CE8850-32CQ-EI
Version Mapping
Table 2-349 lists the mappings between the CE8850-32CQ-EI and software versions.
Appearance and Structure
The figures in this document are for reference only.
1 |
Power supply slot 1 Applicable power modules:
|
2 |
Power supply slot 2 Applicable power modules:
|
3 |
Fan slot 1 Applicable fan modules:
|
4 |
Fan slot 2 Applicable fan modules:
|
5 |
Console port |
6 |
ETH management port (RJ45) |
7 |
Barcode label
NOTE:
This label is drawable, and you can pull it outward to view the ESN barcode and MAC address of the switch. |
8 |
USB port |
9 |
Thirty-two 40GE/100GE QSFP28 Ethernet optical ports NOTE:
A QSFP28 Ethernet optical port can be split into four 10GE or 25GE ports. Applicable modules and cables:
|
10 |
Two 10GE SFP+ Ethernet optical ports Applicable modules and cables:
|
11 |
Three port-side mounting holes for mounting brackets |
12 |
Four power-supply-side mounting holes for mounting brackets |
13 |
Ground screw |
- |
- |
Slot
Power supply slot
The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI) have two power supply slots, in which power modules can be installed to provide power to the chassis. A chassis can have one or two power modules. Double power modules can provide higher reliability.
The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI) support double power modules (1+1 backup).- When both power modules are working properly, they equally provide power for a chassis.
- When one power module fails, the other one provides all power required for a chassis.
Fan slot
The CloudEngine 8800, 7800, 6800, and 5800 series switches (except the CE8850-64CQ-EI, CE6863-48S6CQ, CE6881-48S6CQ, CE6820-48S6CQ, CE6863-48S6CQ-K, CE6881-48S6CQ-K, CE6881E-48S6CQ and CE6857-48S6CQ-EI) have two fan slots, in which fan modules can be installed to cool the chassis, ensuring efficient heat dissipation and system stability. A chassis must have two working fan modules to ensure normal operating.
All fan modules are hot swappable.
Airflow
- Front-to-back airflow: The power modules and fan modules using front-to-back airflow are marked
or
. Air flows into the chassis from the power supply side and flows out from the port side, as shown in Figure 2-169 (CE5800 as an example).
- Back-to-front airflow: The power modules and fan modules using back-to-front airflow are marked
or
. Air flows into the chassis from the port side and flows out from the power supply side, as shown in Figure 2-110 (CE5800 as an example).
When the power module and fan module use forcible heat dissipation, they must use the same airflow method. For example, if the power module with back-to-front airflow is used, the fan module with back-to-front airflow must be used.
Indicators
Indicators on the CE8850-32CQ-EI are the same as those on the CE7850-32Q-EI. CE7850-32Q-EI is used as an example.
No. |
Indicator |
Name |
Color |
Status |
Description |
---|---|---|---|---|---|
1 |
SYS |
System status indicator |
Green |
Off |
The system is not running. |
Fast blinking |
The system is starting. |
||||
Slow blinking |
The system is running normally. |
||||
Red |
Steady on |
|
|||
2 |
MST |
Stack master/slave indicator NOTE:
In V200R003C00 and later versions, you can use the dfs-master led enable command to enable the stack master/slave indicator to display the DFS group master and backup status. After the stack master/slave indicator is enabled to display the DFS group master and backup status, the stack master/slave indicator on the DFS master device is steady on and that on the DFS backup device is off. |
Green |
Off |
The switch is not a stack master. |
Steady on |
The switch is a stack master or standalone switch. |
||||
Yellow |
Steady on |
A master election error or another type of error has occurred in the stack.
NOTE:
This indicator state is not supported in V100R005C00 and later versions. |
|||
3 |
STAT |
STAT mode indicator |
Green |
Off |
The STAT mode is not selected. |
Steady on |
The STAT mode (default mode) is selected, and service port indicators show the link connection states and link activity on ports. |
||||
4 |
SPEED |
SPEED mode indicator |
Green |
Off |
The SPEED mode is not selected. |
Steady on |
The SPEED mode is selected, and service port indicators show the speed of each port. |
||||
5 |
STACK |
STACK mode indicator |
Green |
Off |
The STACK mode is not selected. |
Steady on |
The STACK mode is selected, and service port indicators show the stack member ID of the local switch. |
||||
6 |
MODE/ID |
Mode switch button and ID indicator NOTE:
The mode switch button on the rear panel is integrated with the ID indicator. There is only an ID indicator and no mode switch button on the front panel. |
Mode switch button |
- |
If you do not press the MODE button within 45 seconds, the service port indicators restore to the default mode. In this case, the STAT indicator is steady green, the SPEED and STACK indicators are off. |
ID indicator: blue |
Off |
The ID indicator is not used (default state). |
|||
Steady on |
The indicator identifies the switch to maintain. The ID indicator can be turned on or off remotely to help field engineers find the switch to maintain. |
||||
7 |
- |
Service port indicator (40GE optical port) NOTE:
Arrowheads show the positions of ports. A down arrowhead indicates a port at the bottom, and an up arrowhead indicates a port at the top. |
Meanings of service port indicators vary in different modes. For details, see Table 2-351. When a 40GE port is configured as four 10GE ports, this indicator shows the status of a 10GE port. The sequence number of the indicated 10GE port is identified by indicators 40GE Breakout 1/2/3/4 on the lower right corner of the panel. NOTE:
Each 40GE port has a single-color indicator, which shows the status of the 40GE port by default. If a 40GE port is not split and is connected to four 10GE ports on a remote device using a one-to-four high-speed cable, the 40GE port cannot go Up and its indicator is off. |
||
8 |
- |
40GE Breakout 1/2/3/4 (sequence number indicators of 10GE ports converted from a 40GE port) NOTE:
Indicators 1, 2, 3, 4 turn on in cyclic order, with each indicator keeping on for 5s. |
Green |
Off |
40GE ports are not split into four 10GE ports. |
Steady on |
At least one 40GE port has been split into four 10GE ports. When one or more 40GE ports are configured as four 10GE ports, these indicators identify the sequence numbers of the 10GE ports. A 40GE port indicator (7 in Figure 2-171) shows the status of a 10GE port converted from the 40GE port:
The following is an example: The first 40GE port shown in Figure 2-171 is split into four 10GE ports, and the second 40GE port is not split.
|
||||
9 |
ACT |
USB-based deployment indicator |
Green |
Off |
USB-based deployment is disabled (default state). |
Steady on |
USB-based deployment has been completed. |
||||
Blinking |
The system is reading data from a USB flash drive. |
||||
Red |
Steady on |
USB-based deployment has failed. |
|||
10 |
L/A |
ETH management port indicator |
Green |
Off |
No link is established on the port. |
Steady on |
A link is established on the port. |
||||
Blinking |
The port is sending or receiving data. |
Display Mode |
Port |
Color |
Description |
---|---|---|---|
STAT |
40GE optical port |
- |
Off: The port is not connected or has been shut down. |
Green |
|
||
SPEED |
40GE optical port |
- |
Off: The port is not connected or has been shut down. |
Green |
|
||
STACK |
Green NOTE:
This row describes the states and meanings of port indicators on a switch working in stack mode. |
NOTE:
In STACK mode, a 10GE optical port has only its LINK indicator on (green). |
|
Green NOTE:
This row describes the states and meanings of port indicators on a switch working in super virtual fabric (SVF) mode. |
|
Ports
10GE SFP+ Ethernet Optical Port
40GE/100GE QSFP28 Optical Port
Console Port
ETH Management Port (RJ45)
USB Port
A USB flash drive can be connected to the USB port for log backup, system software backup and uploading, or USB-based deployment.
Specifications
Table 2-356 lists technical specifications of the CE8850-32CQ-EI switch.
Item |
Description |
|
---|---|---|
Physical specifications |
|
|
Environment parameters |
Temperature |
|
Relative humidity |
5% RH to 95% RH, noncondensing |
|
Altitude |
< 5000 m (16404 ft.) |
|
Noise (sound pressure, 27°C) |
|
|
Power specifications |
Power source type |
AC |
AC power input |
|
|
DC power input |
|
|
High-voltage DC power input |
Not supported |
|
Rated input current |
|
|
Chassis power consumption |
Maximum power consumption |
453 W |
Typical power consumption |
219 W (100% throughput, SFP+ cables on 2 ports and QSFP28 cables on 32 ports, double power modules) |
|
Chassis heat dissipation |
Maximum heat dissipation |
1544 BTU/hr |
Typical heat dissipation |
748 BTU/hr (100% throughput, SFP+ cables on 2 ports and QSFP28 cables on 32 ports, double power modules) |
|
Surge protection |
Power module:
|
|
Heat dissipation |
Heat dissipation mode |
Air cooling |
Airflow |
Front-to-back or back-to-front, depending on the fan modules and power modules |
|
Reliability |
Power module backup |
1+1 backup |
Fan module backup |
1+1 backup not supported NOTE:
A CE8850EI chassis uses two fan modules, with each fan module containing two fans. The four fans in the chassis work in 3+1 backup mode. |
|
Hot swap |
Supported by all power modules and fan modules |
|
Mean time between failures (MTBF) |
45.34 years |
|
Mean time to repair (MTTR) |
1.68 hours |
|
Availability |
0.99999576496 |
|
Technical specifications |
Processor |
1.5 GHz, eight-core |
DRAM Memory |
4 GB |
|
NOR Flash |
32 MB |
|
NAND Flash |
1 GB |
|
Stack |
Service port supporting the stack function |
10GE optical ports and 100GE optical ports |
Certification |
|
Ordering Information
Ordering information is subject to change without notice in the case of product upgrades. Ordering information provided in this manual is for reference only. To obtain latest ordering information, contact Huawei switch distributors or local Huawei representative office.
Table 2-357 provides the ordering information.
Part Number |
Part Model |
Part Description |
---|---|---|
02350SQW |
CE8850-32CQ-EI |
CE8850-32CQ-EI Switch (32-Port 10GE QSFP28, 2-Port 10GE QSFP+, Without Fan and Power Module) |
02350SBC |
CE8850-EI-F-B0A |
CE8850-32CQ-EI Switch (32-Port 100GE QSFP28, 2-Port 10GE SFP+, 2*AC Power Module, 2*FAN Box, Port-side Exhaust) |
02350SBD |
CE8850-EI-B-B0A |
CE8850-32CQ-EI Switch (32-Port 100GE QSFP28, 2-Port 10GE SFP+, 2*AC Power Module, 2*FAN Box, Port-side Intake) |