CE5880-48T6Q-EI
Version Mapping
Table 2-50 lists the mappings between the CE5880-48T6Q-EI and software versions.
Appearance and Structure
The figures in this document are for reference only.
1 |
Power supply slot 1 Applicable power modules:
|
2 |
Power supply slot 2 Applicable power modules:
|
3 |
Fan slot 1 Applicable fan modules:
|
4 |
Fan slot 2 Applicable fan modules:
|
5 |
Console port |
6 |
ETH management port (RJ45) |
7 |
Barcode label
NOTE:
This label is drawable, and you can pull it outward to view the ESN barcode and MAC address of the switch. |
8 |
USB port |
9 |
Forty-four 100/1000BASE-T Ethernet electrical ports |
10 |
Four 10GBASE-T Ethernet electrical ports |
11 |
Six 40GE QSFP+ Ethernet optical ports NOTE:
A 40GE interface with the number of 1 to 2 is configured to be split into four 10GE interfaces. The other 40GE interfaces cannot be split into four 10GE interfaces. Applicable modules and cables:
|
12 |
Three port-side mounting holes for mounting brackets |
13 |
Four power-supply-side mounting holes for mounting brackets |
14 |
Ground screw |
Slot
Power supply slot
The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI) have two power supply slots, in which power modules can be installed to provide power to the chassis. A chassis can have one or two power modules. Double power modules can provide higher reliability.
The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI) support double power modules (1+1 backup).- When both power modules are working properly, they equally provide power for a chassis.
- When one power module fails, the other one provides all power required for a chassis.
Fan slot
The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI, CE6863-48S6CQ, CE6881-48S6CQ, CE6820-48S6CQ, CE6863-48S6CQ-K, CE6881-48S6CQ-K, CE6881E-48S6CQ and CE6857-48S6CQ-EI) have two fan slots, in which fan modules can be installed to cool the chassis, ensuring efficient heat dissipation and system stability. A chassis must have two working fan modules to ensure normal operating.
All fan modules are hot swappable.
Airflow
- Front-to-back airflow: The power modules and fan modules using front-to-back airflow are marked
or
. Air flows into the chassis from the power supply side and flows out from the port side, as shown in Figure 2-23 (CE5800 as an example).
- Back-to-front airflow: The power modules and fan modules using back-to-front airflow are marked
or
. Air flows into the chassis from the port side and flows out from the power supply side, as shown in Figure 2-24 (CE5800 as an example).
When the power module and fan module use forcible heat dissipation, they must use the same airflow method. For example, if the power module with back-to-front airflow is used, the fan module with back-to-front airflow must be used.
- Front-to-back airflow: The power modules and fan modules using front-to-back airflow are marked
or
. Air flows into the chassis from the power supply side and flows out from the port side, as shown in Figure 2-25 (CE5800 as an example).
- Back-to-front airflow: The power modules and fan modules using back-to-front airflow are marked
or
. Air flows into the chassis from the port side and flows out from the power supply side, as shown in Figure 2-26 (CE5800 as an example).
When the power module and fan module use forcible heat dissipation, they must use the same airflow method. For example, if the power module with back-to-front airflow is used, the fan module with back-to-front airflow must be used.
Indicators
The downlink service port indicators of the CE5880-48T6Q-EI are GE and 10GE electrical port indicators. There is no 40GE/100GE optical port. Other indicators are the same as those on the CE6880-24S4Q2CQ-EI. The CE6880-24S4Q2CQ-EI is used as an example here to describe the indicators.
Ports
100/1000BASE-T Ethernet Electrical Port
The GE electrical interface on the CE5880-48T6Q-EI could not set the auto-negotiation rate of an Ethernet electrical interface to 10 Mbit/s.
Attribute |
Description |
---|---|
Connector type |
RJ45 |
Standards compliance |
IEEE802.3ab |
Applicable cable |
Straight-through cable and crossover cable |
Working mode |
Supported rate: 10/100/1000 Mbit/s auto-sensing Full-duplex |
Maximum transmission distance |
100 m |
Attribute |
Description |
---|---|
Connector |
RJ45 |
Standards compliance |
IEEE802.3ab |
Applicable cable |
Straight-through cable and crossover cable |
Working mode |
Supported rate: 10/100/1000 Mbit/s auto-sensing Full-duplex |
Maximum transmission distance |
100 m |
10GBASE-T Ethernet Electrical Port
Attribute |
Description |
---|---|
Connector type |
RJ45 |
Standards compliance |
IEEE802.3an and IEEE802.3az |
Applicable cable |
Straight-through cable and crossover cable |
Working mode |
Supported rate: 100/1000 Mbit/s and 10 Gbit/s auto-sensing Full-duplex |
Maximum transmission distance |
100 m |
Attribute |
Description |
---|---|
Connector |
RJ45 |
Standards compliance |
IEEE802.3an and IEEE802.3az |
Applicable cable |
Straight-through cable and crossover cable |
Working mode |
Supported rate: 100/1000 Mbit/s and 10 Gbit/s auto-sensing Full-duplex |
Maximum transmission distance |
100 m |
40GE QSFP+ Ethernet Optical Port
Attribute |
Description |
---|---|
Connector |
LC/MPO |
Optical attributes |
Depending on the module or cable used |
Standards compliance |
IEEE802.3ba |
Working mode |
Full-duplex |
Console Port
Attribute |
Description |
---|---|
Connector |
RJ45 |
Standards compliance |
RS232 |
Working mode |
Duplex Universal Asynchronous Receiver/Transmitter (UART) |
Baud rate |
9600 bit/s - 115200 bit/s Default value: 9600 bit/s |
ETH Management Port (RJ45)
Attribute |
Description |
---|---|
Connector |
RJ45 |
Standards compliance |
IEEE802.3ab |
Working mode |
Supported rate: 10/100/1000 Mbit/s auto-sensing Full-duplex |
Maximum transmission distance |
100 m |
USB Port
A USB flash drive can be connected to the USB port for log backup, system software backup and uploading, or USB-based deployment.
Specifications
Table 2-61 lists technical specifications of the CE5880-48T6Q-EI switch.
Item |
Description |
|
---|---|---|
Physical specifications |
|
|
Environment parameters |
Temperature |
|
Relative humidity |
5% RH to 95% RH, noncondensing |
|
Altitude |
< 5000 m (16404 ft.) |
|
Noise (sound pressure, 27°C) |
|
|
Power specifications |
Power source type |
AC |
AC power input |
|
|
DC power input |
|
|
High-voltage DC power input |
Not supported |
|
Rated input current |
|
|
Chassis power consumption |
Maximum power consumption |
244 W |
Typical power consumption |
211 W (100% throughput, 3 m Ethernet cables on 48 ports and QSFP+ cables on 6 ports, double power modules) 222 W (100% throughput, 3 m Ethernet cables on 48 ports and QSFP+ short-distance optical modules on 6 ports, double power modules) |
|
Chassis heat dissipation |
Maximum heat dissipation |
833 BTU/hr |
Typical heat dissipation |
720 BTU/hr (100% throughput, 3 m Ethernet cables on 48 ports and QSFP+ cables on 6 ports, double power modules) 757 BTU/hr (100% throughput, 3 m Ethernet cables on 48 ports and QSFP+ short-distance optical modules on 6 ports, double power modules) |
|
Surge protection |
Power module:
|
|
Heat dissipation |
Heat dissipation mode |
Air cooling |
Airflow |
Front-to-back or back-to-front, depending on the fan modules and power modules |
|
Reliability |
Power module backup |
1+1 backup |
Fan module backup |
1+1 backup not supported NOTE:
The CE5880-48T6Q-EI chassis uses two fan modules, with each fan module containing two fans. The four fans in the chassis work in 3+1 backup mode. |
|
Hot swap |
Supported by all power modules and fan modules |
|
Mean time between failures (MTBF) |
49.14 years |
|
Mean time to repair (MTTR) |
1.71 hours |
|
Availability |
0.99999575382 |
|
Technical specifications |
Processor |
1.5 GHz, eight-core |
DRAM Memory |
2 GB |
|
NOR Flash |
32 MB |
|
NAND Flash |
1 GB |
|
Stack |
Service port supporting the stack function |
GE electrical ports, 10GE electrical ports, and 40GE optical ports |
Certification |
|
Ordering Information
Ordering information is subject to change without notice in the case of product upgrades. Ordering information provided in this manual is for reference only. To obtain latest ordering information, contact Huawei switch distributors or local Huawei representative office.
Table 2-62 provides the ordering information.
Part Number |
Part Model |
Part Description |
---|---|---|
02352AXG |
CE5880-48T6Q-EI |
CE5880-48T6Q-EI Switch (44Port G RJ45, 4-Port 10G RJ45, 6-Port 40GE QSFP+, Without Fan and Power Module) |
02352AXK |
CE5880-EI-F-B00 |
CE5880-48T4Q2CQ-EI Switch (44Port G RJ45, 4-Port 10G RJ45, 6-Port 40GE QSFP+, 2*AC Power Module, 2*FAN Box, Port-side Exhaust) |
02352AXL |
CE5880-EI-B-B00 |
CE5880-48T4Q2CQ-EI Switch (44Port G RJ45, 4-Port 10G RJ45, 6-Port 40GE QSFP+, 2*AC Power Module, 2*FAN Box, Port-side Intake) |