No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S5700 Series Switches Hardware Description

This document provides an overall description of the S5700 hardware, helping you obtain detailed information about each chassis, card, power module, fan module, cable, and optical module.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ES5D00ETPC00 (Stack Rear Card)

ES5D00ETPC00 (Stack Rear Card)

Version Mapping

Table 8-155 lists the mapping between the ES5D00ETPC00 card and software versions.

Table 8-155  Version mapping

Card Model

Software Version
ES5D00ETPC00
NOTE:
After the display device command is executed, the PCB model of the card is displayed as CX22ETPC.
V100R005C01 to V200R005C03
NOTE:
This module is not supported in V200R003C02 or V200R003C10.

Card Overview

Intelligent Stack (iStack) technology enables multiple stacking-capable devices to function as a logical device.

Before a stack is set up, each switch is an independent entity that has its own IP address and MAC address. You need to manage the switches separately. After a stack is set up, switches in the stack form a logical entity that can be managed and maintained using a single IP address. Stack technology improves forwarding performance and network reliability, and simplifies network management.

Switches can be connected as a stack using service ports or stack cards (ES5D00ETPC00).

The ES5D00ETPC00 stack card can be installed in a rear card slot of the switch models listed in Table 8-156.

Table 8-156  Applicable switch models
Card Switch Model
ES5D00ETPC00
  • S5700-24TP-SI-AC
  • S5700-24TP-SI-DC
  • S5700-48TP-SI-AC
  • S5700-48TP-SI-DC
  • S5700-24TP-PWR-SI
  • S5700-48TP-PWR-SI
  • S5700-28C-SI
  • S5700-52C-SI
  • S5700-28C-PWR-SI
  • S5700-52C-PWR-SI
  • S5700-28C-EI
  • S5700-52C-EI
  • S5700-28C-EI-24S
  • S5700-28C-PWR-EI
  • S5700-52C-PWR-EI
  • S5710-28C-LI
  • S5710-52C-LI
  • S5710-28C-PWR-LI
  • S5710-52C-PWR-LI

Figure 8-69 shows the appearance of the ES5D00ETPC00.

Figure 8-69  ES5D00ETPC00

Functions

Table 8-157 describes functions of the ES5D00ETPC00.

Table 8-157  Functions

Function

Description

Basic function

Provides two 12 Gbit/s electrical ports for stacking. The 12 Gbit/s electrical ports on multiple switches are connected using PCIe cables to set up a stack.

Topology Switches in a stack can be connected in a chain or ring topology. A link failure in the chain topology causes the stack to split. In contrast, the ring topology changes into a chain topology upon a link failure so that services in the stack are not affected. Therefore, the ring topology is more reliable than the chain topology. Figure 8-70 and Figure 8-71 show the chain and ring topologies.
NOTE:
When connecting stack cables, connect stack1 port of one switch to stack2 port of another switch.
Figure 8-70  Chain topology of a stack
Figure 8-71  Ring topology of a stack

Usage Constraints

The following requirements must be met to set up a stack:
  • All the member switches belong to the same series. The EI series and SI series cannot form a stack.
  • All switches have stack cards installed and are connected using PCIe cables.
  • The ES5D00ETPC00 is not hot swappable, but PCIe cables are hot swappable.

Port Description

Figure 8-72 shows ports on the ES5D00ETPC00.

Figure 8-72  Ports on the ES5D00ETPC00

1. Two stack electrical ports

Stack electrical port

The ES5D00ETPC00 provides two 12 Gbit/s electrical ports for stacking. The two 12 Gbit/s electrical ports must be used with PCIe Cables. Table 8-158 describes attributes of the 12 Gbit/s electrical port.

Table 8-158  Attributes of a stack electrical port
Attribute Description
Connector type PCIe
Standards compliance IEEE 802.3ae
Frame format Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol IP

Technical Specifications

Table 8-159 lists technical specifications of the ES5D00ETPC00.

Table 8-159  Technical specifications

Item

Description

Physical specifications

  • Dimensions (W x D x H): 143 mm x 126 mm x 43 mm (5.63 in. x 4.96 in. x 1.69 in.)
  • Weight: 0.2 kg (0.44 lb)
  • Maximum power consumption: 0.5 W

Environment specifications

  • Operating temperature: 0°C to 50°C (32°F to 122°F)
  • Relative humidity: 5% to 95%
  • Storage temperature: -40°C to +70°C (-40°F to +158°F)

Ordering Information

Ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 8-160 provides the card ordering information.

Table 8-160  Ordering information

Card Description

Card Name

Part Number
Ethernet Stack Interface Card (Including Stack Card, 100 cm Stack Cable) ES5D001VST00 02319959
Ethernet Stack Interface Card (Including Stack Card, 300 cm Stack Cable) ES5D2VS02000 02310QPL
Translation
Download
Updated: 2019-05-16

Document ID: EDOC1000013597

Views: 415419

Downloads: 12551

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next