No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S5700 Series Switches Hardware Description

This document provides an overall description of the S5700 hardware, helping you obtain detailed information about each chassis, card, power module, fan module, cable, and optical module.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
S5710-52C-PWR-EI

S5710-52C-PWR-EI

Version Mapping

Table 4-761 lists the mapping between the S5710-52C-PWR-EI chassis and software versions.

Table 4-761 Version mapping

Series

Model

Software Version
S5710-EI S5710-52C-PWR-EI

V200R002C00 to V200R005C02

NOTE:
This model does not match V200R003C02, V200R003C10, or V200R005C01.

Appearance and Structure

Figure 4-304 S5710-52C-PWR-EI appearance
1 Forty-eight PoE+ 10/100/1000BASE-T ports 2 Four 10GE SFP+ ports
3 One ETH management port 4 One mini USB port
5 One console port 6 One USB port
7 Ground screw
NOTE:
It is used with a ground cable.
8 Rear card slot 1
9 Rear card slot 2 10 ESN label
NOTE:

You can draw it out to view the ESN and MAC address of the switch.

11 Power module slot 2
NOTE:
12 Power module slot 1
NOTE:

Port Description

10/100/1000BASE-T port
A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-762 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-762 Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3, IEEE802.3u, IEEE802.3ab

Working mode

10/100/1000 Mbit/s auto-sensing

Maximum transmission distance

100 m

10GE SFP+ port
A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-763 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 4-763 Attributes of a 10GE SFP+ port

Attribute

Description

Connector type

LC/PC

Optical port attributes

Depend on the optical module used

Standards compliance

IEEE802.3ae

Working mode

GE/10GE auto-sensing

Console port
The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-764.
Table 4-764 Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

Mini USB port

The mini USB port is connected to a console for on-site configuration. When both the Mini USB and console port have a cable connected, only the Mini USB port works.

ETH management port
You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For details on how to use the ETH management port, see the Configuration Guide - Basic Configurations. Table 4-765 describes the attributes of an ETH management port.
Table 4-765 Attributes of an ETH management port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3

Working mode

10/100 Mbit/s auto-sensing

Maximum transmission distance

100 m

USB port
The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.
NOTE:
USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5710-52C-PWR-EI has the same types of indicators as the S5710-28C-PWR-EI-AC. For details, see Indicator Description.

Power Supply Configuration

The S5710-52C-PWR-EI is a PoE switch and uses 580 W or 1150 W AC PoE power modules. It has two power module slots. Table 4-766 lists its power supply configurations.

Table 4-766 Power supply configurations
Power Module 1 Power Module 2 Available PoE Power Maximum Number of Ports (Fully Loaded)
580 W 369.6 W
  • 802.3af (15.4 W per port): 24
  • 802.3at (30 W per port): 12
580 W 580 W 739.2 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 24
1150 W 785.4 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 26
1150 W 1150 W 1440 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 48
NOTE:
When a switch has two power modules installed, the two power modules work in redundancy mode to provide power for the chassis and in load balancing mode to provide power for PDs.
Figure 4-305 shows the power supply mode of dual AC PoE power modules (PWR1 and PWR2). After AC power is transmitted to the PWR modules, the PWR modules provide 12 V and -53 V outputs. The outputs are combined on the motherboard, which then provides 12 V voltage for the switch and -53 V voltage for the PDs.
Figure 4-305 Power supply by dual AC PoE power modules

L: live wire

N: neutral wire

PGND: protection ground

GND: 12 V reference ground

RTN: -53 V reference ground

Heat Dissipation

The S5710-52C-PWR-EI has five built-in fans for forced air cooling. The airflow direction is left-to-right.

NOTE:
This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-767 lists technical specifications of the S5710-52C-PWR-EI.

Table 4-767 Technical specifications

Item

Description

Memory (RAM)

512 MB

Flash

200 MB

Mean time between failures (MTBF)

36.86 years when an 8-port GE optical card is configured, 36.35 years when an 8-port GE electrical card is configured, 35.27 years when a 2-port 10GE interface card is configured

Mean time to repair (MTTR)

2 hours

Availability

> 0.99999

Service port surge protection

Common mode: ±1 kV

Power supply surge protection

  • Using 580 W AC power modules: ±6 kV in differential mode, ±6 kV in common mode
  • Using 1150 W AC power modules: ±2 kV in differential mode, ±4 kV in common mode

Dimensions (H x W x D)

44.4 mm x 442.0 mm x 420.0 mm (1.75 in. x 17.4 in. x 16.5 in.)

When 1150 W power modules are installed, they stretch out from the chassis. Therefore, the total depth of the switch changes to 507.3 mm (19.97 in.).

Weight

  • Empty: ≤ 6 kg (13.23 lb)
  • Fully configured: ≤ 10 kg (22.05 lb)

Stack ports

Four fixed 10GE SFP+ ports on the front panel or ports on the 2-port 10GE rear card

RPS

Not supported

PoE

Supported

Rated voltage range

100 V AC to 240 V AC, 50/60 Hz

Maximum voltage range

90 V AC to 264 V AC, 47 Hz to 63 Hz

Maximum power consumption (100% throughput, 100% PoE loads, full speed of fans)

Using two 580 W power modules

  • No card: 1023 W (system power consumption: 283 W, PoE: 740 W)
  • Two 8-port GE electrical card: 1035 W (system power consumption: 295 W, PoE: 740 W)
  • Two 8-port GE optical card: 1043 W (system power consumption: 303 W, PoE: 740 W)
  • Two 2-port 10GE optical card: 1040 W (system power consumption: 300 W, PoE: 740 W)

Using two 1150 W power modules

  • No card: 1605 W (system power consumption: 165 W, PoE: 1440 W)
  • Two 8-port GE electrical card: 1625 W (system power consumption: 185 W, PoE: 1440 W)
  • Two 8-port GE optical card: 1635 W (system power consumption: 195 W, PoE: 1440 W)
  • Two 2-port 10GE optical card: 1633 W (system power consumption: 193 W, PoE: 1440 W)

Operating temperature

0°C to 50°C (32°F to 122°F) at an altitude of 0-1800 m (0-5906 ft.)

NOTE:

When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 60 dB(A)

Relative humidity

5% to 95%, noncondensing

Operating altitude

0-5000 m (0-16404 ft.)

Certification

  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

02355886
Translation
Download
Updated: 2019-08-19

Document ID: EDOC1000013597

Views: 563877

Downloads: 14373

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next