No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CX311 Switch Module V100R001C00 User Guide 22

This document describes the CX311 10GE / FCoE converged switch module of the Tecal E9000 server in terms of its features, installation, removal, and configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Backing Up the Configuration File

Backing Up the Configuration File

Use one of the following methods to back up the converged switching plane configuration file:

  • Run the save command to save configuration data to the CX311 and MM910.
  • Run the reboot command and enter N as prompted to ensure that the configuration file is synchronized to the MM910.
  • Export the configuration file of the MM910, and download the configuration file from the MM910 to a PC by using a cross-platform file transfer tool, for example, WinSCP.

After saving configuration data for the FCoE gateway, download the configuration file from the FCoE gateway to a PC by using a cross-platform file transfer tool, for example, SFTP. For details, see Procedure.

Prerequisites

Software

WinSCP.exe (third-party free software)

Procedure

  1. Log in to the converged switching plane CLI.
  2. Log in to the FCoE gateway CLI.
  3. Log in to the MM910 CLI.
  4. Configure the converged switching plane.
  5. Configure the FCoE gateway.
  6. Save the configuration file.

    • Save the configuration file of the converged switching plane.
      1. Run the following command on the converged switching plane CLI to view the configuration file required for the next startup of the converged switching plane:

        <HUAWEI> display startup

        The command output is as follows:

        MainBoard:   Configured startup system software:        flash:/xxx.cc   
        Startup system software:                   flash:/xxx.cc   
        Next startup system software:              flash:/xxx.cc   
        Startup saved-configuration file:          NULL     
        Next startup saved-configuration file:     flash:/vrpcfg.zip 
        Startup paf file:                          default   
        Next startup paf file:                     default   
        Startup patch package:                     NULL   
        Next startup patch package:                NULL

        Next startup saved-configuration file indicates the configuration file for the next startup. The displayed information indicates that the configuration file is vrpcfg.zip.

        NOTE:

        The configuration file must be a *.zip or *.cfg file. If the configuration file is a *.dat file, ths file cannot be synchronized to the MM910.

        If the configuration file is a *.dat file, perform the following operations:

        1. Run the save Configuration file name command to convert the configuration file into a *.zip or *.cfg file.
        2. Run the startup saved-configuration Configuration file name command to set the configuration file used for the next startup to the saved *.zip or *.cfg file.

        For details, see the CX110 and CX31x Series Switch Modules V100R001C00 Command Reference.

      2. Save the converged switching plane configuration file from the CX311 to the MM910.

        <HUAWEI> save

        The command output is as follows:

        Warning: The current configuration will be written to the device. Continue? [Y/N]:Y
        Now saving the current configuration to the slot 1 
        Info: Save the configuration successfully.  
        
        begin synchronize configuration to SMM ... 
        slot 1: upload configuration to SMM successfully. 
        <HUAWEI> 
      3. Check whether the configuration file is synchronized to the MM910 successfully.

        <HUAWEI> reboot

        If the following information is displayed, the configuration file is successfully synchronized.

        slot 2: 
        Next startup system software: flash:/xxx.cc 
        Next startup saved-configuration file: flash:/vrpcfg.zip
        Next startup paf file: default 
        Next startup patch package: NULL  
        
        begin synchronize configuration to SMM ... 
        slot 2: upload configuration to SMM successfully.  
        
        System will reboot! Continue? [Y/N]:
        NOTICE:

        If a configuration file synchronization failure message is displayed, contact Huawei technical support.

      4. Enter N to reject the restart.
      5. Connect the Ethernet port on a PC to the MGMT ports on the active and standby MM910s over a local area network (LAN).
      6. Connect to the MM910 floating IP address over SSH to log in to the MM910 CLI.

        PuTTY is used as an example for login over SSH. For details, see Logging In to the MM910 CLI over a Network Port by Using PuTTY.

      7. Query the version of the MM910.

        smmget -l smm -d version

        The information is displayed as follows:

        SMM Version Information: 
        Uboot    Version :(U54)012 
        CPLD     Version :(U1082)008  121120 
        PCB      Version :SMMA REV B 
        BOM      Version : 003 
        FPGA     Version :(U1049)007  121116 
        Software Version :(U54)2.0 
        IPMI Module Built:Mar 14 2013 22:31:44

        The value of the parameter Software Version is the software version of the MM910.

      8. Select an operation based on the MM910 software version.
        • If the software version is earlier than (U54) 3.00, go to 6.i.
        • If the software version is (U54) 3.00 or later, perform 6.j to 6.k.
      9. Use a cross-platform file transfer tool, and enter the MM910 floating IP address to download the configuration file to the PC in binary file transmission mode.
        • The configuration file of the converged switching plane on the MM910 is 34_1_1.cfg. The file name is different from that on the switch module.
        • The path for storing the configuration file is /common/flash/bladecfg/swiN.

          N is the CX311 slot number that ranges from 1 to 4, mapping to the logical slot numbers 1E, 2X, 3X, and 4E from left to right.

        WinSCP is used as the cross-platform file transfer tool. For details, see Transferring Files Using WinSCP.

        NOTE:

        Set the WinSCP transfer mode to the binary mode as follows: Press the shortcut keys Ctrl+Alt+P. The Preferences window is displayed. In the navigation tree on the left, choose Transfer, and click Binary and OK.

      10. Run the following command on the MM910 CLI to export the configuration file of the converged switching plane:

        root@SMM:/# swiconfexport swiN

        N is the slot number of a switch module. Its value ranges from 1 to 4, mapping to switch module slots 1E, 2X, 3X, and 4E from left to right.

        The following information is displayed with the configuration file name and directory.

        Succeed 
        Please check "/tmp/exchang/swiN/swiN.tar.gz"
      11. Use a cross-platform file transfer tool, and enter the MM910 floating IP address to download the configuration file shown in the command output to the PC in binary file transmission mode.

        WinSCP is used as the cross-platform file transfer tool. For details, see Transferring Files Using WinSCP.

        NOTE:

        Set the WinSCP transfer mode to the binary mode as follows: Press the shortcut keys Ctrl+Alt+P. The Preferences window is displayed. In the navigation tree on the left, choose Transfer, and click Binary and OK.

        After the configuration file is downloaded to the PC and decompressed, the converged switching plane configuration file is 34_1_1.cfg.

    • Save the FCoE gateway configuration file.
      1. Run the following commands to activate the current configuration data on the FCoE gateway CLI:

        FCoE_GW: admin> admin start

        FCoE_GW (admin): admin> config activate

        The command output is as follows:

        The currently active configuration will be activated.   Please confirm (y/n): [n]

        Enter Y to activate the current configuration.

      2. Save configuration data for the FCoE gateway to the configuration file.

        FCoE_GW (admin): admin> config backup

      3. On an SFTP tool, enter the FCoE gateway IP address (which can be queried by referring to Checking the FCoE Gateway), user name (images), and password (Huawei12#$) to open the FCoE gateway SFTP session, and copy the configuration file configdata to the PC. For details, see Transferring Files Using SFTP.

        The following is an example:

        > sftp images@ip_address  
        Connecting to ip_address  
              Password: Huawei12#$   
              sftp> get configdata   
              Fetching //configdata to configdata   
              sftp: received 105 KB in 0.03 seconds   
              sftp> quit 
        NOTE:

        It is recommended that you change the configuration file name on the workstation to the MX510 name and date, for example, config_mx510_06302015.

Translation
Download
Updated: 2018-09-20

Document ID: EDOC1000018097

Views: 61948

Downloads: 3389

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next