S5700 Series Switches Hardware Description (V200)

S5720-50X-EI-46S-AC

Version Mapping

Table 4-923 lists the mapping between the S5720-50X-EI-46S-AC chassis and software versions.

Table 4-923 Version mapping

Series		Model	Software Version
S5720-EI	S5720-X-EI	S5720-50X-EI-46S-AC	V200R007C00 to V200R019C10 versions NOTE: This model does not match V200R007C10.

Appearance and Structure

Figure 4-368 S5720-50X-EI-46S-AC appearance

1	One console port NOTE: It is used with a console cable. The console cable is not delivered with the switch and needs to be separately purchased if needed.	2	One USB port
3	Forty-six 100/1000BASE-X ports Applicable modules: FE optical module GE optical module GE-CWDM optical module GE copper module (works at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s)	4	Four 10GE SFP+ ports Applicable modules and cables: GE optical module GE-CWDM optical module GE-DWDM optical module GE copper module (only 1000 Mbit/s supported) 10GE SFP+ optical module (OSXD22N00 not supported) 10GE-CWDM optical module 10GE-DWDM optical module (applicable in V200R009C00 and later versions) 1 m, 3 m, and 10 m SFP+ high-speed copper cables 5 m SFP+ high-speed copper cable (applicable in V200R009C00 and later versions) 3 m and 10 m AOC cables
5	AC socket NOTE: It is used with an AC power cable.	6	Ground screw NOTE: It is used with a ground cable.
7	Two QSFP+ stack optical ports Applicable modules and cables: QSFP+ optical module (only QSFP-40G-SR4 and QSFP-40G-iSR supported) 1 m, 3 m, and 5 m QSFP+ high-speed copper cables	8	RPS socket NOTE: It is used with an RPS cable, which is not hot swappable.

Port Description

100/1000BASE-X port

A 100/1000BASE-X port can send and receive data at 100 Mbit/s or 1000 Mbit/s. Table 4-924 describes the attributes of a 100/1000BASE-X port.

Table 4-924 Attributes of a 100/1000BASE-X port

Attribute	Description
Connector type	LC/PC
Optical interface attributes	Depend on the optical module used
Standards compliance	IEEE802.3z
Working mode	100/1000 Mbit/s auto-sensing

10GE SFP+ port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-925 describes the attributes of a 10GE SFP+ Ethernet optical port.

Table 4-925 Attributes of a 10GE SFP+ port

Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the optical module used
Standards compliance	IEEE802.3ae
Working mode	GE/10GE auto-sensing

QSFP+ stack optical port

QSFP+ stack optical ports can only be used for stack connection. Table 4-926 describes the attributes of a QSFP+ stack optical port.

Table 4-926 Attributes of a QSFP+ stack optical port

Attribute	Description
Connector type	MPO
Optical port attributes	Depend on the optical module used
Standards compliance	IEEE802.3ae

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-927.

Table 4-927 Attributes of a console port

Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port of the S5720-EI does not support USB 1.1 and can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5720-50X-EI-46S-AC has 46 downlink optical port indicators, whereas the S5720-50X-EI-AC has 46 downlink electrical port indicators. Symbols and meanings of other indicators on the two switch models are the same. For details, see Indicator Description.

Power Supply Configuration

The S5720-50X-EI-46S-AC has a built-in power module and does not support pluggable power modules. It can connect to an RPS1800 power supply for power redundancy.

Figure 4-369 shows the power supply mode of a built-in AC power module. The built-in AC power module (PWR) receives power from an external power source and provides a 12 V output to the chassis.

Figure 4-369 Power supply mode of a built-in AC power module

L: live wire

N: neutral wire

PGND: protection ground wire

GND: 12 V reference ground

Heat Dissipation

The S5720-50X-EI-46S-AC has two built-in fans for forced air cooling. Air flows in from the left side and front panel, and exhausts from the right side.

Click to enlarge

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-928 lists technical specifications of the S5720-50X-EI-46S-AC.

Table 4-928 Technical specifications

Item	Description
Memory (RAM)	2 GB
Flash	512 MB in total. To view the available flash memory size, run the display version command.
Mean time between failures (MTBF)	67.59 years
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Service port surge protection	NA
Power supply surge protection	±6 kV in differential mode, ±6 kV in common mode
Dimensions (H x W x D)	Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 224.9 mm (1.72 in. x 17.4 in. x 8.85 in.) Maximum dimensions (the depth is the distance from ports on the front panel to the parts protruding from the rear panel): 43.6 mm x 442.0 mm x 229.9 mm (1.72 in. x 17.4 in. x 9.05 in.)
Weight (with packaging)	5 kg (11.03 lb)
Stack ports	Two fixed QSFP+ stack ports on the rear card
RTC	Supported
RPS	Supported
PoE	Not supported
Rated voltage range	100 V AC to 240 V AC, 50/60 Hz
Maximum voltage range	90 V AC to 264 V AC, 47 Hz to 63 Hz
Maximum power consumption (100% throughput, full speed of fans)	81.5 W
Typical power consumption (30% of traffic load) Tested according to ATIS standard EEE enabled No PoE power consumption	73.75 W
Operating temperature	0°C to 45°C (32°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Noise under normal temperature (27°C, sound power)	< 51.1 dB(A)
Relative humidity	5% to 95%, noncondensing
Operating altitude	0-5000 m (0-16404 ft.)
Certification	EMC certification Safety certification Manufacturing certification
Part number	02359583

Version Mapping
Appearance and Structure
Port Description
Indicator Description
Power Supply Configuration
Heat Dissipation
Technical Specifications

Translation

Favorite

Download

Update Date：2024-04-09

Document ID：EDOC1000013597

Downloads：49813

Average rating：3.27Points

Digital Signature File

digtal sigature tool