No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

E9000 Server V100R001 HMM Alarm Handling 19

This document describes E9000 server alarms in terms of the meaning, impact on the system, possible causes, and solutions.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
NQA

NQA

NQA_1.3.6.1.2.1.80.0.1 pingProbeFailed

Description

Ping entry probe failed. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], OperStatus=[OperStatus], AddressType=[AddressType], Address=[Address], MinRtt=[MinRtt], MaxRtt=[MaxRtt], AverageRtt=[AverageRtt], ProbeResponses=[ProbeResponses], SentProbes=[SentProbes], RttSumOfSquares=[RttSumOfSquares], LastGoodProbe=[LastGoodProbe])

The number of consecutive probe failures reached the configured upper threshold.

Attributes

Attribute

Description

Trap OID

1.3.6.1.2.1.80.0.1

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Administrator of an NQA test instance

TestName

Name of an NQA test instance

TargetAddressType

Destination address type of an NQA test instance

TargetAddress

Destination address of an NQA test instance

OperStatus

Status of an NQA test instance

AddressType

Address type of an NQA test instance

Address

Address of an NQA test instance

MinRtt

Minimum RTT value of an NQA test instance

MaxRtt

Maximum RTT value of an NQA test instance

AverageRtt

Average RTT value of an NQA test instance

ProbeResponses

Statistics on received packets

SentProbes

Statistics on sent packets

RttSumOfSquares

Sum of RTT squared right 32 bits

LastGoodProbe

Time when the latest returned packet is received

Impact on the System

None

Possible Causes

1.

The destination address was inexistent and unreachable.

2.

The destination address exists, but the route was unreachable.

3.

Because of the network latency, the Rtt of the packet was longer than the set timeout period.

Procedure
  1. Run the display this command in the NQA test view to check whether the destination address is correctly configured
  • If so, go to Step 2.
  • If not, run the destination-address command in the NQA test view to modify the destination address. Perform the test again to check whether the alarm is cleared.
    • If so, go to Step 5.
    • If not, go to Step 2.
  1. Run the ping command in the NQA test view to check whether the route is reachable.

    • If the route is reachable, go to Step 3.
    • If the destination address is correctly configured, but the route is not reachable, run the display ip routing-table command to check and routing table and rectify the routing fault. Perform the test again to check whether the alarm is cleared.
      • If so, go to Step 5.
      • If not, go to Step 3.

  2. Run the timeout command in the NQA test view to modify the timeout period according to the status of the current network. It is recommended that you modify the timeout period to the default value, that is, three seconds. The value of the timeout period ranges from 1 second to 60 seconds. You can run the display this command in the NQA test view to see the current timeout period.

    Perform the test again to check whether the alarm is cleared.

    • If so, go to Step 5.
    • If not, go to Step 4.

  3. Contact Huawei technical support personnel.
  4. End.

NQA_1.3.6.1.2.1.80.0.2 pingTestFailed

Description

Ping entry test failed. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], OperStatus=[OperStatus], AddressType=[AddressType], Address=[Address], MinRtt=[MinRtt], MaxRtt=[MaxRtt], AverageRtt=[AverageRtt], ProbeResponses=[ProbeResponses], SentProbes=[SentProbes], RttSumOfSquares=[RttSumOfSquares], LastGoodProbe=[LastGoodProbe])

The number of consecutive test failures reached the upper threshold.

Attributes

Attribute

Description

Trap OID

1.3.6.1.2.1.80.0.2

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Administrator of an NQA test instance

TestName

Name of an NQA test instance

TargetAddressType

Destination address type of an NQA test instance

TargetAddress

Destination address of an NQA test instance

OperStatus

Status of an NQA test instance

AddressType

Address type of an NQA test instance

Address

Address of an NQA test instance

MinRtt

Minimum RTT value of an NQA test instance

MaxRtt

Maximum RTT value of an NQA test instance

AverageRtt

Average RTT value of an NQA test instance

ProbeResponses

Statistics on received packets

SentProbes

Statistics on sent packets

RttSumOfSquares

Sum of RTT squared right 32 bits

LastGoodProbe

Time when the latest returned packet is received

Impact on the System

None.

Possible Causes

1.

The destination address was inexistent and unreachable.

2.

The destination address exists, but the route was unreachable.

3.

Because of the network latency, the Rtt of the packet was longer than the set timeout period.

Procedure
  1. Run the display this command in the NQA test view to check whether the destination address is correctly configured
  • If so, go to Step 2.
  • If not, run the destination-address command in the NQA test view to modify the destination address. Perform the test again to check whether the alarm is cleared.
    • If so, go to Step 5.
    • If not, go to Step 2.
  1. Run the ping command in the NQA test view to check whether the route is reachable.

    • If the route is reachable, go to Step 3.
    • If the destination address is correctly configured, but the route is not reachable, run the display ip routing-table command to check and routing table and rectify the routing fault. Perform the test again to check whether the alarm is cleared.
      • If so, go to Step 5.
      • If not, go to Step 3.

  2. Run the timeout command in the NQA test view to modify the timeout period according to the status of the current network. It is recommended that you modify the timeout period to the default value, that is, three seconds. The value of the timeout period ranges from 1 second to 60 seconds. You can run the display this command in the NQA test view to see the current timeout period.

    Perform the test again to check whether the alarm is cleared.

    • If so, go to Step 5.
    • If not, go to Step 4.

  3. Contact Huawei technical support personnel.
  4. End.

NQA_1.3.6.1.2.1.80.0.3 pingTestCompleted

Description

Ping entry test completed. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], OperStatus=[OperStatus], AddressType=[AddressType], Address=[Address], MinRtt=[MinRtt], MaxRtt=[MaxRtt], AverageRtt=[AverageRtt], ProbeResponses=[ProbeResponses], SentProbes=[SentProbes], RttSumOfSquares=[RttSumOfSquares], LastGoodProbe=[LastGoodProbe])

A ping test succeeded.

Attributes

Attribute

Description

Trap OID

1.3.6.1.2.1.80.0.3

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Administrator of an NQA test instance

TestName

Name of an NQA test instance

TargetAddressType

Destination address type of an NQA test instance

TargetAddress

Destination address of an NQA test instance

OperStatus

Status of an NQA test instance

AddressType

Address type of an NQA test instance

Address

Address of an NQA test instance

MinRtt

Minimum RTT value of an NQA test instance

MaxRtt

Maximum RTT value of an NQA test instance

AverageRtt

Average RTT value of an NQA test instance

ProbeResponses

Statistics on received packets

SentProbes

Statistics on sent packets

RttSumOfSquares

Sum of RTT squared right 32 bits

LastGoodProbe

Time when the latest returned packet is received

Impact on the System

None.

Possible Causes

A ping test succeeded.

Procedure
  1. The log is informational only, and no action is required.

NQA_1.3.6.1.4.1.2011.5.25.111.6.1 nqaResultsProbeFailed

Description

NQA entry probe failed. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], OperStatus=[OperStatus], Index=[Index], HopIndex=[HopIndex], AddressType=[AddressType], Address=[Address], CompletionTimeMin=[CompletionTimeMin], CompletionTimeMax=[CompletionTimeMax], SumCompletionTime=[SumCompletionTime], ProbeResponses=[ProbeResponses], SentProbes=[SentProbes], SumCompletionTime2Low=[SumCompletionTime2Low], SumCompletionTime2High=[SumCompletionTime2High], LastGoodProbe=[LastGoodProbe], LastGoodPath=[LastGoodPath])

Indicates that the number of continuous probe failures in a test reaches the set threshold. The value of the default threshold was 1. The probe-failtimes command could modify the threshold.

Attributes

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.111.6.1

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Administrator of an NQA test instance

TestName

Name of an NQA test instance

TargetAddressType

Destination address type of an NQA test instance

TargetAddress

Destination address of an NQA test instance

OperStatus

Status of an NQA test instance

Index

Index of the result table

HopIndex

Hop index

AddressType

Address type of an NQA test instance

Address

Address of an NQA test instance

CompletionTimeMin

Minimum RTT value of an NQA test instance

CompletionTimeMax

Maximum RTT value of an NQA test instance

SumCompletionTime

RTT sum of an NQA test instance.

ProbeResponses

Statistics on received packets

SentProbes

Statistics on sent packets

SumCompletionTime2Low

Sum of RTT squared right 32 bits

SumCompletionTime2High

Sum of RTT squared left 32 bits

LastGoodProbe

Time when the latest returned packet is received

LastGoodPath

Time when the last complete path is obtained

Impact on the System

None.

Possible Causes

1.

The destination address was inexistent and unreachable.

2.

The destination address exists, but the route was unreachable.

3.

Because of the network latency, the Rtt of the packet was longer than the set timeout period.

Procedure
  1. Run the display this command in the NQA test view to check whether the destination address is correctly configured
  • If so, go to Step 2.
  • If not, run the destination-address command in the NQA test view to modify the destination address. Perform the test again to check whether the alarm is cleared.
    • If so, go to Step 5.
    • If not, go to Step 2.
  1. Run the ping command in the NQA test view to check whether the route is reachable.

    • If the route is reachable, go to Step 3.
    • If the destination address is correctly configured, but the route is not reachable, run the display ip routing-table command to check and routing table and rectify the routing fault. Perform the test again to check whether the alarm is cleared.
      • If so, go to Step 5.
      • If not, go to Step 3.

  2. Run the timeout command in the NQA test view to modify the timeout period according to the status of the current network. It is recommended that you modify the timeout period to the default value, that is, three seconds. The value of the timeout period ranges from 1 second to 60 seconds. You can run the display this command in the NQA test view to see the current timeout period.

    Perform the test again to check whether the alarm is cleared.

    • If so, go to Step 5.
    • If not, go to Step 4.

  3. Contact Huawei technical support personnel.
  4. End.

NQA_1.3.6.1.4.1.2011.5.25.111.6.2 nqaResultsTestFailed

Description

NQA entry test failed. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], OperStatus=[OperStatus], Index=[Index], HopIndex=[HopIndex], AddressType=[AddressType], Address=[Address], CompletionTimeMin=[CompletionTimeMin], CompletionTimeMax=[CompletionTimeMax], SumCompletionTime=[SumCompletionTime], ProbeResponses=[ProbeResponses], SentProbes=[SentProbes], SumCompletionTime2Low=[SumCompletionTime2Low], SumCompletionTime2High=[SumCompletionTime2High], LastGoodProbe=[LastGoodProbe], LastGoodPath=[LastGoodPath])

Indicates that the number of continuous testing failures in a test instance reached the set threshold. The value of the default threshold was 1, that is, a trap was generated right after each test failure. The test-failtimes command can modify the threshold.

Attributes

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.111.6.2

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Administrator of an NQA test instance

TestName

Name of an NQA test instance

TargetAddressType

Destination address type of an NQA test instance

TargetAddress

Destination address of an NQA test instance

OperStatus

Status of an NQA test instance

Index

Index of the result table

HopIndex

Hop index

AddressType

Address type of an NQA test instance

Address

Address of an NQA test instance

CompletionTimeMin

Minimum RTT value of an NQA test instance

CompletionTimeMax

Maximum RTT value of an NQA test instance

SumCompletionTime

RTT sum of an NQA test instance.

ProbeResponses

Statistics on received packets

SentProbes

Statistics on sent packets

SumCompletionTime2Low

Sum of RTT squared right 32 bits

SumCompletionTime2High

Sum of RTT squared left 32 bits

LastGoodProbe

Time when the latest returned packet is received

LastGoodPath

Time when the last complete path is obtained

Impact on the System

None.

Possible Causes

1.

The destination address was inexistent and unreachable.

2.

The destination address exists, but the route was unreachable.

3.

Because of the network latency, the Rtt of the packet was longer than the set timeout period.

Procedure
  1. Run the display this command in the NQA test view to check whether the destination address is correctly configured
  • If so, go to Step 2.
  • If not, run the destination-address command in the NQA test view to modify the destination address. Perform the test again to check whether the alarm is cleared.
    • If so, go to Step 5.
    • If not, go to Step 2.
  1. Run the ping command in the NQA test view to check whether the route is reachable.

    • If the route is reachable, go to Step 3.
    • If the destination address is correctly configured, but the route is not reachable, run the display ip routing-table command to check and routing table and rectify the routing fault. Perform the test again to check whether the alarm is cleared.
      • If so, go to Step 5.
      • If not, go to Step 3.

  2. Run the timeout command in the NQA test view to modify the timeout period according to the status of the current network. It is recommended that you modify the timeout period to the default value, that is, three seconds. The value of the timeout period ranges from 1 second to 60 seconds. You can run the display this command in the NQA test view to see the current timeout period.

    Perform the test again to check whether the alarm is cleared.

    • If so, go to Step 5.
    • If not, go to Step 4.

  3. Contact Huawei technical support personnel.
  4. End.

NQA_1.3.6.1.4.1.2011.5.25.111.6.3 nqaResultsTestCompleted

Description

NQA entry test completed. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], OperStatus=[OperStatus], Index=[Index], HopIndex=[HopIndex], AddressType=[AddressType], Address=[Address], CompletionTimeMin=[CompletionTimeMin], CompletionTimeMax=[CompletionTimeMax], SumCompletionTime=[SumCompletionTime], ProbeResponses=[ProbeResponses], SentProbes=[SentProbes], SumCompletionTime2Low=[SumCompletionTime2Low], SumCompletionTime2High=[SumCompletionTime2High], LastGoodProbe=[LastGoodProbe], LastGoodPath=[LastGoodPath])

Indicates that a test succeeded.

Attributes

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.111.6.3

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Administrator of an NQA test instance

TestName

Name of an NQA test instance

TargetAddressType

Destination address type of an NQA test instance

TargetAddress

Destination address of an NQA test instance

OperStatus

Status of an NQA test instance

Index

Index of the result table

HopIndex

Hop index

AddressType

Address type of an NQA test instance

Address

Address of an NQA test instance

CompletionTimeMin

Minimum RTT value of an NQA test instance

CompletionTimeMax

Maximum RTT value of an NQA test instance

SumCompletionTime

RTT sum of an NQA test instance.

ProbeResponses

Statistics on received packets

SentProbes

Statistics on sent packets

SumCompletionTime2Low

Sum of RTT squared right 32 bits

SumCompletionTime2High

Sum of RTT squared left 32 bits

LastGoodProbe

Time when the latest returned packet is received

LastGoodPath

Time when the last complete path is obtained

Impact on the System

None.

Possible Causes

The test succeeded.

Procedure
  1. This trap message is informational only, and no action is required.

NQA_1.3.6.1.4.1.2011.5.25.111.6.4 nqaResultsThresholdNotification

Description

NQA entry over threshold. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], Index=[Index], HopIndex=[HopIndex], AddressType=[AddressType], Address=[Address], Threshold1=[Threshold1], RTDOverThresholds=[RTDOverThresholds], RTDOverThresholds=[RTDOverThresholds])

Indicates that the period of a test exceeded the set threshold. The threshold could be set by the user. The threshold rtd could modify the threshold.

Attributes

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.111.6.4

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Indicates the administrator of an NQA test instance.

TestName

Indicates the name of an NQA test instance.

TargetAddressType

Indicates the destination address type of an NQA test instance.

TargetAddress

Indicates the destination address of an NQA test instance.

Index

Indicates the index of the result table.

HopIndex

Indicates the hop index.

AddressType

Indicates the address type of an NQA test instance.

Address

Indicates the address of an NQA test instance.

Threshold1

Indicates the RTD threshold of an NQA test instance.

RTDOverThresholds

Indicates the maximum RTT value of an NQA test instance.

RTDOverThresholds

Indicates the number of times that the RTT exceeds the threshold.

Impact on the System

None.

Possible Causes

1.

The threshold was set too small.

2.

The network was busy.

Procedure
  1. Run the display cpu command in the system view to check whether the CPU has an excessive usage.
  • If so, go to Step 3.
  • If not, go to Step 2.
  1. In the NQA test view, run the display this command to know the current threshold. Then run the threshold rtd command to modify the threshold as required. The recommended value is 20 ms.

    Perform the test again to check whether the alarm is cleared.

    • If so, go to Step 4.
    • If not, go to Step 3.

  2. Contact Huawei technical support personnel.
  3. End.

NQA_1.3.6.1.4.1.2011.5.25.111.6.9 nqaJitterStatsProbeFailed

Description

NQA entry probe failed. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], OperStatus=[OperStatus], Index=[Index], RttSum=[RttSum], RttSum2Low=[RttSum2Low], RttSum2High=[RttSum2High], RttMin=[RttMin], RttMax=[RttMax], PacketOutOfSequences=[PacketOutOfSequences], Errors=[Errors], Busies=[Busies], Timeouts=[Timeouts], Drops=[Drops], ProbeResponses=[ProbeResponses], SentProbes=[SentProbes], MaxDelaySD=[MaxDelaySD], MaxDelayDS=[MaxDelayDS], JitterOut=[JitterOut], JitterIn=[JitterIn], OWSumSD=[OWSumSD], OWSumDS=[OWSumDS])

Indicates that the number of testing failures in a test instance reached the set threshold. The value of the default threshold was 1. The test-failtimes command could modify the threshold.

Attributes

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.111.6.9

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Indicates the administrator of an NQA test.

TestName

Indicates the name of an NQA test instance.

TargetAddressType

Indicates the destination address type of an NQA test instance.

TargetAddress

Indicates the destination address of an NQA test instance.

OperStatus

Indicates the status of an NQA test instance.

Index

Indicates the index of the result table.

RttSum

Indicates the RTT sum of an NQA test instance.

RttSum2Low

Indicates the sum of RTT squared right 32 bits.

RttSum2High

Indicates the sum of RTT squared left 32 bits.

RttMin

Indicates the minimum RTT value of an NQA test instance.

RttMax

Indicates the maximum RTT value of an NQA test instance.

PacketOutOfSequences

Indicates the number of out-of-order packets.

Errors

Indicates the number of packets with incorrect sequence numbers.

Busies

Indicates the number of initialization or resource application failures.

Timeouts

Indicates the number of times that no response is received within the timeout period.

Drops

Indicates the number of packets failed to be sent.

ProbeResponses

Indicates the number of received packets.

SentProbes

Indicates the number of sent packets.

MaxDelaySD

Indicates the maximum OWD from the source to the destination.

MaxDelayDS

Indicates the maximum OWD from the destination to the source.

JitterOut

Indicates the jitter in sending packets.

JitterIn

Indicates the jitter in receiving packets.

OWSumSD

Indicates the sum of OWD from the source to the destination.

OWSumDS

Indicates the sum of OWD from the destination to the source.

Impact on the System

None.

Possible Causes
  • Cause 1: The destination address was inexistent and unreachable. The number of continuous test failures in a test reached the set threshold.
  • Cause 2: The destination address existed, but the route was unreachable. The number of continuous test failures in a test reached the set threshold.
Procedure
  1. Run the display this command in the NQA test view to check whether the destination address is correctly configured. If not, run the destination-address command in the NQA test view to modify the destination address.

Then, perform the test instance again to check whether the test is successful.

  • If so, go to Step 5.
  • If not, go to Step 2.
  1. Run the ping command in the NQA test view to check whether the route is reachable.

    • If the destination address is correctly configured, but the route is not reachable, run the display ip routing-table command to check and routing table and rectify the routing fault. If the test fails again, go to Step 4.
    • If the route is reachable, go to Step 3.

  2. Run the display this command in the NQA test view to check whether the destination port is correctly configured. If not, run the destination-port command in the NQA test view to modify the related parameters.

    Then, perform the test instance again to check whether the test is successful.

    • If so, go to Step 5.
    • If not, go to Step 4.

  3. Contact Huawei technical support personnel.
  4. End.

NQA_1.3.6.1.4.1.2011.5.25.111.6.10 nqaJitterStatsTestFailed

Description

The NQA entry test failed. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], OperStatus=[OperStatus], Index=[Index], RttSum=[RttSum], RttSum2Low=[RttSum2Low], RttSum2High=[RttSum2High], RttMin=[RttMin], RttMax=[RttMax], PacketOutOfSequences=[PacketOutOfSequences], Errors=[Errors], Busies=[Busies], Timeouts=[Timeouts], Drops=[Drops], ProbeResponses=[ProbeResponses], SentProbes=[SentProbes], MaxDelaySD=[MaxDelaySD], MaxDelayDS=[MaxDelayDS], JitterOut=[JitterOut], JitterIn=[JitterIn], OWSumSD=[OWSumSD], OWSumDS=[OWSumDS])

Indicates that the number of testing failures in a test instance reached the set threshold. The value of the default threshold was 1. The test-failtimes command could modify the threshold.

Attributes

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.111.6.10

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Indicates the administrator of an NQA test.

TestName

Indicates the name of an NQA test instance.

TargetAddressType

Indicates the destination address type of an NQA test instance.

TargetAddress

Indicates the destination address of an NQA test instance.

OperStatus

Indicates the status of an NQA test instance.

Index

Indicates the index of the result table.

RttSum

Indicates the RTT sum of an NQA test instance.

RttSum2Low

Indicates the sum of RTT squared right 32 bits.

RttSum2High

Indicates the sum of RTT squared left 32 bits.

RttMin

Indicates the minimum RTT value of an NQA test instance.

RttMax

Indicates the maximum RTT value of an NQA test instance.

PacketOutOfSequences

Indicates the number of out-of-order packets.

Errors

Indicates the number of packets with incorrect sequence numbers.

Busies

Indicates the number of initialization or resource application failures.

Timeouts

Indicates the number of times that no response is received within the timeout period.

Drops

Indicates the number of packets failed to be sent.

ProbeResponses

Indicates the number of received packets.

SentProbes

Indicates the number of sent packets.

MaxDelaySD

Indicates the maximum OWD from the source to the destination.

MaxDelayDS

Indicates the maximum OWD from the destination to the source.

JitterOut

Indicates the jitter in sending packets.

JitterIn

Indicates the jitter in receiving packets.

OWSumSD

Indicates the sum of OWD from the source to the destination.

OWSumDS

Indicates the sum of OWD from the destination to the source.

Impact on the System

None.

Possible Causes

This trap occurs in the NQA test.

1.

The destination address was inexistent and unreachable. The number of continuous test failures in a test reached the set threshold.

2.

The destination address existed, but the route was unreachable. The number of continuous test failures in a test reached the set threshold.

3.

The destination port was not correctly configured, which led to the connection failure.

Procedure
  1. Run the display this command in the NQA test view to check whether the destination address is correctly configured. If not, run the destination-address command in the NQA test view to modify the destination address.

Perform the test again to check whether the alarm is cleared.

  • If so, go to Step 8.
  • If not, go to Step 2.
  1. Run the ping command in the NQA test view to check whether the route is reachable.

    • If the destination address is correctly configured, but the route is not reachable, run the display ip routing-table command to check and routing table and rectify the routing fault. If the test fails again, go to Step 7.
    • If the route is reachable, go to Step 3.

  2. Run the display this command in the NQA test view to check whether the destination port is correctly configured. If not, run the destination-port command in the NQA test view to modify the related parameters.

    Perform the test again to check whether the alarm is cleared.

    • If so, go to Step 8.
    • If not, go to Step 4.

  3. Run the display this command in the system view to check the Jitter's version.

    • If the Jitter's version is 1, go to Step 7.
    • If the Jitter's version is 2, go to Step 5.

  4. Run the display nqa server command in the System view to check whether the server port is correctly configured.

    • If so, go to Step 7.
    • If not, go to Step 6.

  5. Run the nqa server udpecho in the system view to modify the server. Restart the test instance.

    Perform the test again to check whether the alarm is cleared.

    • If so, go to Step 8.
    • If not, go to Step 7.

  6. Contact Huawei technical support personnel.
  7. End.

NQA_1.3.6.1.4.1.2011.5.25.111.6.11 nqaJitterStatsTestCompleted

Description

NQA entry test completed. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], OperStatus=[OperStatus], Index=[Index], RttSum=[RttSum], RttSum2Low=[RttSum2Low], RttSum2High=[RttSum2High], RttMin=[RttMin], RttMax=[RttMax], PacketOutOfSequences=[PacketOutOfSequences], Errors=[Errors], Busies=[Busies], Timeouts=[Timeouts], Drops=[Drops], ProbeResponses=[ProbeResponses], SentProbes=[SentProbes], MaxDelaySD=[MaxDelaySD], MaxDelayDS=[MaxDelayDS], JitterOut=[JitterOut], JitterIn=[JitterIn], OWSumSD=[OWSumSD], OWSumDS=[OWSumDS])

Indicates that a test succeeded.

Attributes

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.111.6.11

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Indicates the administrator of an NQA test.

TestName

Indicates the name of an NQA test instance.

TargetAddressType

Indicates the destination address type of an NQA test instance.

TargetAddress

Indicates the destination address of an NQA test instance.

OperStatus

Indicates the status of an NQA test instance.

Index

Indicates the index of the result table.

RttSum

Indicates the RTT sum of an NQA test instance.

RttSum2Low

Indicates the sum of RTT squared right 32 bits.

RttSum2High

Indicates the sum of RTT squared left 32 bits.

RttMin

Indicates the minimum RTT value of an NQA test instance.

RttMax

Indicates the maximum RTT value of an NQA test instance.

PacketOutOfSequences

Indicates the number of out-of-order packets.

Errors

Indicates the number of packets with incorrect sequence numbers.

Busies

Indicates the number of initialization or resource application failures.

Timeouts

Indicates the number of times that no response is received within the timeout period.

Drops

Indicates the number of packets failed to be sent.

ProbeResponses

Indicates the number of received packets.

SentProbes

Indicates the number of sent packets.

MaxDelaySD

Indicates the maximum OWD from the source to the destination.

MaxDelayDS

Indicates the maximum OWD from the destination to the source.

JitterOut

Indicates the jitter in sending packets.

JitterIn

Indicates the jitter in receiving packets.

OWSumSD

Indicates the sum of OWD from the source to the destination.

OWSumDS

Indicates the sum of OWD from the destination to the source.

Impact on the System

None.

Possible Causes

The test succeeded.

Procedure
  1. This trap message is informational only, and no action is required.

NQA_1.3.6.1.4.1.2011.5.25.111.6.16 nqaJitterStatsRTDThresholdNotification

Description

The RTD of the NQA entry exceeded the configured threshold. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], Threshold=[Threshold], Index=[Index], RttMax=[RttMax], MaxDelaySD=[MaxDelaySD], MaxDelayDS=[MaxDelayDS], RTDOverThresholds=[RTDOverThresholds])

Indicates that the period of a test exceeded the set threshold. The threshold could be set by the user. You can run the threshold rtd rtd command to modify the threshold.

Attributes

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.111.6.16

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Indicates the administrator of an NQA test instance.

TestName

Indicates the name of an NQA test instance.

TargetAddressType

Indicates the destination address type of an NQA test instance.

TargetAddress

Indicates the destination address of an NQA test instance.

Threshold

Indicates the user-defined threshold of an NQA test instance.

Index

Indicates the index of the result table.

RttMax

Indicates the maximum RTT value of an NQA test instance.

MaxDelaySD

Indicates the maximum OWD from the source to the destination.

MaxDelayDS

Indicates the maximum OWD from the destination to the source.

RTDOverThresholds

Indicates the number of times that the RTT exceeds the threshold.

Impact on the System

None.

Possible Causes

1.

The threshold was set too small.

2.

The network was busy.

Procedure
  1. Run the display cpu command in the system view to check whether the CPU has an excessive usage.
  • If so, go to Step 3.
  • If not, go to Step 2.
  1. In the NQA test view, run the display this command to know the current threshold. Then run the threshold rtd command to modify the threshold as required. The recommended value is 20 ms.

    Perform the test again to check whether the alarm is cleared.

    • If so, go to Step 4.
    • If not, go to Step 3.

  2. Contact Huawei technical support personnel.
  3. End.

NQA_1.3.6.1.4.1.2011.5.25.111.6.17 nqaJitterStatsOWDThresholdNotificationSD

Description

The OWD-SD of the NQA entry exceeded the configured threshold. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], Threshold=[Threshold], Index=[Index], RttMax=[RttMax], MaxDelaySD=[MaxDelaySD], MaxDelayDS=[MaxDelayDS], OWDOverThresholdsSD=[OWDOverThresholdsSD])

Indicates that the period of a test exceeded the set threshold. The threshold could be set by the user. The threshold owd-sd command could modify the threshold.

Attributes

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.111.6.17

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Indicates the administrator of an NQA test instance.

TestName

Indicates the name of an NQA test instance.

TargetAddressType

Indicates the destination address type of an NQA test instance.

TargetAddress

Indicates the destination address of an NQA test instance.

Threshold

Indicates the user-defined threshold of an NQA test instance.

Index

Indicates the index of the result table.

RttMax

Indicates the maximum RTT value of an NQA test instance.

MaxDelaySD

Indicates the maximum OWD from the source to the destination.

MaxDelayDS

Indicates the maximum OWD from the destination to the source.

OWDOverThresholdsSD

Indicates the number of times that the OWD from the source to the destination exceeds the threshold.

Impact on the System

None.

Possible Causes

1.

The threshold was set too small.

2.

The network was busy.

Procedure
  1. Run the display cpu command in the system view to check whether the CPU has an excessive load.
  • If so, go to Step 3.
  • If not, go to Step 2.
  1. In the NQA test view, run the display this command to know the current threshold. Then run the threshold owd-sd command to modify the threshold as required. The recommended value is 20 ms.

    Perform the test again to check whether the alarm is cleared.

    • If so, go to Step 4.
    • If not, go to Step 3.

  2. Contact Huawei technical support personnel.
  3. End.

NQA_1.3.6.1.4.1.2011.5.25.111.6.18 nqaJitterStatsOWDThresholdNotificationDS

Description

The OWD-DS of the NQA entry exceeded the configured threshold. (OwnerIndex=[OwnerIndex], TestName=[TestName], TargetAddressType=[TargetAddressType], TargetAddress=[TargetAddress], Threshold=[Threshold], Index=[Index], RttMax=[RttMax], MaxDelaySD=[MaxDelaySD], MaxDelayDS=[MaxDelayDS], OWDOverThresholdsDS=[OWDOverThresholdsDS])

Indicates that the period of a test exceeded the set threshold. The threshold could be set by the user. The threshold owd-ds command could modify the threshold.

Attributes

Attribute

Description

Trap OID

1.3.6.1.4.1.2011.5.25.111.6.18

Trap severity

Warning

Parameters

Parameter

Description

OwnerIndex

Indicates the administrator of an NQA test instance.

TestName

Indicates the name of an NQA test instance.

TargetAddressType

Indicates the destination address type of an NQA test instance.

TargetAddress

Indicates the destination address of an NQA test instance.

Threshold

Indicates the user-defined threshold of an NQA test instance.

Index

Indicates the index of the result table.

RttMax

Indicates the maximum RTT value of an NQA test instance.

MaxDelaySD

Indicates the maximum OWD from the source to the destination.

MaxDelayDS

Indicates the maximum OWD from the destination to the source.

OWDOverThresholdsDS

Indicates the number of times that the OWD from the destination to the source exceeds the threshold.

Impact on the System

None.

Possible Causes

1.

The threshold was set too small.

2.

The network was busy.

Procedure
  1. Run the display cpu command in the system view to check whether the CPU has an excessive load.
  • If so, go to Step 3.
  • If not, go to Step 2.
  1. In the NQA test view, run the display this command to know the current threshold. Then run the threshold owd-ds command to modify the threshold as required. The recommended value is 20 ms.

    Perform the test again to check whether the alarm is cleared.

    • If so, go to Step 4.
    • If not, go to Step 3.

  2. Contact Huawei technical support personnel.
  3. End.
Translation
Download
Updated: 2018-08-16

Document ID: EDOC1000015902

Views: 195966

Downloads: 1571

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next