No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CX11x, CX31x, CX710 (Earlier Than V6.03), and CX91x Series Switch Modules V100R001C10 Configuration Guide 12

The documents describe the configuration of various services supported by the CX11x&CX31x&CX91x series switch modules The description covers configuration examples and function configurations.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuration Examples

Configuration Examples

This section describes configuration examples of loopback detection including networking requirements, configuration roadmap, and configuration procedure.

Example for Configuring Loopback Detection

Networking Requirements

As shown in Figure 5-122, if there is a loop on the network connected to the 10GE1/17/1 interface, broadcast storms will occur on the Switch Module or even the entire network.

To detect loops on the network connected to the switch and disabled downlink interfaces to reduce impacts on the switch and other networks, enable loopback detection on the Switch Module.

Figure 5-122 Loopback detection network diagram
Configuration Roadmap

The configuration roadmap is as follows:

  1. Enable loopback detection on the interface to detect loops on downlink networks.
  2. Specify the VLAN ID for loopback detection packets.
  3. Set loopback detection parameters to enable the interface automatic recovery.

Procedure

  1. Enable loopback detection on the interface.

    <HUAWEI> system-view
    [~HUAWEI] sysname Switch
    [*HUAWEI] commit
    [~Switch] interface 10ge 1/17/1
    [~Switch-10GE1/17/1] loopback-detect enable
    [*Switch-10GE1/17/1] commit
    [~Switch-10GE1/17/1] quit

  2. Specify the VLAN ID for loopback detection packets.

    [~Switch] vlan 100
    [*Switch-vlan100] quit
    [*Switch] interface 10ge 1/17/1
    [*Switch-10GE1/17/1] port link-type trunk
    [*Switch-10GE1/17/1] port trunk allow-pass vlan 100
    [*Switch-10GE1/17/1] loopback-detect vlan 100
    [*Switch-10GE1/17/1] commit
    [~Switch-10GE1/17/1] quit

  3. Set loopback detection parameters.

    # Configure the action the interface when a loopback is detected.

    [~Switch] loopback-detect action error-down
    [*Switch] commit

    # Set the interval between sending loopback detection packets.

    [~Switch] loopback-detect transmit interval 10
    [*Switch] commit

  4. Check the configuration.

    Run the display loopback-detect command to check the configuration.

    <~Switch> display loopback-detect 
    ------------------------------------------------------------                                                                        
     Loopback-detect transmit interval: 10s                                                                                             
    ------------------------------------------------------------                                                                        
    ------------------------------------------------------------                                                                        
    Interface                Action                   Status                                                                            
    ------------------------------------------------------------                                                                        
    10GE1/17/1                Error-Down               ErrorDown

Configuration Files

Configuration file of the Switch

#
sysname Switch
#
loopback-detect transmit interval 10
loopback-detect action error-down
#
vlan batch 100
#
interface 10GE1/17/1
 port link-type trunk
 port trunk allow-pass vlan 100
 loopback-detect enable
 loopback-detect vlan 100
#
return
Translation
Download
Updated: 2019-08-09

Document ID: EDOC1000041694

Views: 57501

Downloads: 3619

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next