No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CX910 Switch Module V100R001C10 User Guide 15

This document describes the CX910 10GE switch module (CX910 for short) of the Tecal E9000 server in terms of its features, installation, removal, and configuration. This document applies to the CX910 whose 10GE switching planes use the software versions of 1.2.1.0.39, 2.00 and later.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Setting an IP Address for the Management Network Port

Setting an IP Address for the Management Network Port

Scenarios

The IP address of the management network port of the 10GE switching plane can be set locally or on the MM910 as follows:

Prerequisites

Data

Table 4-3 lists the data to be obtained before this operation.

Table 4-3 Required data

Name

Description

Example Value

IP address, subnet mask, and gateway of the 10GE switching plane management network port

You can log in to the 10GE switching plane CLI from a PC by using the IP address of the management network port.

  • IP address: 192.168.101.120
  • Subnet mask: 255.255.255.0
  • Gateway: 192.168.101.1

Table 4-4 lists the default data to be prepared.

Table 4-4 Default data

Name

Default Data

Description

Initial user name and password of the MM910

  • User name: root
  • Password: Huawei12#$

The default user of the MM910 OS has all OS rights.

Software

PuTTY.exe is free software. You can download it from the Internet. PuTTY 0.60 or later is required for login over a serial port.

Procedure

  1. Log in to the MM910 WebUI.

    For details, see Logging In to the HMM WebUI.

  2. On HMM Web, choose Chassis Settings.

    The Chassis Settings page is displayed.

  3. In the navigation tree on the left, choose Network Settings > Swi.
  4. Click Edit.

    Edit the IP addresses of management network ports of the 10GE switching plane in specific slots.

    Fabric indicates the 10GE switching plane.

  5. Click Deliver.

    The IP addresses of 10GE switching plane management network ports are successfully set.

  6. (Optional) Configure the switching plane gateway.

    1. Use an SSH connection tool to log in to the MM910 CLI by using the floating IP address of the MM910s.

      This topic describes how to use PuTTY to log in over SSH. For details, see Logging In to a Server Over a Network Port by Using PuTTY.

    2. Configure a gateway address for the Ethernet switching plane so that the switching plane can properly communicate with the PC.

      smmset -l swiN:fruM -d route -v targetvalue maskvalue gatewayvalue

      The parameters are described as follows:

      • N: specifies the slot number of a switch module. Its value ranges from 1 to 4, mapping to switch module slots 1E, 2X, 3X, and 4E respectively.
      • M: indicates the ID of a switching plane. The value of the 10GE switching plane is 2.
      • targetvalue: specifies the target network segment IP address of the switching plane.
      • maskvalue: specifies the subnet mask of the switching plane.
      • gatewayvalue: specifies the gateway IP address of the switching plane.

Translation
Download
Updated: 2018-09-20

Document ID: EDOC1000036339

Views: 11689

Downloads: 238

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next