No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CX913 Switch Module V100R001C10 User Guide 15

This document describes the CX913 10GE switch module (CX913 for short) of the Tecal E9000 server in terms of its features, installation, removal, and configuration. This document applies to the CX913 whose 10GE switching planes use the software versions of 1.2.1.0.39, 2.00 and later.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Installing the CX913

Installing the CX913

Scenarios

Install the CX913 in the E9000 chassis. Before the operation, become familiar with the hardware devices.

Impact on the System

This operation has no adverse impact on the system.

Prerequisites

Conditions

The chassis has been installed.

Data

Data preparation is not required for this operation.

Tools

The following tools are available:

  • Protective gloves
  • Electrostatic discharge (ESD) gloves
  • Phillips screwdriver (PH3 is 8 mm or 0.31 in.)

Workflow

Figure 3-1 Installation process

Procedure

  1. Determine the position for installing the CX913 in the chassis.

    Figure 3-2 Slot numbers

  2. Remove the switch module filler panel.

    1. Use a Phillips screwdriver to loosen the two M3 captive screws on the switch module filler panel. See (1) in Figure 3-3.
      Figure 3-3 Removing the switch module filler panel
    2. Raise the two handles on the switch module filler panel completely, and pull the filler panel horizontally out of the chassis. See (2) and (3) in Figure 3-3.
    3. Store the switch module filler panel for future use.

  3. Install the CX913.

    1. Raise the two ejector levers on the CX913 completely and push the CX913 horizontally into the chassis as far as it will go. See (1) and step (2) in Figure 3-4.
      Figure 3-4 Installing the CX913
    2. Lower the two ejector levers on the CX913 until the CX913 is completely inserted. See (3) in Figure 3-4.
    3. Use a Phillips screwdriver to tighten the two M3 captive screws on the CX913. See (4) in Figure 3-4.

  4. Determine the connection relationships between signal cables and ports on the CX913. Figure 3-5 shows the port types and numbers of the CX913.

    Figure 3-5 Port types and numbers

    1

    BMC serial port

    2

    SYS serial port

    3

    GE electrical port(reserved)

    4

    10GE optical port

    5

    8G FC optical port

    -

    -

  5. (Optional) Connect a serial cable.

    Figure 3-6 Connecting a serial cable
    NOTE:

    The BMC serial port, SYS serial port, are standard RJ-45 ports and are connected in the same way.

  6. Connect a 10GE or FC optical module and optical fiber.

    1. Determine the optical module type and the optical port to be connected depending on site requirements.
    2. Push the optical module into the optical port until the optical module is locked in place, as shown in Figure 3-7.
      Figure 3-7 Installing an optical module
    3. Remove the dust-proof cap from the optical fiber. See (1) in Figure 3-8.
      Figure 3-8 Connecting an optical fiber
      NOTE:

      Use the same method to connect an optical fiber to a 10GE optical port or 8G FC optical port.

    4. Insert the optical fiber into the optical module. See (2) in Figure 3-8.

  7. Check the indicator status after the CX913 is powered on.

    For details, see Table 2-6.

  8. Follow-up Procedure

    See section Configuring the CX913.

Translation
Download
Updated: 2018-09-20

Document ID: EDOC1000036345

Views: 13445

Downloads: 183

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next