No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S5700 Series Switches Hardware Description

This document provides an overall description of the S5700 hardware, helping you obtain detailed information about each chassis, card, power module, fan module, cable, and optical module.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
S5710-52C-EI

S5710-52C-EI

Version Mapping

Table 4-755 lists the mapping between the S5710-52C-EI chassis and software versions.

Table 4-755  Version mapping

Series

Model

Software Version
S5710-EI S5710-52C-EI

V200R001C00 to V200R005C02

NOTE:
This model does not match V200R001C01, V200R003C02, V200R003C10, or V200R005C01.

Appearance and Structure

Figure 4-301  S5710-52C-EI appearance
1 Forty-eight 10/100/1000BASE-T ports 2 Four 10GE SFP+ ports
3 One ETH management port 4 One mini USB port
5 One console port 6 One USB port
7 Ground screw
NOTE:
It is used with a ground cable.
8 Rear card slot 1
9 Rear card slot 2 10 ESN label
NOTE:

You can draw it out to view the ESN and MAC address of the switch.

11 Power module slot 2
NOTE:
Applicable power modules:
12 Power module slot 1
NOTE:
Applicable power modules:

Port Description

10/100/1000BASE-T port
A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-756 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-756  Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3, IEEE802.3u, IEEE802.3ab

Working mode

10/100/1000 Mbit/s auto-sensing

Maximum transmission distance

100 m

10GE SFP+ port
A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-757 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 4-757  Attributes of a 10GE SFP+ port

Attribute

Description

Connector type

LC/PC

Optical port attributes

Depend on the optical module used

Standards compliance

IEEE802.3ae

Working mode

GE/10GE auto-sensing

Console port
The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-758.
Table 4-758  Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

Mini USB port

The mini USB port is connected to a console for on-site configuration. When both the Mini USB and console port have a cable connected, only the Mini USB port works.

ETH management port
You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For details on how to use the ETH management port, see the Configuration Guide - Basic Configurations. Table 4-759 describes the attributes of an ETH management port.
Table 4-759  Attributes of an ETH management port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3

Working mode

10/100 Mbit/s auto-sensing

Maximum transmission distance

100 m

USB port
The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.
NOTE:
USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5710-52C-EI has the same types of indicators as the S5710-28C-EI. For details, see Indicator Description.

Power Supply Configuration

The S5710-52C-EI uses pluggable power modules. It can be configured with a single power module or double power modules for 1+1 power redundancy. Pluggable AC and DC power modules can be used together in the same switch.

Figure 4-302 shows the power supply connections of dual DC power modules. After DC power is transmitted to the PWR module, the PWR module provides 12 V output voltage, and the motherboard provides power for the entire device.
Figure 4-302  Power supply connections of dual DC power modules

NEG: negative cable

RTN: positive cable

GND: 12 V reference ground

Figure 4-303 shows the power supply connections of dual non-PoE AC power modules. After AC power is transmitted to the PWR module, the PWR module provides 12 V output voltage, and the motherboard provides power for the entire device.
Figure 4-303  Power supply connections of dual non-PoE AC power modules

L: Live wire

N: Neutral wire

PGND: Protection ground cable

GND: 12 V reference ground

Heat Dissipation

The S5710-52C-EI has five built-in fans for forced air cooling. The airflow direction is left-to-right.

NOTE:
This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-760 lists technical specifications of the S5710-52C-EI.

Table 4-760  Technical specifications

Item

Description

Memory (RAM)

512 MB

Flash

  • V200R001: 64 MB
  • V200R002 and later versions: 200 MB

Mean time between failures (MTBF)

45.57 years when an 8-port GE optical card is configured, 44.85 years when an 8-port GE electrical card is configured, 43.33 years when a 2-port 10GE interface card is configured

Mean time to repair (MTTR)

2 hours

Availability

> 0.99999

Service port surge protection

Common mode: ±2 kV

Power supply surge protection

  • Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode
  • Using DC power modules: ±1 kV in differential mode, ±2 kV in common mode

Dimensions (W x D x H)

442.0 mm x 420.0 mm x 44.4 mm (17.4 in. x 16.5 in. x 1.75 in.)

Weight

  • Empty: ≤ 6 kg (13.23 lb)
  • Fully loaded: ≤ 10 kg (22.05 lb)

Stack ports

Four fixed 10GE SFP+ ports on the front panel or ports on the 2-port 10GE rear card

RPS

Not supported

PoE

Not supported

Rated voltage range

100 V AC to 240 V AC, 50/60 Hz

-48 V DC to -60 V DC

Maximum voltage range

90 V AC to 264 V AC, 47 Hz to 63 Hz

-36 V DC to -72 V DC

Maximum power consumption (100% throughput, full speed of fans)

146.9 W

Operating temperature

0°C to 50°C (32°F to 122°F) at an altitude of 0-1800 m (0-5906 ft.)

NOTE:

When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 53.9 dB(A)

Relative humidity

5% to 95%, noncondensing

Operating altitude

  • AC power modules configured: 0-5000 m (0-16404 ft.)
  • DC power modules configured: 0-2000 m (0-6562 ft.)

Certification

  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

02353169
Translation
Download
Updated: 2019-05-16

Document ID: EDOC1000013597

Views: 371331

Downloads: 12060

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next