No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S5700 Series Switches Hardware Description

This document provides an overall description of the S5700 hardware, helping you obtain detailed information about each chassis, card, power module, fan module, cable, and optical module.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
S5700-52C-EI

S5700-52C-EI

Version Mapping

Table 4-727 lists the mapping between the S5700-52C-EI and software versions.

Table 4-727 Version mapping

Series

Model

Software Version
S5700-EI S5700-52C-EI

V100R005C01 to V200R005C03

NOTE:
This model does not match V200R003C02 or V200R003C10.

Appearance and Structure

Figure 4-289 S5700-52C-EI appearance
1 Forty-eight 10/100/1000BASE-T ports 2 One console port
3 One ETH management port 4 Front card slot
5 ESD jack
NOTE:

Before installing or maintaining a switch, wear an ESD wrist strap and insert the other end of the ESD wrist strap into this ESD jack.

6 Rear card slot
7 Fan slot
NOTE:

Applicable fan module:

CX7E1FANA fan module

8 Power module slot 2
NOTE:
Applicable power modules:
9 Power module slot 1
NOTE:
Applicable power modules:
- -

Port Description

10/100/1000BASE-T port
A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-728 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-728 Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3, IEEE802.3u, IEEE802.3ab

Working mode

10/100/1000 Mbit/s auto-sensing

Maximum transmission distance

100 m

Console port
The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-729.
Table 4-729 Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

ETH management port
You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For details on how to use the ETH management port, see the Configuration Guide - Basic Configurations. Table 4-730 describes the attributes of an ETH management port.
Table 4-730 Attributes of an ETH management port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3

Working mode

10/100 Mbit/s auto-sensing

Maximum transmission distance

100 m

Indicator Description

The S5700-52C-EI has the same types of indicators as the S5700-28C-EI. For details, see Indicator Description.

Power Supply Configuration

The S5700-52C-EI can use a single power module or double power modules for 1+1 power redundancy. In versions prior to V200R005C00, the switch cannot use pluggable AC and DC power modules simultaneously. In V200R005C00 and later versions, the switch supports mixing of pluggable AC and DC power modules.

Figure 4-290 shows the power supply connections of dual DC power modules. After DC power is transmitted to the PWR module, the PWR module provides 12 V output voltage, and the motherboard provides power for the entire device.
Figure 4-290 Power supply connections of dual DC power modules

NEG: negative cable

RTN: positive cable

GND: 12 V reference ground

Figure 4-291 shows the power supply connections of dual non-PoE AC power modules. After AC power is transmitted to the PWR module, the PWR module provides 12 V output voltage, and the motherboard provides power for the entire device.
Figure 4-291 Power supply connections of dual non-PoE AC power modules

L: Live wire

N: Neutral wire

PGND: Protection ground cable

GND: 12 V reference ground

Heat Dissipation

The S5700-52C-EI uses pluggable fan modules for forced air cooling. Air flows in from the left and right sides, and exhausts from the rear panel.

NOTE:
This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-731 lists technical specifications of the S5700-52C-EI.

Table 4-731 Technical specifications

Item

Description

Memory (RAM)

256 MB

Flash

32 MB

Mean time between failures (MTBF)

46.05 years when a 2-port 10GE interface card is configured, 57.08 years when a 4-port GE front card is configured, 25.58 years when a 4x10GE front card is configured

Mean time to repair (MTTR)

2 years

Availability

> 0.99999

Service port surge protection

Common mode: ±2 kV

Power supply surge protection

  • Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode
  • Using DC power modules: ±1 kV in differential mode, ±2 kV in common mode

Dimensions (H x W x D)

43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.)

Weight

  • Empty: ≤ 5 kg (11.02 lb)
  • Fully configured: ≤ 8.5 kg (18.74 lb)

Stack ports

Two stack ports available on each stack card

RPS

Not supported

PoE

Not supported

Rated voltage range

100 V AC to 240 V AC, 50/60 Hz

-48 V DC to -60 V DC

Maximum voltage range

90 V AC to 264 V AC, 47 Hz to 63 Hz

-36 V DC to -72 V DC

Maximum power consumption (100% throughput, full speed of fans)

88 W

Operating temperature

0°C to 50°C (32°F to 122°F)

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 41 dB(A)

Relative humidity

5% to 95%, noncondensing

Operating altitude

  • AC power modules configured: 0-5000 m (0-16404 ft.)
  • DC power modules configured: 0-2000 m (0-6562 ft.)

Certification

  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

02352354
Translation
Download
Updated: 2019-08-19

Document ID: EDOC1000013597

Views: 597403

Downloads: 14825

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next