Version Mapping
Table 4-1190 lists the mapping between the S5731-S24T4X chassis and software versions.
Table 4-1190 Version mappingSeries
|
Model
|
Software Version
|
S5731-S
|
S5731-S24T4X
|
02353AHU: V200R019C00 and later versions
02353AHU-001: V200R020C10 and later versions
|
Appearance and Structure
Figure 4-474 S5731-S24T4X (02353AHU) appearance![]()
Figure 4-475 S5731-S24T4X (02353AHU-001) appearance![]()
1
|
Twenty-four 10/100/1000BASE-T ports
|
2
|
Four 10GE SFP+ ports
Applicable modules and cables:
|
3
|
One console port
|
4
|
One ETH management port
|
5
|
One USB port
|
6
|
One PNP button
NOTICE: To restore the factory settings and reset the switch, hold down the button for at least 6 seconds.
To reset the switch, press the button.
Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.
|
7
|
Ground screw
|
8
|
Fan module slot 1
|
9
|
Fan module slot 2
|
10
|
Power module slot 1
|
11
|
Power module slot 2
|
-
|
-
|
Port Description
10/100/1000BASE-T port
A 10/100/1000BASE-T
Ethernet electrical port sends and receives service data at 10/100/1000
Mbit/s, and must use an
Ethernet cable.
Table 4-1191 describes the attributes
of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-1191 Attributes of a 10/100/1000BASE-T Ethernet electrical port
Attribute
|
Description
|
Connector type
|
RJ45
|
Standards compliance
|
IEEE802.3, IEEE802.3u, IEEE802.3ab
|
Working mode
|
10/100/1000 Mbit/s auto-sensing
|
Maximum transmission distance
|
100 m
|
10GE SFP+ optical port
A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s.
Table 4-1192 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 4-1192 Attributes of a 10GE SFP+ portAttribute
|
Description
|
Connector type
|
LC/PC
|
Optical port attributes
|
Depend on the optical module used
|
Standards compliance
|
IEEE802.3ae
|
Working mode
|
GE/10GE auto-sensing
|
Console port
The console port is connected
to a console for on-site configuration. The port must use a
console cable. The console port is
used when a switch is powered on for the first time. For details about
the attributes of a console port, see
Table 4-1193.
Table 4-1193 Attributes of a console port
Attribute
|
Description
|
Connector type
|
RJ45
|
Standards compliance
|
RS-232
|
Working mode
|
Duplex Universal Asynchronous Receiver/Transmitter (UART)
|
Baud rate
|
9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200
bit/s
Default value: 9600 bit/s
|
ETH management port
You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an
Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port.
Table 4-1194 describes the attributes of an ETH management port.
Table 4-1194 Attributes of an ETH management portAttribute
|
Description
|
Connector type
|
RJ45
|
Standards compliance
|
IEEE802.3
|
Working Mode
|
10/100 Mbit/s auto-sensing
|
Maximum transmission distance
|
100 m
|
In V200R012C00 and later versions, you can log in to the switch that contains the ETH management port for the first time through the ETH port. For details, see "First Login to a Switch" in the
Configuration Guide - Basic Configuration. If you have logged in to the switch for the first time by pressing and holding the MODE button for 6 seconds or longer and saved the configuration, the default configuration on the ETH port will be cleared. In this case, you cannot log in to the switch for the first time through the ETH port. You are advised to log in to the switch for the first time through the ETH port.
USB port
The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.
USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.
Indicator Description
The S5731-S24T4X has similar indicators to those on the S5731-S48P4X except that the S5731-S24T4X does not have a PoE mode indicator. For details, see Indicator Description.
Power Supply Configuration
The switch can use a single power module or double power modules for 1+1 power redundancy. Pluggable AC and DC power modules can be used together in the same switch. However, the power modules with natural heat dissipation and the power modules with fan cannot be used at the same time.
Heat Dissipation
The S5731-S24T4X uses pluggable fan modules for forced air cooling. Air flows in from the front side and exhausts from the rear panel.
![]()
This figure only shows the airflow direction and does not depict the actual device.
Technical Specifications
Table 4-1195 lists technical specifications of the S5731-S24T4X.
Table 4-1195 Technical specificationsItem
|
Description
|
Memory (RAM)
|
2 GB
|
Flash
|
1 GB in total. To view the available flash memory size, run the display version command.
|
Mean time between failures (MTBF)
|
57.73 years
|
Mean time to repair (MTTR)
|
2 hours
|
Availability
|
> 0.99999
|
Service port surge protection
|
Common mode: ±6 kV
|
Power supply surge protection
|
- Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode
- Using DC power modules: ±2 kV in differential mode, ±4 kV in common mode
|
Dimensions (H x W x D)
|
- Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.)
- Maximum dimensions (the depth is the distance from ports on the front panel to the handle on the rear panel): 43.6 mm x 442.0 mm x 448.0 mm (1.72 in. x 17.4 in. x 17.7 in.)
|
Weight (with packaging)
|
8.4 kg (18.52 lb)
|
Stack ports
|
10GE SFP+ ports on the front panel
|
RTC
|
Supported
|
RPS
|
Not supported
|
PoE
|
Not supported
|
Rated voltage range
|
- AC input: 100 V AC to 240 V AC, 50/60 Hz
- High-Voltage DC input: 240 V DC
- DC input: -48 V DC to -60 V DC
|
Maximum voltage range
|
- AC input: 90 V AC to 290 V AC, 45 Hz to 65 Hz
- High-Voltage DC input: 190 V DC to 290 V DC
- DC input: -38.4 V DC to -72 V DC
|
Maximum power consumption (100% throughput, full speed of fans)
|
114 W
|
Typical power consumption (30% of traffic load, tested according to ATIS standard)
|
88 W
|
Operating temperature
|
-5°C to +45°C (23°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).
The switch cannot be started when the ambient temperature is lower than 0°C (32°F).
|
Storage temperature
|
-40°C to +70°C (-40°F to +158°F)
|
Noise under normal temperature (27°C, sound power)
|
< 57.5 dB(A)
|
Relative humidity
|
5% to 95%, noncondensing
|
Operating altitude
|
0-5000 m (0-16404 ft.)
|
Certification
|
- EMC certification
- Safety certification
- Manufacturing certification
|
Part number
|
02353AHU
02353AHU-001
|