No relevant resource is found in the selected language.
Enterprise
Worldwide
Search
Support Documentation
S5700 Series Switches Hardware Description (V200)
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
S5710-108C-PWR-HI

S5710-108C-PWR-HI

Version Mapping

Table 4-998 lists the mapping between the S5710-108C-PWR-HI chassis and software versions.

Table 4-998 Version mapping

Series

Model

Software Version

S5710-HI

S5710-108C-PWR-HI

V200R003C00 to V200R005C03

NOTE:

This model does not match V200R003C02, V200R003C10, or V200R005C01.

Appearance and Structure

Figure 4-398 S5710-108C-PWR-HI appearance

1

Forty-eight PoE+ 10/100/1000BASE-T ports

2

Eight 10GE SFP+ ports

Applicable modules and cables:

3

Front card slot 1

NOTE:

Card supported:

4

Front card slot 2

NOTE:

Card supported:

5

Front card slot 3

NOTE:

Card supported:

6

One console port

7

One ETH management port

8

One USB port

9

Fan slot 1

NOTE:

Applicable fan module: FAN-40EA-B Fan Module

10

Fan slot 2

NOTE:

Applicable fan module: FAN-40EA-B Fan Module

11

Fan slot 3

NOTE:

Applicable fan module: FAN-40EA-B Fan Module

12

Fan slot 4

NOTE:

Applicable fan module: FAN-40EA-B Fan Module

13

Power module slot 1

NOTE:
Applicable power modules:

14

Power module slot 2

NOTE:
Applicable power modules:

15

Ground screw

NOTE:
It is used with a ground cable.

16

ESN label

NOTE:

You can draw it out to view the ESN and MAC address of the switch.

17

Rear card slot

NOTE:

Card supported:

-

-

Port Description

10/100/1000BASE-T port

A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-999 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-999 Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3, IEEE802.3u, IEEE802.3ab

Working mode

10/100/1000 Mbit/s auto-sensing

Maximum transmission distance

100 m

10GE SFP+ port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-1000 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 4-1000 Attributes of a 10GE SFP+ port

Attribute

Description

Connector type

LC/PC

Optical port attributes

Depend on the optical module used

Standards compliance

IEEE802.3ae

Working mode

GE/10GE auto-sensing

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-1001.
Table 4-1001 Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For details on how to use the ETH management port, see the Configuration Guide - Basic Configurations. Table 4-1002 describes the attributes of an ETH management port.
Table 4-1002 Attributes of an ETH management port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3

Working mode

10/100 Mbit/s auto-sensing

Maximum transmission distance

100 m

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

Figure 4-399 Indicators on the S5710-108C-PWR-HI front panel

Figure 4-400 Indicators on the S5710-108C-PWR-HI rear panel

Table 4-1003 Description of indicators on the switch

Number

Indicator

Color

Description

1

SYS: system status indicator

-

Off: The system is not running.

Green
  • Fast blinking: The system is starting.
  • Slow blinking: The system is running properly.

Red

Steady on: The system does not work normally after registration, or a fan or temperature alarm has been generated.

2

MST: stack master/slave indicator

NOTE:

Versions prior to V200R005C03 do not support the stacking function.

-

Off: The switch is the standby or slave switch in a stack or a standalone switch with the stacking function disabled.

Green

Steady on: The switch is the master switch in a stack or a standalone switch with the stacking function enabled.

3

STAT: status indicator

Green

  • Off: The status mode is not selected.

  • Steady on: The service port indicators are in the status mode (default).

4

SPED: speed indicator

Green

  • Off: The speed mode is not selected.

  • Steady on: The service port indicators show the port speed. After 45 seconds, the service port indicators automatically restore to the status mode.

5

STCK: stack indicator

NOTE:

Versions prior to V200R005C03 do not support the stacking function.

Green

If you are not changing the indicator mode (default state):

  • Off: The switch is the standby or slave switch in a stack or a standalone switch with the stacking function disabled.

  • Blinking: The switch is the master switch in a stack or a standalone switch with the stacking function enabled.
If you are changing the indicator mode:
  • Off: The stack mode is not selected.

  • Steady on: The switch is a standby or slave switch in a stack, and the service port indicators show the stack ID of the switch.

  • Blinking: The switch is the master switch in a stack or a standalone switch, and the service port indicators show the stack ID of the master switch.

After 45 seconds, the service port indicators automatically restore to the status mode.

6

PoE: PoE indicator

Green
  • Off: The PoE mode is not selected.
  • Steady on: The service port indicators show the PoE status. After 45 seconds, the service port indicators automatically restore to the status mode.

7

MODE: mode switch button

-
  • When you press this button once, the service port indicators change to the speed mode and show the speed of each service port.
  • When you press this button a second time, the service port indicators change to the stack mode and show the stack ID of the local switch.
  • When you press this button a third time, the service port indicators change to PoE mode and show the PoE status of ports.
  • When you press this button a fourth time, the service port indicators restore to the default mode, and the STAT indicator turns green.

If you do not press the MODE button within 45 seconds, the service port indicators restore to the default mode. In this case, the STAT indicator is steady green, the SPED and PoE indicators are off, and the STCK indicator is off or blinking green.

ID: ID indicator

NOTE:

The S5710-108C-PWR-HI of V200R003 does not support the ID indicator.

Blue
  • Off: The ID indicator is not used (default state).
  • Steady on: The indicator identifies the device for maintenance. The ID indicator can be turned on or off remotely to help onsite engineers find the device to maintain.

8

Service port indicator (GE electrical port)

Meanings of service port indicators vary in different modes. For details, see Table 4-1004.

9

Service port indicator (10GE optical port)

10

USB-based deployment indicator: ACT

-

Off:

  • No USB flash drive is connected to the switch.
  • The USB port is damaged.
  • The ACT indicator is damaged.
  • The USB flash drive connected to the switch does not contain any configuration file.
  • The switch is restarting after a USB-based upgrade.

Green

  • Steady on: A USB-based deployment has been completed.

  • Blinking: The system is reading data from the USB flash drive.

Yellow

NOTE:

This indicator state is available in V200R005C00 and later versions.

Steady on: The switch has copied all the required files and completed the file check. The USB flash drive can be removed from the switch.

Red

Blinking: An error has occurred when the system is executing the configuration file or reading data from the USB flash drive.

11

Management port indicator: L/A

Green
  • Off: No link is established on the management port.
  • Steady on: A link is established on the management port.
  • Blinking: The management port is sending or receiving data.
Table 4-1004 Description of service port indicators in different modes

Display Mode

Color

Description

Status

-

Off: No link is established on the port or the port has been shut down.

Green (electrical port)

  • Steady on: A link is established on the port.

  • Blinking: The port is sending or receiving data.

Green (optical port)

Steady on: A link is established on the port.

Yellow (optical port)

Blinking: The port is sending or receiving data.

Speed

Green
  • Off: No link is established on the port or the port has been shut down.

  • Steady on:

    10M/100M/1000M port: The port is operating at 10/100 Mbit/s.

    1000M/10GE port: The port is operating at 1000 Mbit/s.

  • Blinking:

    10M/100M/1000M port: The port is operating at 1000 Mbit/s.

    1000M/10GE port: The port is operating at 10 Gbit/s.

PoE

Green
  • Off: The port is not providing power to a powered device (PD).

  • Steady on: The port is providing PoE power.

  • Blinking: The PD connected to the port is not a standard PD or its power exceeds the maximum power or power threshold of the port.

Stack

Green
  • Off: Port indicators do not show the stack ID of the switch.

  • If the indicator is steady on, the switch is not a master switch:

    • If the indicator of a port is steady on, the number of this port is the stack ID of the switch.

    • If the indicators of ports 1 to 9 are steady on, the stack ID of the switch is 0.

  • If the indicator is blinking, the switch is a master switch:

    • If the indicator of a port is blinking, the number of this port is the stack ID of the switch.

    • If the indicators of ports 1 to 9 are blinking, the stack ID of the switch is 0.

Power Supply Configuration

The S5710-108C-PWR-HI is a PoE switch and uses 1150 W AC PoE power modules. It has two power module slots. Table 4-1005 lists its power supply configurations.

Table 4-1005 Power supply configurations

Power Module 1

Power Module 2

Available PoE Power

Maximum Number of Ports (Fully Loaded)

1150 W (220 V)

–

785.4 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 26

1150 W (220 V)

1150 W (220 V)

1440 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 48

1150 W (110 V)

–

446.6 W
  • 802.3af (15.4 W per port): 29
  • 802.3at (30 W per port): 14

1150 W (110 V)

1150 W (110 V)

893.2 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 29

When a switch has two power modules installed, the two power modules work in redundancy mode to provide power for the chassis and in load balancing mode to provide power for PDs.

Figure 4-401 shows the power supply mode of dual AC PoE power modules (PWR1 and PWR2). After AC power is transmitted to the PWR modules, the PWR modules provide 12 V and -53 V outputs. The outputs are combined on the motherboard, which then provides 12 V voltage for the switch and -53 V voltage for the PDs.
Figure 4-401 Power supply by dual AC PoE power modules

L: live wire

N: neutral wire

PGND: protection ground wire

GND: 12 V reference ground

RTN: -53 V reference ground

When using non-PoE power modules, the S5710-108C-PWR-HI can be configured with a single power module or double power modules for 1+1 power redundancy. Currently, only one non-PoE power module model, a 350 W AC power module, is supported.

Figure 4-402 shows the power supply connections of dual AC power modules. After AC power is transmitted to the PWR module, the PWR module provides 12 V output voltage, and the motherboard provides power for the entire device.
Figure 4-402 Power supply connections of dual AC power modules

L: Live wire

N: Neutral wire

PGND: Protection ground wire

GND: 12 V reference ground

Heat Dissipation

The S5710-108C-PWR-HI uses pluggable fan modules for forced air cooling. The airflow direction is front-to-rear.

A little air also enters the chassis from both sides of the chassis.

Technical Specifications

Table 4-1006 lists technical specifications of the S5710-108C-PWR-HI.

Table 4-1006 Technical specifications

Item

Description

Memory (RAM)

1 GB

Flash

200 MB

Mean time between failures (MTBF)

28.16 years when no interface card is configured, 27 years when a 16-port GE optical card is configured, 25.98 years when a 16-port GE electrical card is configured, 26.95 years when a 4-port 10GE card is configured, 26.69 years when a 4-port 40GE card is configured.

Mean time to repair (MTTR)

2 hours

Availability

> 0.99999

Service port surge protection

Common mode: ±1 kV

Power supply surge protection

±2 kV in differential mode, ±4 kV in common mode

Dimensions (H x W x D)

86.1 mm x 442.0 mm x 470.0 mm (3.4 in. x 17.4 in. x 18.5 in.)

When 1150 W power modules are installed, they stretch out from the chassis. Therefore, the total depth of the switch changes to 557.3 mm (21.94 in.).

Weight
  • Empty: ≤ 12 kg (26.46 lb)
  • Fully configured: ≤ 18 kg (39.68 lb)

Stack ports
  • V200R005C03 and earlier version: not supported
  • V200R005C03: 8-port 10GE SFP+ ports on the front panel

RPS

Not supported

PoE

Supported

Rated voltage range

100 V AC to 240 V AC, 50/60 Hz

Maximum voltage range

90 V AC to 264 V AC, 47 Hz to 63 Hz

Maximum power consumption (100% throughput, 100% PoE loads, full speed of fans)
  • Using 350 W power modules: 240 W
  • Using two 1150 W power modules: 1680 W (system power consumption: 240 W, PoE: 1440 W)

Operating temperature

0°C to 45°C (32°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.)

NOTE:

When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 67.3 dB(A)

Relative humidity

5% to 95%, noncondensing

Operating altitude

0-5000 m (0-16404 ft.)

Certification
  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

02354043
Translation
简体中文
Download
Updated: 2023-06-15

Document ID: EDOC1000013597

Views: 4868689

Downloads: 43562

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Digital Signature File

Digital Signature Authentication Mode
Share
Previous Next

Copyright © 2023 Huawei Technologies Co., Ltd. All rights reserved.

You are going to visit :