No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Enterprise
Worldwide
Huawei Global - English
Search
Support Documentation
CloudEngine 8800, 7800, 6800, and 5800 Series Switches Hardware Description (Versions earlier than V200R020C00)

This document provides an overall description of the CE5800&6800&7800&8800 series switches hardware that versions earlier than V200R020C00, helping you obtain detailed information about each chassis, power module, fan module, card, cable, and pluggable modules for ports.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
CE5850-48T4S2Q-EI

CE5850-48T4S2Q-EI

Version Mapping

Table 2-16 lists the mappings between the CE5850-48T4S2Q-EI and software versions.

Table 2-16 Version mapping

Device Series

Sub-series

Device Model

Short Name

Supported Version

CE5800

CE5850

CE5850-48T4S2Q-EI

CE5850EI

V100R001C00 to V200R019C10

NOTE:

This model is not supported in V200R005C20.

Appearance and Structure

The figures in this document are for reference only.

Figure 2-8 CE5850-48T4S2Q-EI

1

Power supply slot 1

Applicable power modules:

2

Power supply slot 2

Applicable power modules:

3

Fan slot 1

Applicable fan modules:

4

Fan slot 2

Applicable fan modules:

5

Console port

6

ETH management port (RJ45)

7
Barcode label
NOTE:

This label is drawable, and you can pull it outward to view the ESN barcode and MAC address of the switch.

8

USB port

9

Forty-eight 10/100/1000BASE-T Ethernet electrical ports

10

Four 10GE SFP+ Ethernet optical ports

Applicable modules and cables:

11

Two 40GE QSFP+ Ethernet optical ports

NOTE:

A 40GE QSFP+ port cannot be split into four 10GE ports.

Applicable modules and cables:

12

Three port-side mounting holes for mounting brackets

13

Four power-supply-side mounting holes for mounting brackets

14

Ground screw

Slot

  • Power supply slot

    The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI) have two power supply slots, in which power modules can be installed to provide power to the chassis. A chassis can have one or two power modules. Double power modules can provide higher reliability.

    The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI) support double power modules (1+1 backup).
    • When both power modules are working properly, they equally provide power for a chassis.
    • When one power module fails, the other one provides all power required for a chassis.
    All power modules are hot swappable.

  • Fan slot

    The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI, CE6863-48S6CQ, CE6881-48S6CQ, CE6820-48S6CQ, CE6863-48S6CQ-K, CE6881-48S6CQ-K, CE6881E-48S6CQ and CE6857-48S6CQ-EI) have two fan slots, in which fan modules can be installed to cool the chassis, ensuring efficient heat dissipation and system stability. A chassis must have two working fan modules to ensure normal operating.

    All fan modules are hot swappable.

Airflow

The cooling systems of the CloudEngine 9800, 8800, 7800, 6800, and 5800 series switches have front-to-back or back-to-front airflow depending on the airflow direction of the power modules and fan modules used. The airflow direction of the power modules and fan modules required on the CloudEngine 9800, 8800, 7800, 6800, and 5800 series switches depends on how the switches are installed in cabinets. Typically, cabinets in a data center have cold air flowing in from the front and hot air exhausted from the back. If CloudEngine 9800, 8800, 7800, 6800, and 5800 series switches are installed with the power supply side facing the front, you are advised to use fan modules and power modules with front-to-back airflow in the switches.
  • Front-to-back airflow: The power modules and fan modules using front-to-back airflow are marked or . Air flows into the chassis from the power supply side and flows out from the port side, as shown in Figure 2-9 (CE5800 as an example).
  • Back-to-front airflow: The power modules and fan modules using back-to-front airflow are marked or . Air flows into the chassis from the port side and flows out from the power supply side, as shown in Figure 2-10 (CE5800 as an example).

  • When the power module and fan module use forcible heat dissipation, they must use the same airflow method. For example, if the power module with back-to-front airflow is used, the fan module with back-to-front airflow must be used.

  • When the fanless 150 W AC power module is used, the fan module with either of the airflow methods can be used.

Figure 2-9 Front-to-back airflow (air flows out from the port side)
Figure 2-10 Back-to-front airflow (air flows into from the port side)

Indicators

The CE5850-48T4S2Q-EI has no 40GE Breakout indicators 1/2/3/4, and other indicators are the same as those on the CE5850-48T4S2Q-HI. The CE5850-48T4S2Q-HI is used as an example here to describe the indicators.

Ports

10/100/1000BASE-T Ethernet Electrical Port

A 10/100/1000BASE-T Ethernet electrical port receives and sends services at a rate of 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s. A 10/100/1000BASE-T Ethernet electrical port uses a Category 5 or higher category cable. Table 2-17 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.
Table 2-17 Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3ab

Applicable cable

Straight-through cable and crossover cable

Working mode

Supported rate: 10/100/1000 Mbit/s auto-sensing

Full-duplex

Maximum transmission distance

100 m

10GE SFP+ Ethernet Optical Port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1 Gbit/s, and can receive and send services at a rate of 1000 Mbit/s or 10 Gbit/s. Table 2-18 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 2-18 Attributes of a 10GE SFP+ Ethernet optical port

Attribute

Description

Connector type

LC

Optical attributes

Depending on the module or cable in use

Standards compliance

IEEE802.3ae

Working mode

Supported rate: 1000 Mbit/s and 10 Gbit/s auto-sensing

Full-duplex
A 5 m SFP+ high-speed cable cannot be used to connect 10GE optical ports between the CE5850EI (running a version prior to V100R005C10) and CE5855EI switches. To connect the 10GE optical ports of the two switches, use any of the following methods:
  • Use a 1 m, 3 m, 7 m, or 10 m SFP+ high-speed cable.
  • Use an active optical cable (AOC) or optical modules and optical fibers.
  • Upgrade the system software of the CE5850EI switch to V100R005C10 or a later version.

40GE QSFP+ Ethernet Optical Port

A 40GE QSFP+ Ethernet optical port receives and sends services at the rate of 40 Gbit/s. If a 40GE QSFP+ Ethernet optical port is split into four 10GE ports, it must use 1-to-4 QSFP+ optical modules and optical fibers or 1-to-4 QSFP+ cables. Table 2-19 describes the attributes of a 40GE QSFP+ Ethernet optical port.
Table 2-19 Attributes of a 40GE QSFP+ Ethernet optical port

Attribute

Description

Connector type

LC/MPO

Optical port attributes

Depending on the module or cable in use

Standards compliance

IEEE802.3ba

Working mode

Full-duplex
A 5 m 1-to-4 QSFP+ high-speed cable cannot be used to connect a 40GE optical port (split into four 10GE ports) and 10GE optical ports between the CE5850EI (running a version prior to V100R005C10) and CE5855EI switches. To connect the 10GE and 40GE optical ports of the two switches, use any of the following methods:
  • Use a 1 m or 3 m 1-to-4 QSFP+ high-speed cable.
  • Use optical modules and optical fibers.
  • Upgrade the system software of the CE5850EI switch to V100R005C10 or a later version.

Console Port

The console port is connected to a console for onsite configuration. The port must use a console cable. Table 2-20 describes the attributes of the console port.
Table 2-20 Attributes of the console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s to 115200 bit/s

Default value: 9600 bit/s

ETH Management Port (RJ45)

The ETH management port (RJ45) of a switch is connected to the network port of a configuration terminal or network management workstation to set up the onsite or remote configuration environment. The ETH management port (RJ45) uses a Category 5 or higher category cable. Table 2-21 describes the attributes of the ETH management port (RJ45).
Table 2-21 Attributes of the ETH management port (RJ45)

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3ab

Working mode

Supported rate: 10/100/1000 Mbit/s auto-sensing

Full-duplex

Maximum transmission distance

100 m

USB Port

A USB flash drive can be connected to the USB port for log backup, system software backup and uploading, or USB-based deployment.

Specifications

Table 2-22 lists technical specifications of the CE5850-48T4S2Q-EI switch.

Table 2-22 Technical specifications

Item

Description

Physical specifications
  • Dimensions (W x D x H): 442.0 mm x 420.0 mm x 43.6 mm (17.4 in. x 16.5 in. x 1.72 in.)
  • Weight (with two power modules and two fan modules, calculated based on the heaviest model if multiple models are supported): 8.85 kg (19.51 lb)

Environment parameters

Temperature
  • Operating temperature: 0°C to 40°C (32°F to 104°F) at altitude of 0-1800 m (0-5906 ft.)
    NOTE:

    When the altitude is 1800-5000 m (5096-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

  • Storage temperature: -40°C to +70°C (-40°F to +158°F)

Relative humidity

5% RH to 95% RH, noncondensing

Altitude

< 5000 m (16404 ft.)

Noise (sound pressure, 27°C)
  • Back-to-front airflow: < 45 dBA
  • Front-to-back airflow: < 45 dBA

Power specifications

Power source type

AC/DC

AC power input
  • Rated input voltage range: 100 V AC to 240 V AC, 50/60 Hz
  • Maximum input voltage range: 90 V AC to 290 V AC, 47 Hz to 63 Hz

DC power input
  • Rated voltage range: -48 V DC to -60 V DC
  • Maximum voltage range: -38.4 V DC to -72 V DC

High-voltage DC power input

Not supported

Rated input current
  • 150 W AC power (PAC-150WA): 2.5 A (100 V AC to 240 V AC)
  • 350 W DC power (PDC-350WA series): 11 A (-48 V DC to -60 V DC)

Chassis power consumption

Maximum power consumption

133 W

Typical power consumption

103 W (100% throughput, 3 m Ethernet cables on 48 ports and SFP+ cables on 4 ports and QSFP+ cables on 2 ports, double power modules)

Chassis heat dissipation

Maximum heat dissipation

454 BTU/hr

Typical heat dissipation

351 BTU/hr (100% throughput, 3 m Ethernet cables on 48 ports and SFP+ cables on 4 ports and QSFP+ cables on 2 ports, double power modules)

Surge protection

Ethernet electrical ports: 2 kV in common mode

Power module:
  • AC: 6 kV in common mode and 6 kV in differential mode
  • DC: 4 kV in common mode and 2 kV in differential mode

Heat dissipation

Heat dissipation mode

Air cooling

Airflow

Front-to-back or back-to-front, depending on the fan modules and power modules

Reliability and availability

Power module backup

1+1 backup

Fan module backup

1+1 backup

Hot swap

Supported by all power modules and fan modules

Mean time between failures (MTBF)

53.27 years

Mean time to repair (MTTR)

2.0 hours

Availability

0.9999947257

Technical specifications

Processor

1.2 GHz, quad-core

DRAM Memory

2 GB

NOR Flash

8 MB

NAND Flash

1 GB

Stack

Service port supporting the stack function

10GE optical ports and 40GE optical ports

Certification
  • Safety standards compliance
  • EMC standards compliance
  • Environmental standards compliance

Ordering Information

Ordering information is subject to change without notice in the case of product upgrades. Ordering information provided in this manual is for reference only. To obtain latest ordering information, contact Huawei switch distributors or local Huawei representative office.

Table 2-23 provides the ordering information.

Table 2-23 Ordering information

Part Number

Part Model

Part Description

02355272

CE5850-48T4S2Q-EI

CE5850-48T4S2Q-EI Switch (48-Port GE RJ45, 4-Port 10GE SFP+, 2-Port 40GE QSFP+, Without Fan Box and Power Module)

02350EXX

CE5850-48T4S2Q-EI-F

CE5850-48T4S2Q-EI Switch (48-Port GE RJ45, 4-Port 10G SFP+, 2-Port 40G QSFP+, 2*FAN Box, Port-side Exhaust, Without Power Module)

02350EXY

CE5850-48T4S2Q-EI-B

CE5850-48T4S2Q-EI Switch (48-Port GE RJ45, 4-Port 10G SFP+, 2-Port 40G QSFP+, 2*FAN Box, Port-side Intake, Without Power Module)

02359104

CE5850-EI-B00

CE5850-48T4S2Q-EI Switch (2*150W AC Power Module, 2*FAN Box, Port-side Exhaust)

02350FCK

CE5850-EI-B-B00

CE5850-48T4S2Q-EI Switch (2*150W Power Module, 2*FAN Box, Port-side Intake)
Translation
简体中文
Download
Updated: 2021-06-01

Document ID: EDOC1000019246

Views: 1085445

Downloads: 12367

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Digital Signature File

Digital Signature Authentication Mode
Share
Previous Next

Copyright © 2023 Huawei Technologies Co., Ltd. All rights reserved.

You are going to visit :