No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


S5700 Series Switches Hardware Description

This document provides an overall description of the S5700 hardware, helping you obtain detailed information about each chassis, card, power module, fan module, cable, and optical module.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ES5D00G4SA01 (4-Port GE SFP Front Optical Interface Card)

ES5D00G4SA01 (4-Port GE SFP Front Optical Interface Card)

Version Mapping

Table 8-23 lists the mapping between the ES5D00G4SA01 card and software versions.

Table 8-23 Version mapping

Card Model

Software Version
After the display device command is executed, the PCB model of the card is displayed as ES510G4SA.
V100R005C01 to V200R005C02
This module is not supported in V200R001C01, V200R003C02, V200R003C10, or V200R005C01.

Card Overview

The ES5D00G4SA01 provides four GE SFP optical ports for data access and line-rate switching. It can be installed in a front card slot of the switch models listed in Table 8-24.

Table 8-24 Applicable switch models
Card Switch Model
  • S5700-28C-SI
  • S5700-52C-SI
  • S5700-28C-PWR-SI
  • S5700-52C-PWR-SI
  • S5710-28C-LI
  • S5710-52C-LI
  • S5710-28C-PWR-LI
  • S5710-52C-PWR-LI

Figure 8-12 shows the appearance of the ES5D00G4SA01.

Figure 8-12 ES5D00G4SA01


Table 8-25 describes functions of the ES5D00G4SA01.

Table 8-25 Functions



Basic function

Provides four GE SFP optical ports for data access and line-rate switching.

GE port

A GE port is often used as an uplink aggregation port on high-bandwidth and high-speed MANs or backbone networks. When an enterprise needs high-quality triple-play service, use the ES5D00G4SA01 to provide access ports for downlink devices or networks.

Usage Constraints

  • If the ES5D00G4SA01 is installed on the S5700-EI, the front card cannot register.
  • The ES5D00G4SA01 front card can provide four ports only if it is used with an ES5D00ETPB00 extended rear card. If no ES5D00ETPB00 extended rear card is used, only the first two ports on the ES5D00G4SA01 front card are available.
  • When an S5700-SI/S5710-C-LI is equipped with the ES5D00ETPC00 stack rear card, only ports 1 and 2 are available if the ES5D00G4SA01 front card is used.

  • The ES5D00G4SA01 is not hot swappable.

Indicators and Ports

Figure 8-13 shows indicators on the ES5D00G4SA01.

Figure 8-13 Indicators on the ES5D00G4SA01

Table 8-26 describes indicator status on the ES5D00G4SA01.

Table 8-26 Indicator description








  • Steady on: A link is established on the port.
  • Blinking: The port is sending or receiving data.


No link is established on the port.

Figure 8-14 shows the ports on the ES5D00G4SA01.

Figure 8-14 Ports on the ES5D00G4SA01

1. Four GE SFP optical ports

GE SFP optical port

The ES5D00G4SA01 provides four GE optical ports to transmit and receive Ethernet service data at 1000 Mbit/s. Table 8-27 describes attributes of an SFP optical port.

The GE SFP ports support GE optical and copper modules (used with shielded Ethernet cables).

A GE SFP port can go Up after a GE copper module is installed. However, electrical attributes, such as the rate, duplex mode, auto-negotiation, MDI, flow control, and virtual cable test, are not configurable in this case.

Table 8-27 Attributes of an SFP optical port
Attribute Description
Connector type LC/PC
Optical port attributes Depend on the optical module used (see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, GE-DWDM eSFP Optical Modules, and GE SFP Copper Modules)
Standards compliance IEEE 802.3z

Technical Specifications

Table 8-28 lists technical specifications of the ES5D00G4SA01.

Table 8-28 Technical specifications



Physical specifications

  • Dimensions (H x W x D): 22 mm x 70 mm x 197 mm (0.87 in. x 2.8 in. x 7.8 in.)
  • Weight: 0.2 kg (0.44 lb)
  • Maximum power consumption: 4.5 W

Environment specifications

  • Operating temperature: 0°C to 50°C (32°F to 122°F)
  • Relative humidity: 5% to 95%
  • Storage temperature: -40°C to +70°C (-40°F to +158°F)

Ordering Information

Ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 8-29 provides the ES5D00G4SA01 ordering information.

Table 8-29 Ordering information

Card Description

Card Name

Part Number
4-port GE SFP optical interface card (consisting of an ES5D00G4SA01 4-port GE front card and an ES5D00ETPB00 extended channel rear card)

This card is applicable to the SI series.

The ES5D00G4SA01 front card must work with the ES5D00ETPB00 rear card, so the two cards are sold together. ES5D00G4SA00 is the name of the combination of the two cards.
Updated: 2019-08-19

Document ID: EDOC1000013597

Views: 557335

Downloads: 14261

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Previous Next