No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade
S6700 Series Switches Hardware Description

This document provides an overall description of the S6700 hardware, helping you obtain detailed information about each chassis, power module, fan module, cable, and optical module.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
S6700-48-EI

S6700-48-EI

Version Mapping

Table 5-11 lists the mapping between the S6700-48-EI and software versions.

Table 5-11 Version mapping

Series

Model

Software Version

S6700-EI

S6700-48-EI

V100R006C00 to V200R005C02

Appearance and Structure

Figure 5-7 S6700-48-EI appearance

1

Forty-eight 10GE SFP+ ports

2

One ETH management port

3

One console port

4

One USB port

5

Ground screw

NOTE:
It is used with a ground cable.

6

ESD jack

NOTE:

Before installing or maintaining a switch, wear an ESD wrist strap and insert the other end of the ESD wrist strap into this ESD jack.

7

Fan slot 2

NOTE:

Applicable fan module:

CX7E1FANA fan module

8

Fan slot 1

NOTE:

Applicable fan module:

CX7E1FANA fan module

9

Power module slot 2

10

Power module slot 1

Port Description

10GE SFP+ port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 5-12 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 5-12 Attributes of a 10GE SFP+ port

Attribute

Description

Connector type

LC/PC

Optical port attributes

Depend on the optical module used

Standards compliance

IEEE802.3ae

Working mode

GE/10GE auto-sensing

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 5-13.
Table 5-13 Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For details on how to use the ETH management port, see the Configuration Guide - Basic Configurations. Table 5-14 describes the attributes of an ETH management port.
Table 5-14 Attributes of an ETH management port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3

Working mode

10/100 Mbit/s auto-sensing

Maximum transmission distance

100 m

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S6700-48-EI has the same types of indicators as the S6700-24-EI. For details, see Indicator Description.

Power Supply Configuration

The S6700-48-EI can use a single power module or double power modules for 1+1 power redundancy. In versions prior to V200R005C00, the switch cannot use AC and DC power modules simultaneously. In V200R005C00 and later versions, the switch support mixing of AC and DC power modules.

Figure 5-8 shows the power supply connections of dual DC power modules. After DC power is transmitted to the PWR module, the PWR module provides -53 V output voltage, and the motherboard provides power for the entire device.
Figure 5-8 Power supply connections of dual DC power modules

NEG: Negative wire

RTN: Positive wire

GND: -53 V reference ground

Figure 5-9 shows the power supply connections of dual AC power modules. After AC power is transmitted to the PWR module, the PWR module provides -53 V output voltage, and the motherboard provides power for the entire device.
Figure 5-9 Power supply connections of dual AC power modules

L: Live wire

N: Neutral wire

PGND: Protection ground wire

GND: -53 V reference ground

Heat Dissipation

The S6700-48-EI uses pluggable fan modules for forced air cooling. Air flows in from the left and right sides, and exhausts from the rear panel.

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 5-15 lists technical specifications of the S6700-48-EI.

Table 5-15 Technical specifications

Item

Description

Memory (RAM)

512 MB

Flash

64 MB

Mean time between failures (MTBF)

33.76

Mean time to repair (MTTR)

2 hours

Availability

> 0.99999

Service port surge protection

NA

Power supply surge protection

  • Using AC power modules: ±2 kV in differential mode, ±4 kV in common mode
  • Using DC power modules: ±1 kV in differential mode, ±2 kV in common mode

Dimensions (H x W x D)

43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.)

Weight

  • Empty: ≤ 5 kg (11.02 lb)
  • Fully configured: ≤ 8.5 kg (18.74 lb)

Stack ports

Any 10GE SFP+ ports (a maximum of eight physical ports)

RPS

Not supported

PoE

Not supported

Rated voltage range

100 V AC to 240 V AC, 50/60 Hz

-48 V DC to -60 V DC

Maximum voltage range

90 V AC to 264 V AC, 47 Hz to 63 Hz

-38.4 V DC to -72 V DC

Maximum power consumption (100% throughput, full speed of fans)

240 W

Operating temperature

-5°C to +50°C (23°F to 122°F) at an altitude of 0-1800 m (0-5906 ft.)

NOTE:
  • The operating temperature of the switch is -5°C to +45°C (23°F to 113°F) when it uses SFP+ optical modules with 40 km or longer transmission distances.
  • When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 55 dB(A)

Relative humidity

5% to 95%, noncondensing

Operating altitude

0-5000 m (0-16404 ft.)

Certification

  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

02352767

Translation
Download
Updated: 2020-02-17

Document ID: EDOC1000013621

Views: 225299

Downloads: 4051

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next