CE88-D16Q (16-Port 40GE Interface Card (QSFP+))

CloudEngine 8800, 7800, 6800, and 5800 Series Switches Hardware Description (Versions earlier than V200R020C00)

This document provides an overall description of the CE5800&6800&7800&8800 series switches hardware that versions earlier than V200R020C00, helping you obtain detailed information about each chassis, power module, fan module, card, cable, and pluggable modules for ports.

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

CE88-D16Q (16-Port 40GE Interface Card (QSFP+))

Version Mapping

Table 5-9 describes the mapping between the CE88-D16Q card, switch models, and software versions.

Table 5-9 Version mapping

Switch Model	CE88-D16Q
CE7800, CE6800, and CE5800 series switches and the CE8850EI	Not supported
CE8860-4C-EI	Supported in V100R006C00 and later versions
CE8861-4C-EI CE8868-4C-EI	Supported in V200R005C10 and later versions NOTE: The registration and interface usage of the CE88-D16Q subcards on the CE8868EI are controlled by licenses. By default, the CE88-D8CQ and CE88-D16Q subcards on the CE8868EI are not enabled. To use these subcards on the CE8868EI, apply for and purchase the license from the equipment supplier. For the CE8868EI, after the above license is loaded, you need to run the active card-license command to enable the corresponding license in the specified subcard slot. The CE8868EI has four subcard slots. You can purchase licenses based on the number of required subcard slots.

Switch Model

CE88-D16Q

CE7800, CE6800, and CE5800 series switches and the CE8850EI

Not supported

CE8860-4C-EI

Supported in V100R006C00 and later versions

CE8861-4C-EI

CE8868-4C-EI

Supported in V200R005C10 and later versions

NOTE:

The registration and interface usage of the CE88-D16Q subcards on the CE8868EI are controlled by licenses. By default, the CE88-D8CQ and CE88-D16Q subcards on the CE8868EI are not enabled. To use these subcards on the CE8868EI, apply for and purchase the license from the equipment supplier.
For the CE8868EI, after the above license is loaded, you need to run the active card-license command to enable the corresponding license in the specified subcard slot. The CE8868EI has four subcard slots. You can purchase licenses based on the number of required subcard slots.

Card Overview

The CE88-D16Q card can be install in any slot of the CE8860-4C-EI, CE8861-4C-EI, or CE8868-4C-EI chassis.

Figure 5-5 shows the appearance of the CE88-D16Q card.

Figure 5-5 CE88-D16Q card

Functions and Features

Table 5-10 describes functions and features of the CE88-D16Q card.

Table 5-10 Functions and features

Function and Feature	Description
Basic function	Provides data packet processing and traffic management on 16 40GE QSFP+ optical ports.
Port split	Each QSFP+ optical port can be split into two 10GE ports. The two 10GE cannot work at 1 Gbit/s. With the port split function, each card can provide up to 32 10GE optical ports. NOTE: All the 40GE QSFP+ optical ports are independent, and each can be configured as two 10GE ports. For CE8861EI and CE8868EI, the two 40GE interfaces must be split simultaneously so that converted 10GE interfaces can work properly.
Hot swap	Supported
Service port stacking	Ports on the card can be used as stack ports.

Indicators and Ports

Figure 5-6 shows indicators on the CE88-D16Q panel.

Figure 5-6 Indicators on the CE88-D16Q panel

Table 5-11 describes indicators on the CE88-D16Q panel.

Table 5-11 Indicator description

Number	Indicator	Color	Status	Description
1	One single-color indicator for each interface NOTE: Arrowheads show the positions of ports. A down arrowhead indicates a port at the bottom, and an up arrowhead indicates a port at the top.	Green	Off	No link is established on the port.
			Steady on	A link has been established on the port.
			Blinking	The port is transmitting or receiving data.

Figure 5-7 shows the ports on the CE88-D16Q card.

Figure 5-7 Ports on the CE88-D16Q card

1. Sixteen 40GE QSFP+ optical ports

40GE QSFP+ optical port

Table 5-12 describes the attributes of a 40GE QSFP+ optical port.

Table 5-12 Attributes of a 40GE QSFP+ optical port

Attribute	Description
Connector type	Depends on the optical module used.
Optical attributes	Depends on the QSFP+ optical module used. See 40GE QSFP+ Optical Modules.
Applicable cables	When the port works in 40GE mode, it can use: QSFP+ optical module and MPO-MPO or LC-LC optical fiber QSFP+ to QSFP+ high-speed cable QSFP+ to QSFP+ AOC cable
Applicable cables	When the port works in 210GE mode, it can use: QSFP+ optical module and MPO-4DLC or MPO-8FC optical fiber (Among the four pairs of DLC or FC fibers, only the two pairs marked 1 and 2 can be used to connect to remote interfaces.) QSFP+ to 4SFP+ high-speed cable (Among the four SFP+ wires, only the two marked A and B can be used to connect to remote interfaces.) QSFP+ to 4*SFP+ AOC cable (Among the four SFP+ wires, only the two marked 1 and 2 can be used to connect to remote interfaces.)

Specifications

Table 5-13 lists technical specifications of the CE88-D16Q card.

Table 5-13 Technical specifications

Item	Description
Physical specifications	Dimensions (W x D x H): 210.0 mm x 205.2 mm x 41.8 mm (8.3 in. x 8.1 in. x 1.6 in.) Weight: 1.3 kg (2.87 lb) Typical power consumption: 27 W Maximum power consumption: 58 W Typical heat dissipation: 92 BTU/hr Maximum heat dissipation: 198 BTU/hr
Environment parameters	Operating temperature: 0°C to 40°C (32°F to 104°F) Relative humidity: 5% RH to 95% RH Storage temperature: -40°C to +70°C (-40°F to +158°F)

Ordering Information

Table 5-14 provides the ordering information.

Table 5-14 Ordering information

Part Number	Card Model	Card Description
03023CRR	CE88-D16Q	16-port 40GE interface card (QSFP+)

Translation

简体中文

Download

Updated: 2021-06-01

Document ID: EDOC1000019246

Downloads: 12398

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate