No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

E9000 Server V100R001 HMM Alarm Handling 19

This document describes E9000 server alarms in terms of the meaning, impact on the system, possible causes, and solutions.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
DEVM

DEVM

DEVM_1.3.6.1.4.1.2011.5.25.41.4.1 hwIfMonitorCrcErrorRising

Description

The CRC error is rising. (hwIfMonitorIndex=[EntityPhysicalIndex], hwIfMonitorCrcErrorStatistics=[hwIfMonitorCrcErrorStatistics], hwIfMonitorCrcErrorThreshold=[hwIfMonitorCrcErrorThreshold], hwIfMonitorCrcErrorInterval=[hwIfMonitorCrcErrorInterval])

The number of CRC error packets that an interface received in a specified period exceeded the upper threshold.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.41.4.1

Trap severity

Critical

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.41.4.2 hwIfMonitorCrcErrorResume

Parameters

Name

Meaning

hwIfMonitorIndex

Indicates the index of the entity.

hwIfMonitorCrcErrorStatistics

Indicates real-time statistics on CEC error packets.

hwIfMonitorCrcErrorThreshold

Indicates the upper threshold for CRC error packets.

hwIfMonitorCrcErrorInterval

Indicates the interval for collecting statistics.

Impact on the System

The interface becomes Down if it receives too many CRC error packets.

Possible Causes

The number of CRC error packets that an interface received in a specified period exceeded the upper threshold.

Procedure
  1. Run the display this command in the interface view to check whether the alarm threshold is set too small. Users can specify the threshold range according to service requirements.
  • If so, go to Step 2.
  • If not, go to Step 3.
  1. Run the trap-threshold error-statistics command in the interface view to set the alarm threshold to a larger value. Check whether the fault is rectified.

    • If so, no action is required.
    • If not, go to Step 3.

  2. Collect trap messages, log messages, and configurations, and contact Huawei technical support personnel.

DEVM_1.3.6.1.4.1.2011.5.25.41.4.2 hwIfMonitorCrcErrorResume

Description

The CRC error alarm resume. (hwIfMonitorIndex=[EntityPhysicalIndex], hwIfMonitorCrcErrorStatistics=[hwIfMonitorCrcErrorStatistics], hwIfMonitorCrcErrorThreshold=[hwIfMonitorCrcErrorThreshold], hwIfMonitorCrcErrorInterval=[hwIfMonitorCrcErrorInterval])

The number of CRC error packets that an interface received in a specified period fell below the upper threshold.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.41.4.2

Trap severity

Critical

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.41.4.1 hwIfMonitorCrcErrorRising

Parameters

Name

Meaning

hwIfMonitorIndex

Indicates the index of the entity.

hwIfMonitorCrcErrorStatistics

Indicates real-time statistics on CEC error packets.

hwIfMonitorCrcErrorThreshold

Indicates the upper threshold for CRC error packets.

hwIfMonitorCrcErrorInterval

Indicates the interval for collecting statistics.

Impact on the System

The number of CRC error packets received on an interface falls within the allowed range.

Possible Causes

The number of CRC error packets that an interface received in a specified period fell below the upper threshold.

Procedure
  1. This trap message is informational only, and no action is required.

DEVM_1.3.6.1.4.1.2011.5.25.41.4.5 hwIfMonitorInputRateRising

Description

Interface input flow bandwidth usage exceeded the trap threshold. (EntityPhysicalIndex=[EntityPhysicalIndex], hwIfMonitorInputRatePercentage=[hwIfMonitorInputRatePercentage], hwIfMonitorInputRateThreshold=[hwIfMonitorInputRateThreshold])

The percentage of the rate of incoming traffic to the total bandwidth on an interface exceeded the threshold.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.41.4.5

Trap severity

Major

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.41.4.6 hwIfMonitorInputRateResume

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the index of an entity.

hwIfMonitorInputRatePercentage

Indicates statistics on incoming traffic.

hwIfMonitorInputRateThreshold

Indicates alarm threshold for incoming traffic.

Impact on the System

Delay or packet loss occurred when the rate of incoming or outgoing traffic was close to alarm threshold of the total bandwidth.

Possible Causes

The percentage of the rate of incoming traffic to the total bandwidth on an interface exceeded the threshold.

Procedure
  1. Run the display this interface command in the interface view to check whether the alarm threshold is set too small. The threshold range is specified by users according to service requirements.
  • If so, go to step 2.
  • If not, go to step 3.
  1. Run the trap-threshold input-rate threshold_value command in the interface view to set the alarm threshold to a larger value. Check whether the trap is cleared.

    • If so, go to step 4.
    • If not, go to step 3.

  2. Collect traps, logs, and configurations, and contact Huawei technical support engineers.
  3. End

DEVM_1.3.6.1.4.1.2011.5.25.41.4.6 hwIfMonitorInputRateResume

Description

Interface input flow bandwidth usage resumed below the trap threshold. (EntityPhysicalIndex=[EntityPhysicalIndex], hwIfMonitorInputRatePercentage=[hwIfMonitorInputRatePercentage], hwIfMonitorInputRateThreshold=[hwIfMonitorInputRateThreshold])

The percentage of the rate of incoming traffic to the total bandwidth on an interface fell below the threshold.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.41.4.6

Trap severity

Major

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.41.4.5 hwIfMonitorInputRateRising

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the index of an entity.

hwIfMonitorInputRatePercentage

Indicates statistics on incoming traffic.

hwIfMonitorInputRateThreshold

Indicates alarm threshold for incoming traffic.

Impact on the System

None

Possible Causes

The percentage of the rate of incoming traffic to the total bandwidth on an interface fell below the threshold.

Procedure
  • This trap message is informational only, and no action is required.

DEVM_1.3.6.1.4.1.2011.5.25.41.4.7 hwIfMonitorOutputRateRising

Description

Interface output flow bandwidth usage exceeded the trap threshold. (EntityPhysicalIndex=[EntityPhysicalIndex], hwIfMonitorOutputRatePercentage=[hwIfMonitorOutputRatePercentage], hwIfMonitorOutputRateThreshold=[hwIfMonitorOutputRateThreshold])

The percentage of the rate of outgoing traffic to the total bandwidth on an interface exceeded the threshold.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.41.4.7

Trap severity

Major

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.41.4.8 hwIfMonitorOutputRateResume

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the index of an entity.

hwIfMonitorInputRatePercentage

Indicates statistics on incoming traffic.

hwIfMonitorInputRateThreshold

Indicates alarm threshold for incoming traffic.

Impact on the System

Delay or packet loss occurred when the rate of incoming or outgoing traffic was close to 100% of the total bandwidth.

Possible Causes

The percentage of the rate of incoming traffic to the total bandwidth on an interface exceeded the threshold.

Procedure
  1. Run the display this interface command in the interface view to check whether the alarm threshold is set too small. The threshold range is specified by users according to service requirements.
  • If so, go to step 2.
  • If not, go to step 3.
  1. Run the trap-threshold input-rate threshold_value command in the interface view to set the alarm threshold to a larger value. Check whether the trap is cleared.

    • If so, no action is required.
    • If not, go to step 3.

  2. Collect traps, logs, and configurations, and contact Huawei technical support engineers.

DEVM_1.3.6.1.4.1.2011.5.25.41.4.8 hwIfMonitorOutputRateResume

Description

Interface output flow bandwidth usage resumed below the trap threshold. (INDEX=[EntityPhysicalIndex], hwIfMonitorOutputRatePercentage=[hwIfMonitorOutputRatePercentage], TrapThreshold=[hwIfMonitorOutputRateThreshold])

The percentage of the rate of outgoing traffic to the total bandwidth on an interface fell below the threshold.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.41.4.8

Trap severity

Major

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.41.4.7 hwIfMonitorOutputRateRising

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the index of an entity.

hwIfMonitorInputRatePercentage

Indicates statistics on incoming traffic.

hwIfMonitorInputRateThreshold

Indicates alarm threshold for incoming traffic.

Impact on the System

None

Possible Causes

The percentage of the rate of outgoing traffic to the total bandwidth on an interface fell below the threshold.

Procedure
  • This trap message is informational only, and no action is required.

DEVM_1.3.6.1.4.1.2011.5.25.219.2.2.3 hwBoardFail

Description

The board partially failed. (EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalIndex=[EntPhysicalIndex], EntPhysicalName=[EntPhysicalName], EntityType=[EntityType], EntityTrapFaultID=[EntityTrapFaultID], Reason=[Reason])

The device partially failed.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.219.2.2.3

Trap severity

Critical

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.219.2.2.4 hwBoardFailResume

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the index of an entity.

EntPhysicalIndex

Indicates the index of an entity.

EntPhysicalName

Indicates the name of an entity.

EntityType

Indicates the entity type.

EntityTrapFaultID

Indicates the error code.

  • 132110
  • 132112
  • 132105
  • 132127
  • 132120
  • 132137
  • 132162

Reason

Indicates a possible cause.

Impact on the System

Services on the device may be affected or interrupted.

Possible Causes

Cause 1 (EntityTrapFaultID=[132110]): The voltage exceeded the upper limit of the fatal threshold.

Cause 2 (EntityTrapFaultID=[132112]): The voltage fell below the lower limit of the fatal threshold.

Cause 3 (EntityTrapFaultID=[132105]): The sensor on the board failed.

Cause 4 (EntityTrapFaultID=[132127]): LSW 156.25 M clock failed.

Cause 5 (EntityTrapFaultID=[132120]): IIC failed.

Cause 6 (EntityTrapFaultID=[132137]): The chip failed.

Cause 7 (EntityTrapFaultID=[132162]): The fan or power module model did not match the device model.

Procedure
  • Cause 1: The voltage exceeded the upper limit of the fatal threshold.
    1. Check the voltage of the device. If the voltage fault cannot be rectified in a timely manner, replace the device.
  • Cause 2: The voltage fell below the lower limit of the fatal threshold.
    1. Check the voltage of the device.
    2. Check whether the voltage of the external power supply is sufficient.
      • If so, go to step 4.
      • If not, go to step 3.
    3. Increase the voltage of the power supply.
    4. Replace the device.
  • Cause 3: The sensor on the board failed.
    1. Collect traps, logs, and configurations, and contact Huawei technical support engineers.
  • Cause 4: LSW 156.25 M clock failed.
    1. Collect traps, logs, and configurations, and contact Huawei technical support engineers.
  • Cause 5: IIC failed.
    1. Collect traps, logs, and configurations, and contact Huawei technical support engineers.
  • Cause 6: The chip failed.
    1. Collect traps, logs, and configurations, and contact Huawei technical support engineers.
  • Cause 7: The fan or power module model did not match the device model.
    1. Replace existing fans or power modules with ones that match the device.

DEVM_1.3.6.1.4.1.2011.5.25.219.2.2.4 hwBoardFailResume

Description

The board resumed from partial failure. (EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalIndex=[EntPhysicalIndex], EntPhysicalName=[EntPhysicalName], EntityType=[EntityType], EntityTrapFaultID=[EntityTrapFaultID], Reason=[Reason])

The device recovered from a partial failure.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.219.2.2.4

Trap severity

Critical

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.219.2.2.3 hwBoardFail

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the index of an entity.

EntPhysicalIndex

Indicates the index of an entity.

EntPhysicalName

Indicates the name of an entity.

EntityType

Indicates the entity type.

EntityTrapFaultID

Indicates the error code.

  • 132110
  • 132112
  • 132105
  • 132127
  • 132120
  • 132137
  • 132162

Reason

Indicates a possible cause.

Impact on the System

Some services on the device recover.

Possible Causes

The device recovered from a partial failure.

Procedure
  1. This trap message is informational only, and no action is required.

DEVM_1.3.6.1.4.1.2011.5.25.219.2.2.5 hwBoardInvalid

Description

The board totally failed. (EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalIndex=[EntPhysicalIndex],EntPhysicalName=[EntPhysicalName], EntityType=[EntityType], EntityTrapFaultID=[EntityTrapFaultID], Reason=[Reason])

The device completely failed.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.219.2.2.5

Trap severity

Critical

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.219.2.2.6 hwBoardInvalidResume

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the index of an entity.

EntPhysicalIndex

Indicates the index of an entity.

EntPhysicalName

Indicates the name of an entity.

EntityType

Indicates the entity type.

EntityTrapFaultID

Indicates the error code.

  • 132614
  • 132616
  • 132625
  • 132626
  • 132627

Reason

Indicates a possible cause.

Impact on the System

The device completely fails, and services are interrupted.

Possible Causes

Cause 1 (EntityTrapFaultID=[132614]): The EPLD logic of the board failed.

Cause 2 (EntityTrapFaultID=[132616]): The clock signals of the board were incorrect.

Cause 3 (EntityTrapFaultID=[132625]): The Lanswitch chip of the board failed.

Cause 4 (EntityTrapFaultID=[132627]): The board registered fail.

Cause 5 (EntityTrapFaultID=[132626]): The board was powered off because the board temperature was too high.

Procedure
  • Cause 1: The EPLD logic of the board failed.
    1. Check whether the faulty device is the active device
      • If so, perform the active/standby switchover when the standby device works properly.
      • If not, go to step 2.
    2. Check whether the board has been successfully registered.
      • If so, replace the faulty device.
      • If not, go to step 3.
    3. Power off and then power on the faulty device. If the faulty device cannot be registered or the fault persists after the device is registered, replace the faulty device.
  • Cause 2: The clock signals of the board were incorrect.

    The handling procedure is the same as that for cause 1.

  • Cause 3: The Lanswitch chip of the board failed.
    1. Run the display device [ slot slot-id ] command to check the status of all devices on the device.
      • If all devices are registered, go to step 2.
      • If any device is unregistered, replace the faulty device.
    2. Collect traps, logs, and configurations, and contact Huawei technical support engineers.
  • Cause 4: The board registered fail.

    This trap message is informational only, and no action is required.

  • Cause 5: The board was powered off.
    1. Replace the device, and check whether the fault is rectified.
      • If so, no action is required.
      • If not, go to step 2.
    2. Collect traps, logs, and configurations, and contact Huawei technical support engineers.

DEVM_1.3.6.1.4.1.2011.5.25.219.2.2.6 hwBoardInvalidResume

Description

The board resumed from total failure. (EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalIndex=[EntPhysicalIndex],EntPhysicalName=[EntPhysicalName], EntityType=[EntityType], EntityTrapFaultID=[EntityTrapFaultID], Reason=[Reason])

The board recovered from a complete failure.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.219.2.2.6

Trap severity

Critical

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.219.2.2.5 hwBoardInvalid

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the index of an entity.

EntPhysicalIndex

Indicates the index of an entity.

EntPhysicalName

Indicates the name of an entity.

EntityType

Indicates the entity type.

EntityTrapFaultID

Indicates the error code.

  • 132614
  • 132616
  • 132625
  • 132626
  • 132627

Reason

Indicates a possible cause.

Impact on the System

Services recover on the board.

Possible Causes

The board recovered from a complete failure.

Procedure
  1. This trap message is informational only, and no action is required.

DEVM_1.3.6.1.4.1.2011.5.25.219.2.4.1 hwOpticalRemove

Description

Optical Module has been removed. (EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalIndex=[EntPhysicalIndex], EntPhysicalName=[EntPhysicalName], EntityTrapFaultID=[EntityTrapFaultID], Reason=[Reason])

The optical module was removed.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.219.2.4.1

Trap severity

Critical

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.219.2.4.2 hwOpticalInsert

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the entity index.

EntPhysicalIndex

Indicates the entity index.

EntPhysicalName

Indicates the name of an entity.

EntityTrapFaultID

Indicates the error code: 135680.

Reason

Indicates a possible cause.

Impact on the System

Services on the corresponding interfaces are interrupted.

Possible Causes

The optical module was removed.

Procedure
  • Install the corresponding optical module.

DEVM_1.3.6.1.4.1.2011.5.25.219.2.4.2 hwOpticalInsert

Description

Optical Module has been inserted. (EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalIndex=[EntPhysicalIndex], EntPhysicalName=[EntPhysicalName], EntityTrapFaultID=[EntityTrapFaultID], Reason=[Reason])

An optical module was installed.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.219.2.4.2

Trap severity

Critical

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.219.2.4.1 hwOpticalRemove

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the entity index.

EntPhysicalIndex

Indicates the entity index.

EntPhysicalName

Indicates the name of an entity.

EntityTrapFaultID

Indicates the error code: 135680.

Reason

Indicates a possible cause.

Impact on the System

None

Possible Causes

An optical module was installed.

Procedure
  • This trap message is informational only, and no action is required.

DEVM_1.3.6.1.4.1.2011.5.25.219.2.4.5 hwOpticalInvalid

Description

Optical Module is invalid. (EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalIndex=[EntPhysicalIndex], EntPhysicalName=[EntPhysicalName], EntityTrapFaultID=[EntityTrapFaultID], Reason=[Reason])

An error occurred on the optical module.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.219.2.4.5

Trap severity

Warning

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.219.2.4.6 hwOpticalInvalidResume

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the entity index.

EntPhysicalIndex

Indicates the entity index.

EntPhysicalName

Indicates the name of an entity.

EntityTrapFaultID

Indicates the error code.

  • 136193
  • 136194
  • 136195
  • 136196
  • 136203

Reason

Indicates a possible cause.

Impact on the System

Services on the optical module may be affected, which probably leads to error codes, error packets, or even service interruption.

Possible Causes

Cause 1 (EntityTrapFaultID=[136193]): The transmit power of the optical module was too high.

Cause 2 (EntityTrapFaultID=[136194]): The transmit power of the optical module was too low.

Cause 3 (EntityTrapFaultID=[136195]): The receive power of the optical module was too high.

Cause 4 (EntityTrapFaultID=[136196]): The receive power of the optical module was too low.

Cause 5 (EntityTrapFaultID=[136203]): An incorrect optical module was installed.

Procedure
  • Cause 1: The transmit power of the optical module was too high.
    1. Run the display interface command in the user view to check whether the transmit power Tx Power of the local interface is within the allowed range.
      • If so, Collect traps, logs, and configurations, and contact Huawei technical support engineers, and go to step 3.
      • If not, replace the optical module.
    2. If the fault persists, collect traps, logs, and configurations and contact Huawei technical support engineers.
    3. End
  • Cause 2: The transmit power of the optical module was too low.
    1. Run the display interface command in the user view to check whether the transmit power Tx Power of the local interface is within the allowed range.
      • If so, go to step 2.
      • If not, replace the optical module.
    2. Collect traps, logs, and configurations, and contact Huawei technical support engineers.
  • Cause 3: The receive power of the optical module was too high.
    1. Run the display interface command in the user view to check whether the receive power Rx Power of the local interface is within the allowed range.
      • If so, collect traps, logs, and configurations, contact Huawei technical support engineers, and go to step 7.
      • If so, go to step 2.
    2. Check whether a trap is generated for high transmit optical power on the peer optical module.
      • If so, rectify the peer optical module fault first, and go to step 7.
      • If not, go to step 3.
    3. Check whether the peer optical module matches the local optical module.
      • If not, replace the local optical module to match the peer optical module, and go to step 7.
      • If not, go to step 4.
    4. Add optical attenuator to the local optical module by -5 dBm (recommended).
    5. If the fault persists, replace the optical module.
    6. If the fault persists, collect traps, logs, and configurations and contact Huawei technical support engineers.
    7. End
  • Cause 4: The receive power of the optical module was too low.
    1. Run the display interface command in the user view to check whether the receive power Rx Power of the local interface is within the allowed range.
      • If so, collect traps, logs, and configurations, contact Huawei technical support engineers, and go to step 7.
      • If so, go to step 2.
    2. If no trap on low receive optical power is generated and the peer interface is Up, go to step 4.
    3. If the peer interface is Up, and the trap is cleared, go to step 7.
    4. Check whether the optical fiber is in good condition. If not, replace the fiber.
    5. Check whether the local interface generates a trap message. If so, replace the optical module of the local interface.
    6. If the fault persists after the optical module is replaced, collect traps, logs, and configurations, and contact Huawei technical support engineers.
    7. End
  • Cause 5: An incorrect optical module was installed.
    1. Check whether the optical module is Huawei certified optical module.
    2. Check whether the local interface generates a trap message. If so, replace the optical module of the local interface.
    3. Check whether the peer interface generates a trap message. If so, replace the optical module of the peer interface.
    4. If the fault persists after the optical module is replaced, collect alarms, logs, and configurations, and contact Huawei technical support engineers.

DEVM_1.3.6.1.4.1.2011.5.25.219.2.4.6 hwOpticalInvalidResume

Description

Optical Module resume from invalid situation. (EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalIndex=[EntPhysicalIndex], EntPhysicalName=[EntPhysicalName], EntityTrapFaultID=[EntityTrapFaultID], Reason=[Reason])

The fault on the optical module was rectified.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.219.2.4.6

Trap severity

Warning

Matching trap

DEVM_1.3.6.1.4.1.2011.5.25.219.2.4.5 hwOpticalInvalid

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the entity index.

EntPhysicalIndex

Indicates the entity index.

EntPhysicalName

Indicates the name of an entity.

EntityTrapFaultID

Indicates the error code.

  • 136193
  • 136194
  • 136195
  • 136196
  • 136203

Reason

Indicates a possible cause.

Impact on the System

None

Possible Causes

The fault on the optical module was rectified.

Procedure
  • This trap message is informational only, and no action is required.
Translation
Download
Updated: 2018-08-16

Document ID: EDOC1000015902

Views: 192299

Downloads: 1565

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next