About This Document
Purpose
This document describes FusionServer Pro E9000 server alarms of all hardware devices in the chassis in terms of the meaning, impact on the system, possible causes, and solutions.
Table 1 shows the components involved in alarms.
Type |
Name |
---|---|
Management module |
MM910 |
Fan module |
Fan |
PSU |
PSU |
Compute node |
|
Switch module |
CX110, CX111, CX116, CX210, CX220, CX310, CX311, CX312, CX317, CX318, CX320, CX610, CX611, CX620, CX621, CX710, CX820, CX910, CX912, CX913, CX915, CX916, CX916L, CX920, CX930. |
Intended Audience
This document is intended for:
- Technical support personnel
- Maintenance engineers
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol |
Description |
---|---|
Indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. |
|
Indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. |
|
Indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. |
|
Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results. NOTICE is used to address practices not related to personal injury. |
|
Supplements the important information in the main text. NOTE is used to address information not related to personal injury, equipment damage, and environment deterioration. |
Change History
Issue |
Date |
Description |
---|---|---|
26 |
2021-08-30 |
Updated 0x0D02FFFF. |
25 |
2020-12-31 |
Updated STACKMNG_1.3.6.1.4.1.2011.5.25.183.1.22.55 hwStackLinkTopoSinglePortAlarm. |
24 |
2020-06-22 |
Modified the hyperlinks in Using the Alarm Query Tool and Technical Support. |
23 |
2020-04-13 |
Modified the alarm handling procedure in 0x1B01FFFF. Modified the alarm handling procedures in 0x014BFF02 and 0x1D00002B. |
22 |
2019-11-11 |
Modified the alarm handling procedure in 0x0541FF28. |
21 |
2019-07-30 |
Changed the document name. |
20 |
2019-07-01 |
Modified the 0D02FFFF alarm. |
19 |
2018-08-10 |
Adjusted the document format. |
18 |
2018-05-28 |
Modified the 120004FF alarm. |
17 |
2018-03-30 |
Modified the hwStorageUtilizationRisingAlarm alarm. |
16 |
2018-01-30 |
Updated sensor information. |
Added the optical module alarm. |
||
15 |
2017-09-15 |
Added CX320 Switch Module Alarms and CX920 Switch Module Alarms. |
Modified ALM-0741FF28 Transition to Non-critical From OK. |
||
14 |
2017-03-30 |
Added ALM-1B01FFFF Major Alarm Caused by Config Error. |
13 |
2016-12-05 |
Added ALM-1B01FFFF Easylink Config Error. |
12 |
2016-10-28 |
Updated CX11x, CX31x, CX710, and CX91x Switch Module Alarms (Software Version 1.2.1.0.39 or Later). |
11 |
2015-05-08 |
Modified ALM-0149FF01 Major Alarm Caused by Overtemperature. |
10 |
2015-02-16 |
Modified ALM-2100FFFF Power Supply Failure (Power Status). |
09 |
2014-11-10 |
Modified the following:
|
08 |
2014-09-15 |
Deleted "Tecal". |
07 |
2014-07-30 |
Added CX11x, CX31x, CX710, and CX91x Switch Module Alarms (Software Version 1.2.1.0.39 or Later). |
06 |
2014-02-15 |
Modified the "Possible Causes" section in ALM-1B01FFFF Major Alarm Caused by Config Error. |
05 |
2014-01-01 |
Added ALM-2C01FFFF FRU Inactive. |
04 |
2013-11-18 |
Modified the "Possible Causes" section in ALM-1B01FFFF Major Alarm Caused by Config Error. |
03 |
2013-06-01 |
New sensors are added to:
|
02 |
2013-04-01 |
Added the following:
|
|
||
Delete Alarm Syntax, and divided the original content into MM910 Alarm Syntax and Switch Module Alarm Syntax. |
||
01 |
2013-01-04 |
This issue is the first official release. |