ES5D000G4S01 (4-Port GE SFP Front Optical Interface Card)
Version Mapping
Table 8-16 lists the mapping between the ES5D000G4S01 card and software versions.
Card Overview
The ES5D000G4S01 provides four GE SFP optical ports for data access and line-rate switching. It can be installed in a front card slot of the switch models listed in Table 8-17.
Card |
Switch Model |
|---|---|
ES5D000G4S01 |
|
Figure 8-9 shows the appearance of the ES5D000G4S01.
Functions
Table 8-18 describes functions of the ES5D000G4S01.
Function |
Description |
|---|---|
Basic function |
Provides four GE SFP optical ports for data access and line-rate switching. |
GE port |
A GE port is often used as an uplink aggregation port on high-bandwidth and high-speed MANs or backbone networks. When an enterprise needs high-quality triple-play service, use the ES5D000G4S01 to provide access ports for downlink devices or networks. |
Usage Constraints
- If the ES5D000G4S01 is installed on the S5700-SI or S5710-C-LI, the front card cannot register.
- The ES5D000G4S01 front card can provide four ports only if it is used with an ES5D00ETPB00 extended rear card. If no ES5D00ETPB00 extended rear card is used, only the first two ports on the ES5D000G4S01 front card are available.
When an S5700-EI is equipped with the ES5D00ETPC00 stack rear card, only ports 1 and 2 are available if the ES5D000G4S01 front card is used.
- The ES5D000G4S01 is not hot swappable.
Indicators and Ports
Figure 8-10 shows indicators on the ES5D000G4S01.
Table 8-19 describes indicator status on the ES5D000G4S01.
Number |
Indicator |
Color |
Description |
|---|---|---|---|
1 |
ACT/LINK |
Green |
|
Off |
No link is established on the port. |
Figure 8-11 shows the ports on the ES5D000G4S01.
1. Four GE SFP optical ports |
GE SFP port
The ES5D000G4S01 provides four GE optical ports to transmit and receive Ethernet service data at 1000 Mbit/s. Table 8-20 describes attributes of an SFP optical port.
The GE SFP ports support GE optical and copper modules (used with shielded Ethernet cables).
A GE SFP port can go Up after a GE copper module is installed. However, electrical attributes, such as the rate, duplex mode, auto-negotiation, MDI, flow control, and virtual cable test, are not configurable in this case.
Attribute |
Description |
|---|---|
Connector type |
LC/PC |
Optical port attributes |
Depend on the optical module used (see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, GE-DWDM eSFP Optical Modules, and GE SFP Copper Modules) |
Standards compliance |
IEEE 802.3z |
Technical Specifications
Table 8-21 lists technical specifications of the ES5D000G4S01.
Ordering Information
Ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.
Table 8-22 provides the ES5D000G4S01 ordering information.
Card Description |
Card Name |
Part Number |
|---|---|---|
4-port GE SFP optical interface card (consisting of an ES5D000G4S01 4-port GE front card and an ES5D00ETPB00 extended channel rear card) This card is applicable to the EI series. |
ES5D000G4S00 NOTE:
The ES5D000G4S01 front card must work with the ES5D00ETPB00 rear card, so the two cards are sold together. ES5D000G4S00 is the name of the combination of the two cards. |
02319957 |