No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


S5700 Series Switches Hardware Description

This document provides an overall description of the S5700 hardware, helping you obtain detailed information about each chassis, card, power module, fan module, cable, and optical module.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).


Version Mapping

Table 4-194 lists the mapping between the S5710-52C-PWR-LI chassis and software versions.

Table 4-194 Version mapping



Software Version
S5710-LI S5710-C-LI S5710-52C-PWR-LI

V200R001C00 only

Appearance and Structure

Figure 4-75 S5710-52C-PWR-LI appearance
1 Forty-eight PoE+ 10/100/1000BASE-T ports 2 One console port
3 One ETH management port 4 One USB port
5 Front card slot 6 ESD jack

Before installing or maintaining a switch, wear an ESD wrist strap and insert the other end of the ESD wrist strap into this ESD jack.

7 Rear card slot 8 Fan slot

Applicable fan module:

CX7E1FANA fan module

9 Power module slot 2
10 Power module slot 1

Port Description

10/100/1000BASE-T port
A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-195 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-195 Attributes of a 10/100/1000BASE-T Ethernet electrical port



Connector type


Standards compliance

IEEE802.3, IEEE802.3u, IEEE802.3ab

Working mode

10/100/1000 Mbit/s auto-sensing

Maximum transmission distance

100 m

Console port
The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-196.
Table 4-196 Attributes of a console port



Connector type


Standards compliance


Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

ETH management port
You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For details on how to use the ETH management port, see the Configuration Guide - Basic Configurations. Table 4-197 describes the attributes of an ETH management port.
Table 4-197 Attributes of an ETH management port



Connector type


Standards compliance


Working mode

10/100 Mbit/s auto-sensing

Maximum transmission distance

100 m

USB port
The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB flash drive used on a switch must comply with USB 1.1.
USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5710-52C-PWR-LI has the same types of indicators as the S5700-28C-PWR-SI. For details, see Indicator Description.

Power Supply Configuration

The S5710-52C-PWR-LI is a PoE switch. It has two power module slots, each of which can have a 500 W or 250 W power module installed. A power module can provide 369.6 W or 123.2 W of PoE power for powered devices (PDs). Table 4-198 lists its power supply configurations.

Table 4-198 Power supply configurations
Power Module 1 Power Module 2 Available PoE Power Maximum Number of Ports (Fully Loaded)
250 W 123.2 W
  • 802.3af (15.4 W per port): 8
  • 802.3at (30 W per port): 4
500 W 369.6 W
  • 802.3af (15.4 W per port): 24
  • 802.3at (30 W per port): 12
250 W 250 W 246.4 W
  • 802.3af (15.4 W per port): 16
  • 802.3at (30 W per port): 8
500 W 500 W 739.2 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 24
When a switch has two power modules installed, the two power modules work in redundancy mode to provide power for the chassis and in load balancing mode to provide power for PDs.
Figure 4-76 shows the power supply mode of dual AC PoE power modules (PWR1 and PWR2). After AC power is transmitted to the PWR modules, the PWR modules provide 12 V and -53 V outputs. The outputs are combined on the motherboard, which then provides 12 V voltage for the switch and -53 V voltage for the PDs.
Figure 4-76 Power supply by dual AC PoE power modules

L: live wire

N: neutral wire

PGND: protection ground

GND: 12 V reference ground

RTN: -53 V reference ground

Heat Dissipation

The S5710-52C-PWR-LI uses pluggable fan modules for forced air cooling. Air flows in from the left and right sides, and exhausts from the rear panel.

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-199 lists technical specifications of the S5710-52C-PWR-LI.

Table 4-199 Technical specifications



Memory (RAM)

256 MB


32 MB

Mean time between failures (MTBF)

50.4 years when a 2-port 10GE interface card is configured, 68.6 years when a 4-port GE front card is configured, 35.58 years when a 4-port 10GE front card is configured

Mean time to repair (MTTR)

2 hours


> 0.99999

Service port surge protection

Common mode: ±1 kV

Power supply surge protection

±2 kV in differential mode, ±4 kV in common mode

Dimensions (H x W x D)

43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.)


  • Empty: ≤ 5 kg (11.02 lb)
  • Fully configured: ≤ 8.5 kg (18.74 lb)

Stack ports

Two stack ports available on each stack card


Not supported



Rated voltage range

100 V AC to 240 V AC, 50/60 Hz

Maximum voltage range

90 V AC to 264 V AC, 47 Hz to 63 Hz

Maximum power consumption (100% throughput, 100% PoE loads, full speed of fans)

917 W (system power consumption: 177 W, PoE: 740 W)

Operating temperature

0°C to 50°C (32°F to 122°F)

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 45 dB(A)

Relative humidity

5% to 95%, noncondensing

Operating altitude

0-5000 m (0-16404 ft.)


  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

Updated: 2019-08-19

Document ID: EDOC1000013597

Views: 559229

Downloads: 14299

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Previous Next