No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CX11x, CX31x, CX710 (Earlier Than V6.03), and CX91x Series Switch Modules V100R001C10 Configuration Guide 12

The documents describe the configuration of various services supported by the CX11x&CX31x&CX91x series switch modules The description covers configuration examples and function configurations.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Multicast Network Management Functions

Configuring Multicast Network Management Functions

You can enable the alarm function for a specified module to monitor events of the specified protocol.

Pre-configuration Tasks

Before configuring multicast network management, complete the following tasks:
  • Configure basic multicast functions to ensure normal multicast transmission on the network
  • Configure basic SNMP functions to ensure normal communication with the NMS by running SNMP

Configuration Process

Perform configuration tasks in the sequence listed as follows.

Enabling Multicast Network Management

Context

Before configuring basic functions of multicast network management, enable multicast network management. Do as follows on the switch modules managed by the NMS:

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    multicast mib

    The multicast MIB view is displayed and multicast network management is enabled.

    After this function is enabled, multicast MIB is bound to the public network instance.

  3. Run:

    commit

    The configuration is committed.

Enabling the Trap Function for a Specified Module

Context

You can enable the trap function for a specified module to monitor events of the specified protocol. Perform the following steps on the switch modules that needs to be managed by the NMS.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. You can choose one or multiple operations to perform:

    • Run the snmp-agent trap enable feature-name msdp [ trap-name { establish | backward } ] command to enable the MSDP trap function.

      By default, the MSDP trap function is disabled.

    • Run the snmp-agent trap enable feature-name pim [ trap-name { interface-election | invalid-join-prune | invalid-register | neighbor-loss | new-neighbor | rp-mapping-change } ] command to enable the trap function for PIM.

      By default, the trap function is disabled for PIM.

    • Run the snmp-agent trap enable feature-name pim-std [ trap-name { pimneighborloss | piminvalidregister | piminvalidjoinprune | pimrpmappingchange | piminterfaceelection } ] command to enable the public PIM trap function.

      By default, the public PIM trap function is disabled.

  3. Run:

    commit

    The configuration is committed.

(Optional) Adjusting the Interval for PIM to Send Trap Messages

Context

After PIM is enabled on the switch moduleses, you can configure PIM-MIB notifications to set the interval for sending PIM events. Therefore, you can know the current status of various PIM events on the switch moduleses in real time. The PIM events include the neighbor loss event, neighbor addition, the event of receiving invalid Join/Prune messages, RP-mapping change event, event of the interface being elected as the DR and the event of receiving invalid Register messages.

Do as follows on the switch modules managed by the NMS:

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    multicast mib

    The multicast MIB view is displayed.

  3. Run:

    pim mib-notification interval { interface-election-dr election-value | invalid-join-prune jp-value | invalid-register register-value | neighbor-loss loss-value | new-neighbor new-value | rp-mapping-change change-value }

    The interval for PIM to send trap messages is set.

    By default, the interval for sending trap messages for neighbor lost and neighbor addition is 0 seconds. That is, once the event occurs, PIM reports it immediately.

    The default interval for sending the trap of event of receiving invalid Join/Prune messages, the RP-mapping change event, the event of the interface being elected as the DR or the event of receiving invalid Register messages is 65535 seconds. After the events of these types occur, PIM does not report them.

    NOTE:

    To configure PIM to report these events, you can run the pim mib-notification interval command to set an interval smaller than 65535 seconds.

  4. Run:

    commit

    The configuration is committed.

Checking the Configuration

Procedure

  • Run the display snmp-agent trap feature-name msdp all command to check the status of the MSDP trap function.
  • Run the display snmp-agent trap feature-name pim all command to check the status of the PIM trap function.
  • Run the display snmp-agent trap feature-name pim-std all command to check the status of the public PIM trap function.
Translation
Download
Updated: 2019-08-09

Document ID: EDOC1000041694

Views: 58130

Downloads: 3621

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next