No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CX910 Switch Module V100R001C00 User Guide 22

This document describes the CX910 10GE switch module (CX910 for short) of the Tecal E9000 server in terms of its features, installation, removal, and configuration. This document applies to the CX910 whose GE/10GE switching planes use the software versions of 1.1.x.x.x, and 1.23-1.99.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Logging In to a Server Over a Serial Port by Using PuTTY

Logging In to a Server Over a Serial Port by Using PuTTY

Scenarios

Log in to a server over a serial port by using PuTTY in the following scenarios:

  • The server is configured for the first time at a new site, and you need to perform initial configuration.
  • The server cannot be remotely connected to because the network is faulty, and you need to locate the fault.
    NOTE:

    The server that is logged in to is a management module, compute node, or switch module in an E9000 chassis.

    When logging in to a management module, you must connect the serial port to the COM serial port of the MM910.

    When logging in to a compute node, you can connect the serial port to the SYS serial port or BMC chip of the compute node.
    • The E9000 compute nodes do not provide serial ports. To log in to a compute node over a serial port, connect a multi-port cable to a universal connector port (UCP) and log in through the serial port of the multi-port cable. If the compute node does not provide a UCP, you can log in to the compute node only through a network port. For details, see Logging In to a Compute Node or a Switch Module over SOL.
    • On the MM910 CLI, run the bmccomstate and switchcom commands to query and switch the objects connected to the serial ports. For details, see the MM910 Management Module V100R001 Command Reference.

    When logging in to a switch module, you can connect the serial port to the Ethernet switching plane, FC switching plane, or BMC chip.

    • If the switch module panel has the BMC serial port and SYS serial port, the BMC serial port is connected to the BMC chip, and the SYS serial port can be connected to the Ethernet switching plane or FC switching plane.
    • If the switch module panel has only the COM serial port, the COM serial port can be connected to the Ethernet switching plane, FC switching plane, or BMC chip.
    • If the switch module panel has only the BMC serial port, the BMC serial port is connected to the BMC chip.
    • On the MM910 CLI, run the bmccomstate and switchcom commands to query and switch the objects connected to the serial ports. For details, see the MM910 Management Module V100R001 Command Reference.

Prerequisites

Software

PuTTY 0.60 or later.

Procedure

  1. Connect the local PC and the target device through a serial cable.

    The connection varies depending on the target device:

    • Compute node: Connect the local PC to the serial port of the multi-port cable of the target compute node.
    • Switch module: Connect the local PC to the serial port of the target switch module.
    • Management module: Connect the local PC to the serial (COM) port of the target MM910.

  2. Double-click PuTTY.exe.

    The PuTTY Configuration window is displayed.

  3. In the navigation tree on the left, choose Connection > Serial.
  4. Set the login parameters.

    The following are the examples:

    • Serial line to connect to: COMn
    • Speed (baud): 115200
    • Data bits: 8
    • Stop bits: 1
    • Parity: None
    • Flow control: None
    NOTE:

    n indicates the serial port number, and the value is an integer.

  5. In the navigation tree, choose Session.
  6. Select Connection type in Serial.

    Figure 6-3 PuTTY Configuration window

  7. Click Open.

    The PuTTY window and login as: are displayed, waiting for you to enter a user name.

  8. Enter a user name and password by following instructions.

    After login, the server host name is displayed on the left of the prompt.

Translation
Download
Updated: 2018-09-20

Document ID: EDOC1000015891

Views: 14254

Downloads: 335

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next