-176 lists the power supply time of the batteries.

Table 4-176 Battery configuration

Battery	Power Supply Time
BAT-4AHA	The switch works with the maximum power consumption and the battery is fully charged: 1.2 hours The switch has 70% of ports in Up state, each port transmits 10% of maximum traffic, and the battery is fully charged: 2.1 hours The switch works with the minimum power consumption (no port is working) and the battery is fully charged: 4.1 hours
BAT-8AHA	The switch works with the maximum power consumption and the battery is fully charged: 2.3 hours The switch has 70% of ports in Up state, each port transmits 10% of maximum traffic, and the battery is fully charged: 4.2 hours The switch works with the minimum power consumption (no port is working) and the battery is fully charged: 8.3 hours

The power supply time shortens when a battery has been used for a long time.

Battery module configuration

The S5700-28P-LI-24S-BAT switch can be configured with a power module as a backup of the built-in power supply unit to improve power reliability.

The S5700-28P-LI-24S-BAT switch supports the following power modules:

150 W AC power module
150 W DC power module

Heat Dissipation

The S5700-28P-LI-24S-BAT has two built-in fans for forced air cooling. The airflow direction is left-to-right.

Click to enlarge

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-177 lists technical specifications of the S5700-28P-LI-24S-BAT.

Table 4-177 Technical specifications

Item	Description
Memory (RAM)	256 MB
Flash	200 MB
Mean time between failures (MTBF)	45
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Service port surge protection	Common mode: ±6 kV
Power supply surge protection	Built-in AC or using AC power modules: ±6 kV in differential mode, ±6 kV in common mode Using DC power modules: ±1 kV in differential mode, ±2 kV in common mode
Dimensions (H x W x D)	43.6 mm x 442.0 mm x 310.0 mm (1.72 in. x 17.4 in. x 12.2 in.)
Weight (with packaging)	3.6 kg (7.94 lb)
Stack ports	Not supported
RTC	Not supported
RPS	Not supported
PoE	Not supported
Rated voltage range	100 V AC to 240 V AC, 50/60 Hz -48 V DC to -60 V DC
Maximum voltage range	90 V AC to 264 V AC, 47 Hz to 63 Hz -36 V DC to -72 V DC
Maximum power consumption (100% throughput, full speed of fans)	34.1 W
Typical power consumption (30% of traffic load) Tested according to ATIS standard EEE enabled No PoE power consumption	33.4 W
Operating temperature	0°C to 45°C (32°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).
Storage temperature	Pluggable modules not configured: -40°C to +70°C (-40°F to +158°F) Power modules configured: -40°C to +70°C (-40°F to +158°F) Lithium battery modules configured: -20°C to +60°C (-4°F to +140°F) Lead-acid battery modules configured: The storage temperature is determined according to the storage environment of lead-acid batteries.
Noise under normal temperature (27°C, sound power)	< 46.1 dB(A)
Relative humidity	5% to 95%, noncondensing
Operating altitude	DC power modules configured: 0-2000 m (0-6562 ft.) AC power modules or battery modules configured: 0-5000 m (0-16404 ft.)
Certification	EMC certification Safety certification Manufacturing certification
Part number	98010511

Translation

简体中文

Download

Updated: 2023-06-15

Document ID: EDOC1000013597

Downloads: 43562

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate