No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Huawei Server Maintenance Manual 09

Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Logging In to the MM910 WebUI

Logging In to the MM910 WebUI

Scenarios

Log in to the MM910 WebUI by using a browser on the local PC to configure and manage the chassis, MM910s, compute nodes, storage nodes, switch modules, pass-through modules, power supply units (PSUs), and fan modules.

Impact on the System

This operation has no adverse impact on the system.

NOTE:
  • The user account will be locked if incorrect passwords are entered for five consecutive times. The user account will be automatically unlocked in 5 minutes, but cannot be forcibly unlocked. If you attempt to enter a password again within 5 minutes, the lock duration is reset to 5 minutes no matter whether the entered password is correct.
  • The WebUI of the standby MM910 (displayed as "This is the standby MM.") does not display component installation status. After logging in to the WebUI of the standby MM910, you can view the status of the active MM910 and perform the following operations for the standby MM910: Set the DHCP parameters and a static IP address, set and query the thresholds and hysteresis of threshold sensors, collect system operating information, and upgrade the management software. To perform other operations, log in to the WebUI of the active MM910.

Data

You have obtained the following data:

  • User name for logging in to the server to be connected. The default user name is root.
  • User password for logging in to the server to be connected. The default user password is Huawei12#$.

Procedure

  1. Connect the Ethernet port on the local PC to the MGMT ports on the active and standby MM910s over the local area network (LAN).

    If you want to connect your local PC directly to the MM910 using a network cable but the MGMT port on the active MM910 is already connected with a network cable, do not remove the network cable from the MGMT port on the active MM910. Otherwise, an active/standby switchover of the MM910s will be triggered, which may cause network interruption. You can connect the network cable from the local PC to the STACK port of the active MM910 in the chassis. If the STACK port on the active MM910 is also used, connect the network cable to an idle STACK port on an active MM910 in a chassis cascaded with the E9000 chassis.

    Figure 3-30 shows the network connections.

    Figure 3-30 Network connections
    NOTE:
    • For MM910 V2.25 or earlier, the port on the switch module in slot 2X or 3X is used as the default management network port for connecting to an external network. In this situation, do not connect the MGMT port on the MM910 and the port on the switch module to the same network simultaneously. Connecting these ports simultaneously will cause a network storm.

      To use the MGMT port on the MM910 panel as the management network port for connecting to an external network, run the smmset -d outportmode -v 1 command on the CLI.

    • For MM910 V2.26 or later, the MGMT port on the MM910 panel is used as the default management network port for connecting to an external network.

  2. Set the IP address and subnet mask or route information for the local PC so that the local PC can communicate with the MM910 properly.
  3. On the menu bar of Internet Explorer, choose Tools > Internet Options.

    The Internet Options dialog box is displayed.

    NOTE:

    This section uses a PC running Windows 7 and Internet Explorer 8.0 as an example.

  4. Click the Connections tab and click LAN Settings.

    The LAN Settings dialog box is displayed.

  5. In the Proxy server area, deselect the Use a proxy server for your LAN check box.
  6. Click Yes.

    The LAN Settings dialog box closes.

  7. Click Yes.

    The Internet Options dialog box closes.

  8. Open Internet Explorer, enter https://MM910 floating IP address in the address box, and press Enter.

    For example, enter https://10.85.4.77 in the address box.

    "There is a problem with this website's security certificate" is displayed.

  9. Click Continue to this website (not recommended).

    The page for logging in to the HMM WebUI is displayed.

  10. Set the parameters. See Figure 3-31 and Figure 3-32.

    • Language: Select English.
    • User name: Enter the user name for login. The default user name is root.
    • Password: Enter the user password for login. The default password is Huawei12#$.
    • Login To: Select This Machine/computer in most cases. Select LDAP if the system manages domain users by using an active directory (AD) server.
    Figure 3-31 Logging in to the HMM WebUI (MM910 (U54) 2.20 or later)

    Figure 3-32 Logging in to the HMM WebUI (MM910 earlier than (U54) 2.20)

  11. Click Log In.

    The HMM WebUI is displayed, as shown in Figure 3-33 or Figure 3-34.

    Figure 3-33 HMM WebUI (MM910 (U54) 2.20 or later)

    Figure 3-34 HMM WebUI (MM910 earlier than (U54) 2.20)

Translation
Download
Updated: 2019-02-25

Document ID: EDOC1000041338

Views: 71626

Downloads: 3788

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next