No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S5700 Series Switches Hardware Description

This document provides an overall description of the S5700 hardware, helping you obtain detailed information about each chassis, card, power module, fan module, cable, and optical module.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
S5700-28X-LI-24S-AC

S5700-28X-LI-24S-AC

Version Mapping

Table 4-84 lists the mapping between the S5700-28X-LI-24S-AC chassis and software versions.

Table 4-84  Version mapping

Series

Model

Software Version
S5700-LI S5700-28X-LI-24S-AC

V200R003C00 to V200R012C00 versions

NOTE:
This model does not match V200R003C02, V200R003C10, V200R005C00SPC500, V200R005C01, V200R005C02, V200R005C03, or V200R007C10.

Appearance and Structure

Figure 4-33  S5700-28X-LI-24S-AC appearance
1 Twenty 100/1000BASE-X ports 2 Four combo ports (10/100/1000BASE-T + 100/1000BASE-X)
3 Four 10GE SFP+ ports 4 One mini USB port
5 One console port 6 One USB port
7 Ground screw
NOTE:
It is used with a ground cable.
8 AC socket
NOTE:

It is used with an AC power cable.

9 Jack for AC power cable locking strap
NOTE:
The AC power cable locking strap is not delivered with the switch.
10 RPS socket
NOTE:

It is used with an RPS cable, which is not hot swappable.

Port Description

100/1000BASE-X port
A 100/1000BASE-X port can send and receive data at 100 Mbit/s or 1000 Mbit/s. Table 4-85 describes the attributes of a 100/1000BASE-X port.
Table 4-85  Attributes of a 100/1000BASE-X port

Attribute

Description

Connector type

LC/PC

Optical interface attributes

Depend on the optical module used

Standards compliance

IEEE802.3z

Working mode

100/1000 Mbit/s auto-sensing

Combo port
A combo port refers to a pair of ports consisting of an optical Ethernet port and an electrical Ethernet port on the panel. Each combo port matches only one internal forwarding port. A combo port can be configured as an electrical port or an optical port, but only one port can be active at a time. When one port is active, the other port is shut down.
NOTE:

By default, a combo port works in auto mode, in which the port type is determined as follows:

  • If the optical port has no optical module installed and the electrical port has no Ethernet cable connected, the port type depends on which port is connected first. If the electrical port is connected by an Ethernet cable first, the electrical port is used for data switching. If the optical port has an optical module installed first, the optical port is used for data switching.
  • If the electrical port has an Ethernet cable connected and is in Up state, the electrical port is still used for data switching when the optical port has an optical module installed.
  • If the optical port, no matter in Up or Down state, has an optical module installed, the optical port is still used for data switching when the electrical port has an Ethernet cable connected.
  • If the optical port has an optical module installed and the electrical port has an Ethernet cable connected, the optical port is used for data switching after the switch restarts.
You can configure a combo port as an electrical or optical port using the combo-port command.
10GE SFP+ port
A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-86 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 4-86  Attributes of a 10GE SFP+ port

Attribute

Description

Connector type

LC/PC

Optical port attributes

Depend on the optical module used

Standards compliance

IEEE802.3ae

Working mode

GE/10GE auto-sensing

Console port
The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-87.
Table 4-87  Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

Mini USB port

The mini USB port is connected to a console for on-site configuration. When both the Mini USB and console port have a cable connected, only the Mini USB port works.

USB port
The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB flash drive used on a switch must comply with USB 1.1.
NOTE:
USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

NOTE:
In V200R007 and later versions, you can hold down the mode switch button for 6s and release it to start the web initial login mode. Either of the following situations will occur:
  • If the switch has no configuration file, the system attempts to enter the web initial login mode. In this mode, the status of mode indicators is as follows:
    • If the system enters the web initial login mode successfully, all mode indicators turn green and stay on for a maximum of 10 minutes.
    • If the system fails to enter the initial login mode, all mode indicators fast blink for 10 seconds and then restore to the default status.
  • If the switch has a configuration file, the system cannot enter the web initial login mode. In this case, all mode indicators fast blink for 10s, and then return to the default states.
Figure 4-34  Indicators on the S5700-28X-LI-24S-AC

NOTE:

The S5701-28X-LI-24S-AC, S5700-28X-LI-24S-AC, and S5700-28X-LI-24S-DC have air holes above the 24 optical ports for heat dissipation (numbered 11 in Figure 4-34). The indicators for the service ports are numbered 8 in Figure 4-34.

Table 4-88  Description of indicators on the switch

Number

Indicator/Button

Color

Description

1

PWR: internal power supply indicator

-

Off: The switch is powered off.

Green

Steady on: The switch is powered on.

Yellow

Steady on: The built-in power module is faulty, and the switch is powered by the RPS system.

2

RPS: RPS power supply indicator

-

Off: No RPS is connected to the switch.

Green

  • Steady on: The RPS is in cold backup state.

  • Blinking: The RPS is providing power for another device.

Yellow

Blinking: The RPS is providing power for the switch and the built-in power module of the switch is faulty.

3

SYS: system status indicator

-

Off: The system is not running.

Green

  • Fast blinking: The system is starting or is copying the system software and configuration file from a USB flash drive during a USB-based upgrade.
  • Slow blinking: The system is running normally.

Yellow

Blinking: The switch has restarted after a successful upgrade using a USB flash drive. You can remove the USB flash drive from the switch.

Red

  • Steady on: The system does not work normally after registration, or a fan or temperature alarm has been generated.

  • Blinking: The system cannot be upgraded after a USB flash drive is inserted. The USB-based upgrade failed.
4

STAT: status indicator

Green

  • Off: The status mode is not selected.

  • Steady on: The status mode (default mode) is selected. If the status mode is selected, the service port indicator shows the port link or activity state.
5

SPED: speed indicator

Green

  • Off: The speed mode is not selected.

  • Steady on: The speed mode is selected. If the speed mode is selected, the service port indicator shows the port speed state. After 45 seconds, the service port indicators automatically restore to the status mode.

6

STCK: stack indicator

Green

If you are not changing the indicator mode (default):
  • Off: The switch is in stack standby or slave state or the stacking function is not enabled on the switch.
  • Blinking: The switch is a stack master switch or a standalone switch with the stacking function enabled.

If you are changing the indicator mode:
  • Off: The stack mode is not selected.
  • Steady on: The switch is a standby or slave switch in a stack, and the service port indicators show the stack ID of the switch.

  • Blinking: The switch is the master switch in a stack or a standalone switch, and the service port indicators show the stack ID of the master switch.

After 45 seconds, the service port indicators automatically restore to the status mode.
7

MODE: mode switch button

-

  • When you press this button once, the service port indicators change to the speed mode and show the speed of each service port.
  • When you press this button a second time, the service port indicators change to the stack mode and show the stack ID of the local switch.
  • When you press this button a third time, the service port indicators restore to the default mode, and the STAT mode turns green.

If you do not press the MODE button within 45 seconds, the service port indicators restore to the default mode. In this case, the STAT indicator is steady green, the SPED indicator is off, and the STCK indicator is off or blinking green.

8

Service port indicator

NOTE:

Arrowheads show the positions of ports. A down arrowhead indicates a port at the bottom, and an up arrowhead indicates a port at the top.

Meanings of service port indicators vary in different modes. For details, see Table 4-89 and Table 4-90.

9

Mini USB indicator

Green

  • Off: The Mini USB port is not active, and the console port is active.

  • Steady on: The Mini USB port is active.

When this indicator is on, the console indicator is off.

10

Console indicator

Green

  • Off: The console port is not active, and the Mini USB port is active.

  • Steady on (default): The console port is active.

When this LED is on, the Mini USB port indicator is off.

Table 4-89  Description of service port indicators in different modes (two indicators for each port)
Display Mode Color Status Description
Status - Off The port is not connected or has been shut down.
Green Steady on A link has been established on the port.
Yellow Blinking The port is sending or receiving data.
Speed - Off The port is not connected or has been shut down.
Green and yellow Steady on

10M/100M/1000M port: The port is operating at 10/100 Mbit/s.

1000M/10GE port: The port is operating at 1000 Mbit/s.

Green and yellow Blinking

10M/100M/1000M port: The port is operating at 1000 Mbit/s.

1000M/10GE port: The port is operating at 10 Gbit/s.

Stack - Off Port indicators do not show the stack ID of the switch.
Green and yellow Steady on
The switch is not the master switch in a stack.
  • If the indicator of a port is steady on, the number of this port is the stack ID of the switch.

  • If the indicators of ports 1 to 9 are steady on, the stack ID of the switch is 0.

Green and yellow Blinking
The switch is the master switch in a stack.
  • If the indicator of a port is blinking, the number of this port is the stack ID of the switch.

  • If the indicators of ports 1 to 9 are blinking, the stack ID of the switch is 0.

Table 4-90  Description of service port indicators in different modes (one indicator for each port)
Display Mode Color Status Description
Status - Off The port is not connected or has been shut down.
Green Steady on A link has been established on the port.
Green Blinking The port is sending or receiving data.
Speed - Off The port is not connected or has been shut down.
Green Steady on

10M/100M/1000M port: The port is operating at 10/100 Mbit/s.

1000M/10GE port: The port is operating at 1000 Mbit/s.

Green Blinking

10M/100M/1000M port: The port is operating at 1000 Mbit/s.

1000M/10GE port: The port is operating at 10 Gbit/s.

Stack - Off Port indicators do not show the stack ID of the switch.
Green Steady on
The switch is not the master switch in a stack.
  • If the indicator of a port is steady on, the number of this port is the stack ID of the switch.

  • If the indicators of ports 1 to 9 are steady on, the stack ID of the switch is 0.

Green Blinking
The switch is the master switch in a stack.
  • If the indicator of a port is blinking, the number of this port is the stack ID of the switch.

  • If the indicators of ports 1 to 9 are blinking, the stack ID of the switch is 0.

Power Supply Configuration

The S5700-28X-LI-24S-AC has a built-in power module and does not support pluggable power modules. It can connect to an RPS1800 power supply for power redundancy.

Figure 4-35 shows the power supply mode of a built-in AC power module. The built-in AC power module (PWR) receives power from an external power source and provides a 12 V output to the chassis.
Figure 4-35  Power supply mode of a built-in AC power module

L: live wire

N: neutral wire

PGND: protection ground

GND: 12 V reference ground

Heat Dissipation

The S5700-28X-LI-24S-AC has two built-in fans for forced air cooling. The airflow direction is left-to-right.

NOTE:
This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-91 lists specifications of the S5700-28X-LI-24S-AC.

Table 4-91  Technical specifications

Item

Description

Memory (RAM)

256 MB

Flash

200 MB

Mean time between failures (MTBF)

89.91 years

Mean time to repair (MTTR)

2 hours

Availability

> 0.99999

Service port surge protection

Common mode: ±6 kV

Power supply surge protection

±6 kV in differential mode, ±6 kV in common mode

Dimensions (W x D x H)

442.0 mm x 220.0 mm x 43.6 mm (17.4 in. x 8.7 in. x 1.72 in.)

Weight (including packaging materials)

3.5 kg (7.72 lb)

Stack ports

Four uplink 10GE SFP+ ports

RTC

Supported

RPS

Supported

PoE

Not supported

Rated voltage range

100 V AC to 240 V AC, 50/60 Hz

Maximum voltage range

90 V AC to 264 V AC, 47 Hz to 63 Hz

Maximum power consumption (100% throughput, full speed of fans)

60 W

Typical power consumption (30% of traffic load)
  • Tested according to ATIS standard
  • EEE enabled
  • No PoE power consumption

49.7 W

Operating temperature

0°C to 45°C (32°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.)
NOTE:

When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 49.6 dB(A)

Relative humidity

5% to 95%, noncondensing

Operating altitude

0-5000 m (0-16404 ft.)

Certification

  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

02355271
Translation
Download
Updated: 2019-05-16

Document ID: EDOC1000013597

Views: 372047

Downloads: 12061

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next