No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S5700 Series Switches Hardware Description

This document provides an overall description of the S5700 hardware, helping you obtain detailed information about each chassis, card, power module, fan module, cable, and optical module.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
S5700-52C-PWR-EI

S5700-52C-PWR-EI

Version Mapping

Table 4-732 lists the mapping between the S5700-52C-PWR-EI and software versions.

Table 4-732  Version mapping

Series

Model

Software Version
S5700-EI S5700-52C-PWR-EI

V100R005C01 to V200R005C03

NOTE:
This model does not match V200R003C02 or V200R003C10.

Appearance and Structure

Figure 4-292  S5700-52C-PWR-EI appearance
1 Forty-eight PoE+ 10/100/1000BASE-T ports 2 One console port
3 One ETH management port 4 Front card slot
5 ESD jack
NOTE:

Before installing or maintaining a switch, wear an ESD wrist strap and insert the other end of the ESD wrist strap into this ESD jack.

6 Rear card slot
7 Fan slot
NOTE:

Applicable fan module:

CX7E1FANA fan module

8 Power module slot 2
NOTE:
9 Power module slot 1
NOTE:
- -

Port Description

10/100/1000BASE-T port
A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-733 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-733  Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3, IEEE802.3u, IEEE802.3ab

Working mode

10/100/1000 Mbit/s auto-sensing

Maximum transmission distance

100 m

Console port
The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-734.
Table 4-734  Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

ETH management port
You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For details on how to use the ETH management port, see the Configuration Guide - Basic Configurations. Table 4-735 describes the attributes of an ETH management port.
Table 4-735  Attributes of an ETH management port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3

Working mode

10/100 Mbit/s auto-sensing

Maximum transmission distance

100 m

Indicator Description

The S5700-52C-PWR-EI has the same types of indicators as the S5700-28C-PWR-EI. For details, see Indicator Description.

Power Supply Configuration

The S5700-52C-PWR-EI is a PoE switch. It has two power module slots, each of which can have a 500 W or 250 W power module installed. A power module can provide 369.6 W or 123.2 W of PoE power for powered devices (PDs). Table 4-736 lists its power supply configurations.

Table 4-736  Power supply configurations
Power Module 1 Power Module 2 Available PoE Power Maximum Number of Ports (Fully Loaded)
250 W 123.2 W
  • 802.3af (15.4 W per port): 8
  • 802.3at (30 W per port): 4
500 W 369.6 W
  • 802.3af (15.4 W per port): 24
  • 802.3at (30 W per port): 12
250 W 250 W 246.4 W
  • 802.3af (15.4 W per port): 16
  • 802.3at (30 W per port): 8
500 W 500 W 739.2 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 24
NOTE:
When a switch has two power modules installed, the two power modules work in redundancy mode to provide power for the chassis and in load balancing mode to provide power for PDs.
Figure 4-293 shows the power supply mode of dual AC PoE power modules (PWR1 and PWR2). After AC power is transmitted to the PWR modules, the PWR modules provide 12 V and -53 V outputs. The outputs are combined on the motherboard, which then provides 12 V voltage for the switch and -53 V voltage for the PDs.
Figure 4-293  Power supply by dual AC PoE power modules

L: live wire

N: neutral wire

PGND: protection ground

GND: 12 V reference ground

RTN: -53 V reference ground

Heat Dissipation

The S5700-52C-PWR-EI uses pluggable fan modules for forced air cooling. Air flows in from the left and right sides, and exhausts from the rear panel.

NOTE:
This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-737 lists technical specifications of the S5700-52C-PWR-EI.

Table 4-737  Technical specifications

Item

Description

Memory (RAM)

256 MB

Flash

32 MB

Mean time between failures (MTBF)

44.8 years when a 2-port 10GE interface card is configured, 66.8 years when a 4-port GE front card is configured, 29.89 years when a 4x10GE front card is configured

Mean time to repair (MTTR)

2 hours

Availability

> 0.99999

Service port surge protection

Common mode: ±1 kV

Power supply surge protection

±2 kV in differential mode, ±4 kV in common mode

Dimensions (W x D x H)

442.0 mm x 420.0 mm x 43.6 mm (17.4 in. x 16.5 in. x 1.72 in.)

Weight

  • Empty: ≤ 5 kg (11.02 lb)
  • Fully loaded: ≤ 8.5 kg (18.74 lb)

Stack ports

Two stack ports available on each stack card

RPS

Not supported

PoE

Supported

Rated voltage range

100 V AC to 240 V AC, 50/60 Hz

Maximum voltage range

90 V AC to 264 V AC, 47 Hz to 63 Hz

Maximum power consumption (100% throughput, 100% PoE loads, full speed of fans)

930 W (system power consumption: 190 W, PoE: 740 W)

Operating temperature

0°C to 50°C (32°F to 122°F)

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 45 dB(A)

Relative humidity

5% to 95%, noncondensing

Operating altitude

0-5000 m (0-16404 ft.)

Certification

  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

02352366
Translation
Download
Updated: 2019-05-16

Document ID: EDOC1000013597

Views: 369918

Downloads: 12045

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next