No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

E9000 Server V100R001 HMM Alarm Handling 19

This document describes E9000 server alarms in terms of the meaning, impact on the system, possible causes, and solutions.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ETRUNK

ETRUNK

ETRUNK_1.3.6.1.4.1.2011.5.25.178.2.1 hwETrunkStatusChange

Description

The status of an E-Trunk changed.(ETrunkId=[INTEGER], State=[STRING], StateReason=[STRING])

The E-Trunk status change was notified to the NMS.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.178.2.1

Trap severity

Warning

Parameters

Parameter

Description

ETrunkId

E-Trunk ID

State

E-Trunk status

  • initialize(1)
  • backup(2)
  • master(3)

StateReason

Reason for the E-Trunk being in this status

Impact on the System

The system will not be affected.

Possible Causes

Cause 1: PRI (The master/backup status change is determined based on the priorities.)

Cause 2: INIT (The E-Trunk is undergoing initialization.)

Cause 3: PEER_NODE_DOWN (The remote device in the E-Trunk fails.)

Procedure
  • Cause 1: PRI
    1. Check whether the E-Trunk master/backup status change is required. If it is not required, go to Step 2.
    2. Run the display e-trunk etrunk-id command to check whether the E-Trunk priority is changed.
      • If the E-Trunk priority is changed, check whether the priority change is required. If the priority change is not required, go to Step 3.
      • If the E-Trunk priority is not changed, go to Step 4.
    3. Run the priority priority command in the E-Trunk view to configure the E-Trunk priority based on the networking. Then, check whether the alarm is cleared. If the alarm persists, go to Step 4.
    4. Collect log information and contact Huawei technical support personnel.
  • Cause 2: INIT
    1. Check whether the ongoing E-Trunk initialization is normal. If the ongoing E-Trunk initialization is not normal, go to Step 2.
    2. Collect log information and contact Huawei technical support personnel.
  • Cause 3: PEER_NODE_DOWN
    1. Check whether the interface is shut down.
      • If the interface is shut down, go to Step 2.
      • If the interface is not shut down, go to Step 3.
    2. Run the undo shutdown command in the interface view. Then, check whether the alarm is cleared. If the alarm persists, go to Step 3.
    3. Check the physical link and repair it if faulty. If the alarm persists, go to Step 4.
    4. Collect log information and contact Huawei technical support personnel.

ETRUNK_1.3.6.1.4.1.2011.5.25.178.2.2 hwETrunkMemberStatusChange

Description

The status of an E-Trunk member interface changed. (ETrunkId=[INTEGER], MemberType=[STRING], MemberId=[INTEGER], State=[STRING], StateReason=[STRING])

The status of an E-Trunk member interface has changed.

Attribute

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.178.2.2

Trap severity

Warning

Parameters

Parameter

Description

ETrunkId

ID of the E-Trunk to which the member interface belongs

MemberType

Member interface type. Currently, only the Eth-Trunk interface is supported.

MemberId

Member interface ID

State

Member interface status

StateReason

Reason for the member interface being in this state

Impact on the System

The system will not be affected.

Possible Causes

Cause 1: ETRUNK_INIT (The E-Trunk is undergoing initialization.)

Cause 2: ETRUNK_BACKUP (The E-Trunk works in backup mode.)

Cause 3: ETRUNK_MASTER (The E-Trunk works in master mode.)

Cause 4: PEER_MEMBER_DOWN (The peer Eth-Trunk interface goes Down.)

Cause 5: PEER_MEMBER_UP (The peer Eth-Trunk interface goes Up.)

Cause 6: ACTIVE_ACTIVE (The Eth-Trunk links work in active-active mode.)

Cause 7: DEGRADED_ACTIVE: (The Eth-Trunk links no longer work in active-active mode because the local or remote nickname or the pseudo nickname changes.)

Cause 8: PEERLINK_DOWN (The peer-link fails.)

Procedure
  • Cause : ETRUNK_INIT

    See the troubleshooting steps in ETRUNK_1.3.6.1.4.1.2011.5.25.178.2.1 hwETrunkStatusChange.

  • Cause : ETRUNK_BACKUP

    See the troubleshooting steps in ETRUNK_1.3.6.1.4.1.2011.5.25.178.2.1 hwETrunkStatusChange.

  • Cause : ETRUNK_MASTER

    See the troubleshooting steps in ETRUNK_1.3.6.1.4.1.2011.5.25.178.2.1 hwETrunkStatusChange.

  • Cause : PEER_MEMBER_DOWN
    1. Check whether the peer interface is shut down.
      • If the peer interface is shut down, go to Step 2.
      • If the peer interface is not shut down, go to Step 3.
    2. Run the undo shutdown command in the interface view. Then, check whether the alarm is cleared. If the alarm persists, go to Step 3.
    3. Check the physical link and repair it if faulty. If the alarm persists, go to Step 4.
    4. Collect log information and contact Huawei technical support personnel.
  • Cause 5: PEER_MEMBER_UP

    The alarm is informational only, and no action is required.

  • Cause 6: ACTIVE_ACTIVE

    The alarm is informational only, and no action is required.

  • Cause 7: DEGRADED_ACTIVE
    1. Check whether the local or remote nickname or the pseudo nickname is changed.
      • If the local or remote nickname or the pseudo nickname is changed, adjust it and check whether the alarm persists. If the alarm persists, go to Step 2.
      • If the local or remote nickname or the pseudo nickname is not changed, go to Step 2.
    2. Collect log information and contact Huawei technical support personnel.
  • Cause 8: PEERLINK_DOWN
    1. Check whether the peer interface is shut down.
      • If the peer interface is shut down, go to Step 2.
      • If the peer interface is not shut down, go to Step 3.
    2. Run the undo shutdown command in the interface view. Then, check whether the alarm is cleared. If the alarm persists, go to Step 3.
    3. Check the physical link and repair it if faulty. If the alarm persists, go to Step 4.
    4. Collect log information and contact Huawei technical support personnel.
Translation
Download
Updated: 2018-08-16

Document ID: EDOC1000015902

Views: 193063

Downloads: 1567

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next