No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CX11x, CX31x, CX710 (Earlier Than V6.03), and CX91x Series Switch Modules V100R001C10 Configuration Guide 12

The documents describe the configuration of various services supported by the CX11x&CX31x&CX91x series switch modules The description covers configuration examples and function configurations.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Maintaining Multicast Routes (IPv6)

Maintaining Multicast Routes (IPv6)

You can monitor IPv6 multicast routing and forwarding, and configuring the maximum number of invalid IPv6 multicast protocol packets that a device can store.

Monitoring IPv6 Multicast Routing and Forwarding

Context

During routine maintenance, run the following commands in any view to check the running status of the IPv6 multicast forwarding and routing table.

Procedure

  • Run the display multicast ipv6 boundary [ ipv6-group-address [ ipv6-group-mask-length ] ] [ interface interface-type interface-number ] command to check information about the IPv6 multicast boundary configured on an interface.
  • Run the display multicast ipv6 fib [ source ipv6-source-address | group ipv6-group-address | incoming-interface { interface-type interface-number | register } ] * command to check the IPv6 multicast forwarding table.
  • Run the display multicast ipv6 routing-table [ ipv6-source-address [ mask ipv6-source-mask-length ] | ipv6-group-address [ mask ipv6-group-mask-length ] | incoming-interface { interface-type interface-number | register } | outgoing-interface { { exclude | include | match } { interface-type interface-number | register | none } } ] * [ outgoing-interface-number [ number ] ] command to check the IPv6 multicast routing table.
  • Run the display multicast ipv6 rpf-info ipv6-source-address [ ipv6-group-address ] [ rpt | spt ] [ verbose ] command to check the Reverse Path Forwarding (RPF) route.

Configuring the Maximum Number of Invalid IPv6 Multicast Protocol Packets that a Device Can Store

Context

If multicast forwarding entries cannot be established on a network, you can configure the maximum number of invalid IPv6 multicast protocol packets that the devices can store. Then you can check statistics and detailed information about invalid multicast protocol packets using related commands to troubleshoot problems.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    multicast ipv6 invalid-packet { mld | pim } max-count max-number

    The maximum number of invalid IPv6 multicast protocol packets that the device can store is configured.

    By default, a device can store a maximum of 10 invalid IPv6 packets for each multicast protocol.

  3. Run:

    commit

    The configuration is committed.

Checking the Configuration

To check statistics about invalid IPv6 multicast protocol packets that the device stores, perform the following operations:

  • Run the display mld invalid-packet [ interface interface-type interface-number | message-type { done | query | report } ] * command to check statistics about invalid multicast listener discovery (MLD) packets that the device stores.
  • Run the display mld invalid-packet [ packet-number ] verbose command to check details about invalid MLD packets that the device stores.
  • Run the following commands in any view to check statistics about invalid IPv6 Protocol Independent Multicast (PIM) packets that the device stores.
    • display pim ipv6 invalid-packet [ interface interface-type interface-number | message-type { assert | bsr | hello | join-prune } ] *
    • display pim ipv6 invalid-packet message-type { crp | register | register-stop }
  • Run the display pim ipv6 invalid-packet [ packet-number ] verbose command to check details about invalid IPv6 PIM packets that the device stores.
Translation
Download
Updated: 2019-08-09

Document ID: EDOC1000041694

Views: 57213

Downloads: 3617

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next