No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Enterprise
Worldwide
Huawei Global - English
Search
Support Documentation
CloudEngine 8800, 7800, 6800, and 5800 Series Switches Hardware Description (Versions earlier than V200R020C00)

This document provides an overall description of the CE5800&6800&7800&8800 series switches hardware that versions earlier than V200R020C00, helping you obtain detailed information about each chassis, power module, fan module, card, cable, and pluggable modules for ports.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
CE6881-48S6CQ

CE6881-48S6CQ

Version Mapping

Table 2-295 lists the mappings between the CE6881-48S6CQ and software versions.

Table 2-295 Version mapping

Device Series

Sub-series

Device Model

Short Name

Supported Version

CE6800

CE6881

CE6881-48S6CQ

CE6881

V200R005C20 and later

Appearance and Structure

The figures in this document are for reference only.

Figure 2-138 CE6881-48S6CQ

1

Ground screw

2
Equipment serial number (ESN)
NOTE:

You can scan the code to view the ESN and MAC address of the switch.

3

Console port

4

ETH management port (RJ45)

5

USB port

6

Fan slot 1

Applicable fan modules:

7

Fan slot 2

Applicable fan modules:

8

Fan slot 3

Applicable fan modules:

9

Fan slot 4

Applicable fan modules:

10

Power supply slot 1

Applicable power modules:

11

Power supply slot 2

Applicable power modules:

12

Forty-eight 10GE SFP+ Ethernet optical ports

Applicable modules and cables:

NOTE:

GE media cannot be installed on 10GE ports numbered from 13 to 16 and from 25 to 28 on the CE6881 in V200R005C20. If GE medium is installed on such ports, the ports will be set to the Error-Down state. In V200R019C10 and later versions, after GE medium is installed on 10GE ports numbered from 13 to 16 and from 25 to 28, you need to run the speed 1000 command to change the port rate to 1000 Mbit/s so that the ports can go Up. The rate of such ports numbered from 13 to 16 or from 25 to 28 will be changed simultaneously. For example, if you run the speed 1000 command on port 13 that has a GE medium installed, the rate of ports 14, 15, and 16 will be changed simultaneously.

13

Six 40GE/100GE QSFP28 Ethernet optical ports

Applicable modules and cables:
  • QSFP+ to QSFP+ AOC cable
  • QSFP+ to QSFP+ high-speed cable (The cable can only be used as a stack cable or be used to connect peer-link interfaces in an M-LAG.)
  • QSFP28 to QSFP28 AOC cable
  • QSFP28 to QSFP28 high-speed cable (The cable can only be used as a stack cable or be used to connect peer-link interfaces in an M-LAG.)
    NOTE:

    When a QSFP28 high-speed cable is installed on a 100GE port that works at the rate of 100 Gbit/s, the port supports only the 1 m QSFP28 high-speed cable.

    When a QSFP28 high-speed cable is installed on a 100GE port and the speed 40000 command is run to set the rate to 40 Gbit/s, the port supports 1 m, 3 m, and 5 m QSFP28 high-speed cables.

14

Three port-side mounting holes for mounting brackets

15

Two middle mounting holes for mounting brackets

16

Equipotential bonding

Ground screws for a ground cable with a two-hole OT terminal

17

Four power-supply-side mounting holes for mounting brackets

-

-

Slot Description

Power Slots

Each of the CloudEngine 6800 series switches has two power module slots and supports pluggable power modules. A chassis can use one or two power modules. In particular, dual power modules provide higher reliability.

The CloudEngine 6800 series switches support 1+1 backup of power modules.
  • When both power modules are working properly, each of them provides half of the power required for the chassis.
  • When one power module fails, the other one provides all power required for the chassis.
All power modules of the devices are hot swappable.

Fan Slots

Each of the CloudEngine 6800 series switches has four fan slots in which fan modules can be installed to cool the chassis, ensuring efficient heat dissipation and system stability.

It is recommended that four fan modules be properly installed on a switch to ensure normal switch operating. The device supports four pluggable fan modules that work in hot standby mode. The system can operate properly for a short time after a single fan module fails. You are advised to replace the faulty fan module immediately.

All fan modules are hot swappable.

Heat Dissipation System

The cooling system of the CloudEngine 6800 series switches uses front-to-back or back-to-front airflow depending on the airflow direction of the power modules and fan modules used.

  • Front-to-back airflow: Power modules and fan modules with front-to-back airflow are identified by . Air flows into the chassis from the power supply side and is exhausted from the port side, as shown in Figure 2-139 (using a CE6863 chassis as an example).
  • Back-to-front airflow: Power modules and fan modules with back-to-front airflow are identified by . Air flows into the chassis from the port side and is exhausted from the power supply side, as shown in Figure 2-140 (using a CE6863 chassis as an example).
Figure 2-139 Front-to-back airflow for port-side exhaust
Figure 2-140 Back-to-front airflow for port-side intake
The airflow direction of the power modules and fan modules required on the CloudEngine 6800 series switches depends on how the device is installed in a cabinet. Typically, cabinets in a data center have cold air flowing in from the front and hot air exhausted from the back. If a switch is installed with the power supply side facing the front and the port side facing the back, the switch needs to adopt fan modules and power modules with front-to-back airflow.

Power modules and fan modules using forced air cooling on a switch must have the same airflow direction. If a switch adopts power modules with back-to-front airflow, the switch must use fan modules with back-to-front airflow as well.

Indicators

The downlink service port indicator on the CE6881-48S6CQ is the 10GE optical port indicator. The status and status meanings of other indicators are the same as those of the CE6863-48S6CQ. The CE6863-48S6CQ is used as an example here to describe the indicators.

Ports

10GE SFP+ Ethernet Optical Port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1 Gbit/s, and can receive and send services at a rate of 1000 Mbit/s or 10 Gbit/s. Table 2-296 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 2-296 Attributes of a 10GE SFP+ Ethernet optical port

Attribute

Description

Connector type

LC

Optical attributes

Depending on the module or cable in use

Standards compliance

IEEE802.3ae

Working mode

Supported rate: 1000 Mbit/s and 10 Gbit/s auto-sensing

Full-duplex

40GE/100GE QSFP28 Optical Port

Table 2-297 describes the attributes of a 40GE/100GE QSFP28 optical port.
Table 2-297 Attributes of a 40GE/100GE QSFP28 optical port

Attribute

Description

Connector type

Depending on the optical module

Optical attributes

Depending on the module or cable in use

Standards compliance

IEEE802.3ba

Working mode

Full-duplex

Console Port

The console port is connected to a console for onsite configuration. The port must use a console cable. Table 2-298 describes the attributes of the console port.
Table 2-298 Attributes of the console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s to 115200 bit/s

Default value: 9600 bit/s

ETH Management Port (RJ45)

The ETH management port (RJ45) of a switch is connected to the network port of a configuration terminal or network management workstation to set up the onsite or remote configuration environment. The ETH management port (RJ45) uses a Category 5 or higher category cable. Table 2-299 describes the attributes of the ETH management port (RJ45).
Table 2-299 Attributes of the ETH management port (RJ45)

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3ab

Working mode

Supported rate: 10/100/1000 Mbit/s auto-sensing

Full-duplex

Maximum transmission distance

100 m

USB Port

A USB flash drive can be connected to the USB port for log backup, system software backup and uploading, or USB-based deployment.

Specifications

Table 2-300 lists technical specifications of the CE6881-48S6CQ switch.

Table 2-300 Technical specifications

Item

Description

Physical specifications
  • Dimensions (H x W x D)
    • Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.)
    • Maximum dimensions (the depth is the distance from ports on the front panel to the handle on the rear panel): 43.6 mm x 442.0 mm x 446.1 mm (1.72 in. x 17.4 in. x 17.6 in.)
  • Weight (with two AC power modules and four fan modules, calculated based on the heaviest model if multiple models are supported): 7.8 kg (17.20 lb)

Environment parameters

Temperature
  • Operating temperature: 0°C to 40°C (32°F to 104°F) at altitude of 0-1800 m (0-5906 ft.)
    NOTE:

    When the altitude is 1800-5000 m (5096-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

  • Storage temperature: -40°C to +70°C (-40°F to +158°F)

Relative humidity

5% RH to 95% RH, noncondensing

Altitude

< 5000 m (16404 ft.)

Noise (sound pressure, 27°C)
  • Back-to-front airflow: < 57 dBA
  • Front-to-back airflow: < 58 dBA

Power specifications

Power source type

AC/DC/HVDC

AC power input
  • Rated input voltage range: 100 V AC to 240 V AC, 50/60 Hz
  • Maximum input voltage range: 90 V AC to 290 V AC, 47 Hz to 63 Hz

DC power input
  • Rated voltage range: -48 V DC to -60 V DC
  • Maximum voltage range: -38.4 V DC to -72 V DC

High-voltage DC power input
  • 600 W AC&240 V DC power module (PAC600S12 series):
    • Rated voltage range: 240 V DC
    • Maximum voltage range: 190 V DC to 290 V DC
  • 1200 W high-voltage DC power module (PHD1K2S12 series):
    • Rated voltage range: 240 V DC to 380V DC
    • Maximum voltage range: 190 V DC to 400 V DC

Rated input current
  • 600 W AC&240 V DC power module (PAC600S12 series):
    • 8 A (100 V AC to 240 V AC)
    • 4 A (240V DC)
  • 1000 W DC power module (PDC1000S12 series): 30 A (-48 V DC to -60 V DC)
  • 1200 W high-voltage DC power module (PHD1K2S12 series): 8 A

Chassis power consumption

Maximum power consumption

349 W

Typical power consumption
  • 194 W (100% throughput, SFP+ high-speed cables on 48 ports and QSFP28 high-speed cables on 6 ports, double power modules)
  • 240 W (100% throughput, short-distance optical modules on all optical ports, double power modules)

Chassis heat dissipation

Maximum heat dissipation

1191 BTU/hr

Typical heat dissipation
  • 662 BTU/hr (100% throughput, SFP+ high-speed cables on 48 ports and QSFP28 high-speed cables on 6 ports, double power modules)
  • 819 BTU/hr (100% throughput, short-distance optical modules on all optical ports, double power modules)

Surge protection
Power module:
  • AC: 6 kV in common mode and 6 kV in differential mode
  • DC: 4 kV in common mode and 2 kV in differential mode
  • HVDC: 4 kV in common mode and 2 kV in differential mode

Heat dissipation

Heat dissipation mode

Air cooling

Airflow

Front-to-back or back-to-front, depending on the fan modules and power modules

Reliability and availability

Power module backup

1+1 backup

Fan module backup

The device supports four pluggable fan modules that work in hot standby mode. The system can operate properly for a short time after a single fan module fails. You are advised to replace the faulty fan module immediately.

Hot swap

Supported by all power modules and fan modules

Mean time between failures (MTBF)

45.9 years

Mean time to repair (MTTR)

1.57 hours

Availability

0.9999960856

Technical specifications

Processor

1.4 GHz, four-core

DRAM memory

4 GB

NOR Flash

64 MB

NAND Flash

4 GB

Stack

Service port supporting the stacking function

10GE optical ports and 100GE optical ports

Certification
  • Safety standards compliance
  • EMC standards compliance
  • Environmental standards compliance

Ordering Information

Ordering information is subject to change without notice in the case of product upgrades. Ordering information provided in this manual is for reference only. To obtain latest ordering information, contact Huawei switch distributors or local Huawei representative office.

Table 2-301 provides the ordering information.

Table 2-301 Ordering information

Part Number

Part Model

Part Description

02352QGF

CE6881-48S6CQ

CE6881-48S6CQ switch (48*10GE SFP+, 6*100GE QSFP28, without fan and power modules)

02352QGG

CE6881-48S6CQ-B

CE6881-48S6CQ switch (48*10GE SFP+, 6*100GE QSFP28, 2*AC power modules, 4*fan modules, port-side intake)

02352QGH

CE6881-48S6CQ-F

CE6881-48S6CQ switch (48*10GE SFP+, 6*100GE QSFP28, 2*AC power modules, 4*fan modules, port-side exhaust)
Translation
简体中文
Download
Updated: 2021-06-01

Document ID: EDOC1000019246

Views: 1123555

Downloads: 12693

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Digital Signature File

Digital Signature Authentication Mode
Share
Previous Next

Copyright © 2023 Huawei Technologies Co., Ltd. All rights reserved.

You are going to visit :