No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CX311 Switch Module V100R001C00 User Guide 22

This document describes the CX311 10GE / FCoE converged switch module of the Tecal E9000 server in terms of its features, installation, removal, and configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Using the CLI to Collect FCoE Gateway Information

Using the CLI to Collect FCoE Gateway Information

Scenarios

Use the CLI to collect information about the FCoE gateway.

Prerequisites

NOTE:

If the MX510 firmware version is earlier than 9.8.2.6.0, you can use the FTP tool WFTPD to collect information. For details, see Configuring an FTP Server.

Data

Table 6-4 Data list

Parameter

Example Value

IP address

192.168.1.100

Subnet mask

255.255.255.0

Default gateway

0.0.0.0

The default user name of a switching plane is admin, and the default password is Huawei12#$.

Software

CoreFTPServer.exe or msftpsrvr.exe. The following uses msftpsrvr.exe as an example.

msftpsrvr.exe: third-party free software used to transfer files between different platforms, for example, from a switch module to a PC.

Procedure

  1. Connect a PC properly to the management network port on the server using a network cable.
  2. Configure an SFTP server. For details, see Transferring Files Using SFTP.
  3. Log in to the MX510, and access the FC switching plane CLI. For details, see Logging In to the MM910 CLI over a Network Port by Using PuTTY or Logging In to a Compute Node or a Switch Module over MM910 SOL.
  4. Set an IP address.

    1. Run the following command on the FCoE gateway CLI to query the management IP address:

      FCoE_GW: admin> show version

             ***************************************************** 
             *                                                   * 
             *       Command Line Interface SHell  (CLISH)       * 
             *                                                   * 
             ***************************************************** 
       
             SystemDescription Huawei FCoE-FC Gateway module 
             HostName            <undefined> 
             Eth1IPv4NetworkAddr 192.168.96.96 
             Eth1IPv6NetworkAddr fe80::2c0:ddff:fe24:21fe 
             MAC1Address         00:c0:dd:24:21:fe 
             WorldWideName       10:00:00:c0:dd:24:21:fd 
             SerialNumber        2198080446DQCB46F882 
             SymbolicName        FCoE_GW 
             ActiveSWVersion     V9.8.0.10.0 
             ActiveTimestamp     Fri May 17 21:19:51 2013 
             POSTStatus          Passed 
             SwitchMode          Full Fabric

      Eth1IPv4NetworkAddr specifies the management IP address.

    2. Set the management IP address so that the switch module can properly communicate with the configured SFTP server.

      FCoE_GW: admin> admin start

      FCoE_GW (admin): admin> set setup system ipv4

      Set a static IPv4 address as prompted.

      EthIPv4NetworkDiscovery (1=Static, 2=Bootp, 3=Dhcp, 4=Rarp) :1 
      EthIPv4NetworkAddress (dot-notated IP Address) : 192.168.101.123 
      EthIPv4NetworkMask (dot-notated IP Address) : 255.255.255.0 
      EthIPv4GatewayAddress (dot-notated IPv4 Address) : 192.168.101.254 
      Do you want to save and activate this system setup? (y/n): [n] y
    3. Query the static IPv4 address of the FCoE gateway.

      FCoE_GW (admin): admin> show setup system ipv4

      The command output is as follows:

      System Information 
        ------------------ 
        Eth1IPv4NetworkDiscovery  Static 
        Eth1IPv4NetworkAddress    192.168.101.123 
        Eth1IPv4NetworkMask       255.255.255.0 
        Eth1IPv4GatewayAddress    192.168.101.254     

  5. Obtain logs.

    1. Run the following command to collect logs and save the logs to the local PC:

      FCoE_GW: admin> create support

    2. Set the log collection parameters as prompted. See Figure 6-18.

      The key information in Figure 6-18 is described as follows:

      • 192.168.100.214 is the IP address of the local PC.
      • The user name and password for the SFTP server are both vxworks.
      • If you press Enter when the CLI prompts you to specify the directory for storing the dump file, the dump file is automatically downloaded to the default directory on the SFTP server.
        Figure 6-18 Collecting logs

Translation
Download
Updated: 2018-09-20

Document ID: EDOC1000018097

Views: 60320

Downloads: 3389

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next