No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CX311 Switch Module V100R001C00 User Guide 22

This document describes the CX311 10GE / FCoE converged switch module of the Tecal E9000 server in terms of its features, installation, removal, and configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Removing the CX311

Removing the CX311

To replace a switch module, see section "Replacing a Switch Module" in the E9000 Server V100R001 User Guide.

Impact on the System

After the switch module is removed, all services running on the switch module stop.

Prerequisites

Tools

  • Protective gloves
  • Electrostatic discharge (ESD) gloves
  • Phillips screwdriver (PH2 is 6 mm or 0.24 in.)

Workflow

Figure 3-9 Removal process

Procedure

  1. Determine the CX311 to be removed.

    Figure 3-10 Slot numbers

  2. Determine the connection relationships between signal cables and ports on the CX311.

    Figure 3-11 Port types and numbers

    1

    BMC serial port

    2

    SYS serial port

    3

    10GE optical port

    4

    8G FC optical port

  3. (Optional) Remove a serial cable.

    Figure 3-12 Removing a serial cable
    NOTE:

    The BMC serial port and SYS serial port are standard RJ45 ports and are disconnected in the same way.

  4. Remove an optical cable and optical module.

    1. Determine the optical module type and the optical port to be removed depending on site requirements.
    2. Remove the optical cable from the optical module. See (1) and (2) in Figure 3-13.
    3. Install the dust-proof cap for the optical cable. See (3) in Figure 3-13.
      Figure 3-13 Removing an optical cable
    4. Remove the optical module horizontally from the optical port, as shown in Figure 3-14.
      NOTE:

      The methods for removing an optical cable from a 10GE optical port and an 8G FC optical port are the same.

      Figure 3-14 Removing an optical module

      If 10GE or FC optical modules and fibers have been removed and 40GE optical modules and fibers do not need to be removed, go to 5.

  5. Remove the CX311.

    1. Use a Phillips screwdriver to loosen the two M3 captive screws. See (1) in Figure 3-15.
      Figure 3-15 Removing the switch module
    2. Raise the two ejector levers on the CX311 completely and pull the switch module horizontally out of the chassis. See (2) and (3) in Figure 3-15.
    3. Lower the ejector levers on the CX311. See (4) in Figure 3-15.
      NOTICE:

      An ESD bag holds only one switch module.

    4. Place the removed switch module into an ESD bag.

  6. Install a switch module filler panel.

    1. Raise the two ejector levers on the switch module filler panel and push the filler panel horizontally into the chassis as far as it will go. See (1) in Figure 3-16.
      Figure 3-16 Installing a switch module filler panel
    2. Lower the two ejector levers on the switch module filler panel. See (2) in Figure 3-16.
    3. Use a Phillips screwdriver to tighten the two M3 captive screws on the switch module filler panel. See (3) in Figure 3-16.

Translation
Download
Updated: 2018-09-20

Document ID: EDOC1000018097

Views: 61925

Downloads: 3389

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next