No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

E9000 Server V100R001 HMM Alarm Handling 19

This document describes E9000 server alarms in terms of the meaning, impact on the system, possible causes, and solutions.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
DRIVER

DRIVER

DRIVER_1.3.6.1.4.1.2011.5.25.31.2.2.2 hwBoardSplitPorts

Trap Buffer Description

Split ports exist on the board.(hwPhysicalName = [hwPhysicalName])

The split ports exist on the board.

Trap Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.31.2.2.2

Trap level

Notice

Trap Buffer Parameters

Parameter

Meaning

hwPhysicalName

Indicates the board name.

Impact on the System

None

Possible Causes

The split ports exist on the board.

Procedure
  1. This log message is informational only, and no action is required.

DRIVER_1.3.6.1.4.1.2011.5.25.219.2.2.7 hwBoardLeaveMaster

Description

Board leave master state. (EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalIndex=[EntPhysicalIndex], EntPhysicalName=[EntPhysicalName], EntityType=[EntityType], EntityTrapFaultID=[EntityTrapFaultID],Reason=Master/Slave Board Switchover.)

The active device was not running in the active state.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.219.2.2.7

Trap severity

Warning

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the index of an entity.

EntPhysicalIndex

Indicates the index of an entity.

EntPhysicalName

Indicates the name of an entity.

EntityType

Indicates the entity type.

EntityTrapFaultID

Indicates the error code: 133120.

Reason

Indicates a possible cause.

Impact on the System

If no active/standby switchover is performed, the active device may be faulty.

Possible Causes

The master/slave switchover was performed or the active device was faulty.

Procedure
  1. Check whether active/standby switchover was performed.
  • If so, no action is required.
  • If not, go to step 2.
  1. Run the display device [ slot slot-id ] command to check whether the original active device has been registered successfully.

    • If so, go to step 4.
    • If not, go to step 3.

  2. Remove and install the original active device. After the device is started successfully, check whether the device is registered successfully.

    • If so, go to step 4.
    • If not, go to step 5.

  3. Check whether the original active device is faulty. Check whether the active/standby switchover can be performed.

    • If so, go to step 6.
    • If not, go to step 5.

  4. Collect traps, logs, and configurations, and contact Huawei technical support engineers.
  5. End

DRIVER_1.3.6.1.4.1.2011.5.25.219.2.2.8 hwBoardBecomeMaster

Description

Board changed to the master state. (EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalIndex=[EntPhysicalIndex], EntPhysicalName=[EntPhysicalName], EntityType=[EntityType], EntityTrapFaultID=[EntityTrapFaultID],Reason=Master/Slave Board Switchover.)

The standby device became the active device.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.219.2.2.8

Trap severity

Warning

Parameters

Name

Meaning

EntityPhysicalIndex

Indicates the index of an entity.

EntPhysicalIndex

Indicates the index of an entity.

EntPhysicalName

Indicates the name of an entity.

EntityType

Indicates the entity type.

EntityTrapFaultID

Indicates the error code: 133120.

Reason

Indicates a possible cause.

Impact on the System

If no active/standby switchover is performed, the active device may be faulty.

Possible Causes

The master/slave switchover was performed or the active device was faulty.

Procedure
  1. Check whether active/standby switchover was performed.
  • If so, no action is required.
  • If not, go to step 2.
  1. Run the display device [ slot slot-id ] command to check whether the original active device has been registered successfully.

    • If so, go to step 4.
    • If not, go to step 3.

  2. Remove and install the original active device. After the device is started successfully, check whether the device is registered successfully.

    • If so, go to step 4.
    • If not, go to step 5.

  3. Check whether the original active device is faulty. Check whether the active/standby switchover can be performed.

    • If so, go to step 6.
    • If not, go to step 5.

  4. Collect traps, logs, and configurations, and contact Huawei technical support engineers.
  5. End

DRIVER_1.3.6.1.4.1.2011.5.25.219.2.10.25 hwEntityDyingGaspEvent

Trap Buffer Description

Dying gasp event is occurred.(hwEntityTrapRelativeResource=[hwEntityTrapRelativeResource], hwEntityTrapReasonDescr=A power cable is loose, an external power cable is faulty, or a power supply module is faulty)

A dying gasp event is generated.

Trap Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.219.2.10.25

Trap level

Critical

Trap Buffer Parameters

Parameter

Meaning

hwEntityTrapRelativeResource

System MAC address.

hwEntityTrapReasonDescr

Reason.

Impact on the System

The device is powered off or restarted.

NOTE:

This event may trigger two alarms of the same content.

Possible Causes
  • The power cable is loose.
  • The external power cable is faulty.
  • The power module is faulty.
Procedure
  1. Check whether the power cable is loose.
  • If so, insert the power cable tightly.
  • If not, go to step 2.
  1. Check whether external power supply is normal.

    • If so, go to step 3.
    • If not, solve the external power supply problem.

  2. Check whether the power module is faulty.

    • If so, replace the power module.
    • If not, go to step 4.

  3. Collect alarms, logs, and configurations, and contact Huawei technical support personnel.
Translation
Download
Updated: 2018-08-16

Document ID: EDOC1000015902

Views: 192014

Downloads: 1565

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next