No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Enterprise
Worldwide
Huawei Global - English
Search
Support Documentation
CloudEngine 8800, 7800, 6800, and 5800 Series Switches Hardware Description (Versions earlier than V200R020C00)

This document provides an overall description of the CE5800&6800&7800&8800 series switches hardware that versions earlier than V200R020C00, helping you obtain detailed information about each chassis, power module, fan module, card, cable, and pluggable modules for ports.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
CE6880-48T4Q2CQ-EI

CE6880-48T4Q2CQ-EI

Version Mapping

Table 2-287 lists the mappings between the CE6880-48T4Q2CQ-EI and software versions.

Table 2-287 Version mapping

Device Series

Sub-series

Device Model

Short Name

Supported Version

CE6800

CE6880

CE6880-48T4Q2CQ-EI

CE6880EI

V200R002C50 to V200R019C10

NOTE:

This model is not supported in V200R005C20.

Appearance and Structure

The figures in this document are for reference only.

Figure 2-135 CE6880-48T4Q2CQ-EI

1

Power supply slot 1

Applicable power modules:

2

Power supply slot 2

Applicable power modules:

3

Fan slot 1

Applicable fan modules:

4

Fan slot 2

Applicable fan modules:

5

Console port

6

ETH management port (RJ45)

7
Barcode label
NOTE:

This label is drawable, and you can pull it outward to view the ESN barcode and MAC address of the switch.

8

USB port

9

Forty-eight 10GBASE-T Ethernet electrical ports

10

Two 40GE/100GE QSFP28 Ethernet optical ports

NOTE:
  • A QSFP28 Ethernet optical port can be split into four 10GE ports.

  • The default rate of a QSFP28 Ethernet optical port is 40 Gbit/s, and you can use the port mode 100ge command to change the port speed to 100 Gbit/s.

  • After the speed of 40GE1/0/1 is changed to 100 Gbit/s, ports 10GE1/0/45 and 10GE1/0/46 transition to Down (port unavailable) state. After the speed of 40GE1/0/2 is changed to 100 Gbit/s, ports 10GE1/0/47 and 10GE1/0/48 become unavailable.

Applicable modules and cables:

11

Four 40GE QSFP+ Ethernet optical ports

NOTE:

A 40GE QSFP+ port cannot be split into four 10GE ports.

Applicable modules and cables:

12

Three port-side mounting holes for mounting brackets

13

Four power-supply-side mounting holes for mounting brackets

14

Ground screw

Slot

  • Power supply slot

    The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI) have two power supply slots, in which power modules can be installed to provide power to the chassis. A chassis can have one or two power modules. Double power modules can provide higher reliability.

    The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI) support double power modules (1+1 backup).
    • When both power modules are working properly, they equally provide power for a chassis.
    • When one power module fails, the other one provides all power required for a chassis.
    All power modules are hot swappable.

  • Fan slot

    The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI, CE6863-48S6CQ, CE6881-48S6CQ, CE6820-48S6CQ, CE6863-48S6CQ-K, CE6881-48S6CQ-K, CE6881E-48S6CQ and CE6857-48S6CQ-EI) have two fan slots, in which fan modules can be installed to cool the chassis, ensuring efficient heat dissipation and system stability. A chassis must have two working fan modules to ensure normal operating.

    All fan modules are hot swappable.

Airflow

The cooling systems of the CloudEngine 8800, 7800, 6800, and 5800 series switches have front-to-back or back-to-front airflow depending on the airflow direction of the power modules and fan modules used. The airflow direction of the power modules and fan modules required on the CloudEngine 8800, 7800, 6800, and 5800 series switches depends on how the switches are installed in cabinets. Typically, cabinets in a data center have cold air flowing in from the front and hot air exhausted from the back. If CloudEngine 8800, 7800, 6800, and 5800 series switches are installed with the power supply side facing the front, you are advised to use fan modules and power modules with front-to-back airflow in the switches.
  • Front-to-back airflow: The power modules and fan modules using front-to-back airflow are marked or . Air flows into the chassis from the power supply side and flows out from the port side, as shown in Figure 2-136 (CE5800 as an example).
  • Back-to-front airflow: The power modules and fan modules using back-to-front airflow are marked or . Air flows into the chassis from the port side and flows out from the power supply side, as shown in Figure 2-137 (CE5800 as an example).

  • When the power module and fan module use forcible heat dissipation, they must use the same airflow method. For example, if the power module with back-to-front airflow is used, the fan module with back-to-front airflow must be used.

Figure 2-136 Front-to-back airflow (air flows out from the port side)
Figure 2-137 Back-to-front airflow (air flows in from the port side)

Indicators

The downlink service port indicators of the CE6880-48T4Q2CQ-EI are 10GE electrical port indicators, and other indicators are the same as those on the CE6880-24S4Q2CQ-EI. The CE6880-24S4Q2CQ-EI is used as an example here to describe the indicators.

Ports

10GBASE-T Ethernet Electrical Port

A 10GBASE-T Ethernet electrical port receives and sends service traffic at the rate of 100 Mbit/s, 1000 Mbit/s, or 10 Gbit/s. The port can work at the rate of 100 Mbit/s or 1000 Mbit/s through auto-sensing. 10GBASE-T Ethernet electrical ports must use Category 6A shielded Ethernet cables or higher Ethernet cables. Table 2-288 shows the attributes of a 10GBASE-T Ethernet electrical port.
Table 2-288 Attributes of a 10GBASE-T Ethernet electrical port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3an and IEEE802.3az

Applicable cable

Straight-through cable and crossover cable

Working mode

Supported rate: 100/1000 Mbit/s and 10 Gbit/s auto-sensing

Full-duplex

Maximum transmission distance

100 m

40GE QSFP+ Ethernet Optical Port

A 40GE QSFP+ Ethernet optical port receives and sends services at the rate of 40 Gbit/s. If a 40GE QSFP+ Ethernet optical port is split into four 10GE ports, it must use 1-to-4 QSFP+ optical modules and optical fibers or 1-to-4 QSFP+ cables. Table 2-289 describes the attributes of a 40GE QSFP+ Ethernet optical port.
Table 2-289 Attributes of a 40GE QSFP+ Ethernet optical port

Attribute

Description

Connector type

LC/MPO

Optical port attributes

Depending on the module or cable in use

Standards compliance

IEEE802.3ba

Working mode

Full-duplex

40GE/100GE QSFP28 Optical Port

Table 2-290 describes the attributes of a 40GE/100GE QSFP28 optical port.
Table 2-290 Attributes of a 40GE/100GE QSFP28 optical port

Attribute

Description

Connector type

Depending on the optical module

Optical attributes

Depending on the module or cable in use

Standards compliance

IEEE802.3ba

Working mode

Full-duplex

Console Port

The console port is connected to a console for onsite configuration. The port must use a console cable. Table 2-291 describes the attributes of the console port.
Table 2-291 Attributes of the console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s to 115200 bit/s

Default value: 9600 bit/s

ETH Management Port (RJ45)

The ETH management port (RJ45) of a switch is connected to the network port of a configuration terminal or network management workstation to set up the onsite or remote configuration environment. The ETH management port (RJ45) uses a Category 5 or higher category cable. Table 2-292 describes the attributes of the ETH management port (RJ45).
Table 2-292 Attributes of the ETH management port (RJ45)

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3ab

Working mode

Supported rate: 10/100/1000 Mbit/s auto-sensing

Full-duplex

Maximum transmission distance

100 m

USB Port

A USB flash drive can be connected to the USB port for log backup, system software backup and uploading, or USB-based deployment.

Specifications

Table 2-293 lists technical specifications of the CE6880-48T4Q2CQ-EI switch.

Table 2-293 Technical specifications

Item

Description

Physical specifications
  • Dimensions (W x D x H): 442.0 mm x 420.0 mm x 43.6 mm (17.4 in. x 16.5 in. x 1.72 in.)
  • Weight (with two power modules and two fan modules, calculated based on the heaviest model if multiple models are supported): 9.0 kg (19.84 lb)

Environment parameters

Temperature
  • Operating temperature: 0°C to 40°C (32°F to 104°F) at altitude of 0-1800 m (0-5906 ft.)
    NOTE:

    When the altitude is 1800-5000 m (5096-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

  • Storage temperature: -40°C to +70°C (-40°F to +158°F)

Relative humidity

5% RH to 95% RH, noncondensing

Altitude

< 5000 m (16404 ft.)

Noise (sound pressure, 27°C)
  • Back-to-front airflow: < 53 dBA
  • Front-to-back airflow: < 53 dBA

Power specifications

Power source type

AC

AC power input
  • Rated input voltage range: 100 V AC to 240 V AC, 50/60 Hz
  • Maximum input voltage range: 90 V AC to 290 V AC, 47 Hz to 63 Hz

DC power input
  • Rated voltage range: -48 V DC to -60 V DC
  • Maximum voltage range: -38.4 V DC to -72 V DC

High-voltage DC power input

Not supported

Rated input current
  • 600 W AC power (PAC-600WA series): 9 A (100 V AC to 240 V AC)
  • 600 W DC power (PDC600S12 series): 20A (-48 V DC to -60 V DC)

Chassis power consumption

Maximum power consumption

430 W

Typical power consumption

266 W (100% throughput, 3 m Ethernet cables on 48 ports and QSFP+ cables on 6 ports, double power modules)

Chassis heat dissipation

Maximum heat dissipation

1466 BTU/hr

Typical heat dissipation

906 BTU/hr (100% throughput, 3 m Ethernet cables on 48 ports and QSFP+ cables on 6 ports, double power modules)

Surge protection
Power module:
  • AC: 6 kV in common mode and 6 kV in differential mode

Heat dissipation

Heat dissipation mode

Air cooling

Airflow

Front-to-back or back-to-front, depending on the fan modules and power modules

Reliability

Power module backup

1+1 backup

Fan module backup

1+1 backup not supported

NOTE:

A CE6800 chassis uses two fan modules, with each fan module containing two fans. The four fans in the chassis work in 3+1 backup mode.

Hot swap

Supported by all power modules and fan modules

Mean time between failures (MTBF)

49.13 years

Mean time to repair (MTTR)

1.83 hours

Availability

0.99999575382

Technical specifications

Processor

1.5 GHz, eight-core

DRAM Memory

2 GB

NOR Flash

32 MB

NAND Flash

1 GB

Stack

Service port supporting the stack function

10GE electrical ports, 40GE optical ports, and 100GE optical ports

Certification
  • Safety standards compliance
  • EMC standards compliance
  • Environmental standards compliance

Ordering Information

Ordering information is subject to change without notice in the case of product upgrades. Ordering information provided in this manual is for reference only. To obtain latest ordering information, contact Huawei switch distributors or local Huawei representative office.

Table 2-294 provides the ordering information.

Table 2-294 Ordering information

Part Number

Part Model

Part Description

02350SRD

CE6880-48T4Q2CQ-EI

CE6880-48T4Q2CQ-EI Switch (48-Port 10G RJ45, 6-Port 40GE QSFP+ or 44-Port 10G RJ45, 4-Port 40GE QSFP+, 2-Port 100GE QSFP28, Without Fan and Power Module)

02350SRJ

CE6880-EI-F-B00

CE6880-48T4Q2CQ-EI Switch (48-Port 10G RJ45, 6-Port 40GE QSFP+ or 44-Port 10G RJ45, 4-Port 40GE QSFP+, 2-Port 100GE QSFP28, 2*AC Power Module, 2*FAN Box, Port-side Exhaust)

02350SRK

CE6880-EI-B-B00

CE6880-48T4Q2CQ-EI Switch (48-Port 10G RJ45, 6-Port 40GE QSFP+ or 44-Port 10G RJ45, 4-Port 40GE QSFP+, 2-Port 100GE QSFP28, 2*AC Power Module, 2*FAN Box, Port-side Intake)
Translation
简体中文
Download
Updated: 2021-06-01

Document ID: EDOC1000019246

Views: 1130513

Downloads: 12749

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Digital Signature File

Digital Signature Authentication Mode
Share
Previous Next

Copyright © 2023 Huawei Technologies Co., Ltd. All rights reserved.

You are going to visit :