S5732-H24S6Q (02353AJS/02353AJS-001/02353AJS-003/02353AJS-004)

S5700 Series Switches Hardware Description (V200)

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Version Mapping

Table 4-1502 lists the mapping between the S5732-H24S6Q chassis and software versions.

Table 4-1502 Version mapping

Series	Model	Software Version
S5732-H	S5732-H24S6Q	02353AJS: V200R019C00 and later versions 02353AJS-001: V200R020C10 and later versions 02353AJS-003: V200R021C10SPC500 and later versions (If V200R021C00SPC100 is used, install V200R021SPH011 or a later patch.) 02353AJS-004: V200R021C10SPC600 and later versions (If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch.) NOTE: V200R021C01 is not supported. Some models cannot be downgraded due to component upgrade. Therefore, you are advised to run the display system-software information command (supported in V200R021C00 and later versions) to check the software versions supported by the device before performing a downgrade.

Series

Model

Software Version

S5732-H

S5732-H24S6Q

02353AJS: V200R019C00 and later versions

02353AJS-001: V200R020C10 and later versions

02353AJS-003: V200R021C10SPC500 and later versions (If V200R021C00SPC100 is used, install V200R021SPH011 or a later patch.)

02353AJS-004: V200R021C10SPC600 and later versions (If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch.)

NOTE:

V200R021C01 is not supported.

Some models cannot be downgraded due to component upgrade. Therefore, you are advised to run the display system-software information command (supported in V200R021C00 and later versions) to check the software versions supported by the device before performing a downgrade.

Appearance and Structure

Figure 4-579 S5732-H24S6Q appearance

1	Twenty 1000BASE-X ports Applicable modules: GE optical module GE-CWDM optical module GE-DWDM optical module GE copper module (works at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s)	2	Four 10GE SFP+ ports Applicable modules and cables: GE optical module GE-CWDM optical module GE-DWDM optical module GE copper module (100M/1000M auto-sensing) 10GE SFP+ optical module (OSXD22N00 not supported) 10GE-CWDM optical module 10GE-DWDM optical module 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables 3 m and 10 m SFP+ AOC cables
3	Six 40GE/100GE QSFP+ optical ports Applicable modules and cables: QSFP+ optical module 1 m, 3 m, and 5 m QSFP+ to QSFP+ high-speed copper cables 10 m QSFP+ to QSFP+ AOC cable QSFP28 optical module (supported in V200R020C00 and later versions, with a license loaded) 1 m QSFP28 to QSFP28 high-speed copper cable (supported in V200R020C00 and later versions, with a license loaded) 10 m QSFP28 to QSFP28 AOC cable (supported in V200R020C00 and later versions, with a license loaded) 2 m QSFP28 dedicated stack cable (supported in V200R020C10 and later versions) NOTE: A QSFP+ optical port cannot be split into four 10GE ports, regardless of whether the port uses a QSFP28 or QSFP+ optical module. By default, a QSFP+ optical port is a 40GE port. In V200R020C00 and later versions, a license can be loaded to increase the port rate to 100 Gbit/s. After the license is activated, run the assign port-type 100GE command and restart the switch to configure the port as a 100GE port.	4	Ground screw NOTE: It is used with a ground cable.
5	SSD card slot NOTE: This slot is reserved for future use.	6	One console port
7	One ETH management port	8	One USB port
9	One PNP button NOTICE: To restore the factory settings and reset the switch, hold down the button for at least 6 seconds. To reset the switch, press the button. Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.	10	Fan module slot 1 NOTE: Applicable fan module: FAN-031A-B (Fan box(B,FAN panel side exhaust))
11	Fan module slot 2 NOTE: Applicable fan module: FAN-031A-B (Fan box(B,FAN panel side exhaust))	12	Fan module slot 3 NOTE: Applicable fan module: FAN-031A-B (Fan box(B,FAN panel side exhaust))
13	Fan module slot 4 NOTE: Applicable fan module: FAN-031A-B (Fan box(B,FAN panel side exhaust))	14	Power module slot 1 NOTE: Applicable power module: PAC600S12-CB (600 W AC&240 V DC Power Module) PAC600S12-EB (600 W AC&240 V DC Power Module) PAC600S12-DB (600 W AC&240 V DC Power Module) (applicable in V200R020C10 and later versions) PDC1000S12-DB (1000 W DC Power Module)
15	Power module slot 2 NOTE: Applicable power module: PAC600S12-CB (600 W AC&240 V DC Power Module) PAC600S12-EB (600 W AC&240 V DC Power Module) PAC600S12-DB (600 W AC&240 V DC Power Module) (applicable in V200R020C10 and later versions) PDC1000S12-DB (1000 W DC Power Module)	-	-

Port Description

1000BASE-X Ethernet Optical Port

When a 1000BASE-X port uses a GE optical module, it can only transmit and receive data at 1000 Mbit/s and does not support the 100 Mbit/s transmission speed. When a 1000BASE-X port uses a GE copper module, it can transmit and receive data at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s. Table 4-1503 describes the attributes of a 1000BASE-X Ethernet optical port.

Table 4-1503 Attributes of a 1000BASE-X Ethernet optical port

Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the module used
Standards compliance	IEEE802.3z

10GE SFP+ optical port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-1504 describes the attributes of a 10GE SFP+ Ethernet optical port.

Table 4-1504 Attributes of a 10GE SFP+ port

Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the optical module used
Standards compliance	IEEE802.3ae
Working mode	GE/10GE auto-sensing

40GE QSFP+ optical port

A 40GE QSFP+ optical port sends and receives service traffic at 40 Gbit/s. Table 4-1505 describes the attributes of a QSFP+ optical port.

Table 4-1505 Attributes of a QSFP+ optical port

Attribute	Description
Connector type	MPO/LC
Optical port attributes	Depend on the optical module used
Standards compliance	IEEE802.3ba

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-1506.

Table 4-1506 Attributes of a console port

Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port. Table 4-1507 describes the attributes of an ETH management port.

Table 4-1507 Attributes of an ETH management port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3
Working Mode	10/100 Mbit/s auto-sensing
Maximum transmission distance	100 m

In V200R012C00 and later versions, you can log in to the switch that contains the ETH management port for the first time through the ETH port. For details, see "First Login to a Switch" in the Configuration Guide - Basic Configuration. If you have logged in to the switch for the first time by pressing and holding the MODE button for 6 seconds or longer and saved the configuration, the default configuration on the ETH port will be cleared. In this case, you cannot log in to the switch for the first time through the ETH port. You are advised to log in to the switch for the first time through the ETH port.

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

Figure 4-580 Indicators on the S5732-H24S6Q

Table 4-1508 Description of indicators on the switch

No.	Indicator	Name	Color	Status	Description
1	SYS	System status indicator	-	Off	The system is not running.
			Green	Fast blinking	The system is starting.
			Green	Steady on	During the system startup preparation phase, the SYS indicator is steady green, which lasts for a maximum of 30 seconds.
			Green	Slow blinking	The system is running normally.
			Red	Steady on	The system does not work normally after registration, or a fan alarm or a temperature alarm has been generated.
2	MST	Stack indicator	-	Off	The switch is not the master switch in a stack.
2	MST	Stack indicator	Green	Blinking	The switch is the master switch in a stack or a standalone switch.
3	ID	ID indicator	-	Off	The ID indicator is not used (default state).
3	ID	ID indicator	Blue	Steady on	The indicator identifies the switch to maintain. The ID indicator can be turned on or off remotely to help field engineers find the switch to maintain.
4	-	Service port indicator (GE/10GE optical port)	-	Off	The port is not connected or has been shut down.
			Green	Steady on	A link has been established on the port.
			-	Off	The port is not sending or receiving data.
			Yellow	Blinking	The port is sending or receiving data.
5	-	Service port indicator (40GE/100GE optical port)	-	Off	The port is not connected or has been shut down.
			Green	Steady on	A link has been established on the port.
			Green	Blinking	The port is sending or receiving data.
6	L/A	ETH port indicator	-	Off	The ETH port is not connected.
			Green	Steady on	The ETH port is connected.
			Green	Blinking	The Eth port is sending or receiving data.
7	USB	USB-based deployment indicator	-	Off	No USB flash drive is connected to the switch. The USB port is damaged. The indicator is damaged. The USB flash drive does not have any configuration file and cannot be used for deployment. The switch has been upgraded using the USB flash drive and is restarting.
			Green	Steady on	A USB-based deployment has been completed.
			Green	Blinking	The system is reading data from a USB flash drive.
			Yellow	Steady on	The switch has copied all the required files and completed the file check. The USB flash drive can be removed from the switch.
			Red	Blinking	An error has occurred when the system is executing the configuration file or reading data from the USB flash drive.

Power Supply Configuration

The switch can use a single power module or double power modules for 1+1 power redundancy. Pluggable AC and DC power modules can be used together in the same switch.

Heat Dissipation

The S5732-H24S6Q uses pluggable fan modules for forced air cooling. Air flows in from the front side and exhausts from the rear panel.

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-1509 lists technical specifications of the S5732-H24S6Q.

Table 4-1509 Technical specifications

Item	Description
Memory (RAM)	4 GB
Flash	2 GB in total. To view the available flash memory size, run the display version command.
Mean time between failures (MTBF)	62.27 years
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Service port surge protection	N/A
Power supply surge protection	Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode Using DC power modules: ±2 kV in differential mode, ±4 kV in common mode
Dimensions (H x W x D)	Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.) Maximum dimensions (the depth is the distance from ports on the front panel to the handle on the rear panel): 43.6 mm x 442.0 mm x 446.0 mm (1.72 in. x 17.4 in. x 17.6 in.)
Weight (with packaging)	8.9 kg (19.62 lb)
Stack ports	Any QSFP+ ports
RTC	Supported
RPS	Not supported
PoE	Not supported
Rated voltage range	AC input: 100 V AC to 240 V AC, 50/60 Hz High-Voltage DC input: 240 V DC DC input: -48 V DC to -60 V DC
Maximum voltage range	AC input: 90 V AC to 290 V AC, 45 Hz to 65 Hz High-Voltage DC input: 190 V DC to 290 V DC DC input: -38.4 V DC to -72 V DC
Maximum power consumption (100% throughput, full speed of fans)	229 W
Typical power consumption (30% of traffic load, tested according to ATIS standard)	126 W
Operating temperature	-5°C to +45°C (23°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.). The switch cannot be started when the ambient temperature is lower than 0°C (32°F). The operating temperature of the switch is -5°C to 40°C (23°F to 104°F) when it uses QSFP-100G-ER4 optical module.
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Noise under normal temperature (27°C, sound power)	< 65 dB(A)
Relative humidity	5% to 95%, noncondensing
Operating altitude	0-5000 m (0-16404 ft.)
Certification	EMC certification Safety certification Manufacturing certification
Part number	02353AJS 02353AJS-001 02353AJS-003 02353AJS-004

Indicator Description

Translation

简体中文

Download

Updated: 2023-06-15

Document ID: EDOC1000013597

Downloads: 43562

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate