No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

OceanStor 9000 V100R001C01 Parts Replacement 12

Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Adding Memory Modules

Adding Memory Modules

This section explains how to add memory modules for a Mini-capacity node.

Impact on the System

You must power off the Mini-capacity node before adding memory modules. This interrupts the services running on the Mini-capacity node. Exercise caution when performing this operation.

Prerequisites

  • The system version is V100R001C30SPC100 or later versions.
  • The replacement memory module is ready.
  • The faulty memory module has been located.
  • The memory module is located at the rear of the main control board enclosure. You need to remove the cover and air director from the main control board enclosure before replacing the memory module.
  • Before replacing the memory module, use KVM to log in to the OS as user root (default password is Root@storage), then run poweroff to poweroff the node and wait for the shutdown to complete. Wait for the KVM screen to have no output, indicates that the shutdown has been completed. Label the cables on the node and disconnect the node from the power sockets and other devices. Use KVM to run poweroff need to be done on every node in the system.

Precaution

  • Only qualified technical support engineers are allowed to replace a memory module.
  • Ensure that both power supplies of the Mini-capacity node have been shut down.
  • The memory module has one installation direction only. Use even force when you insert a memory module into the slot. Excessive force may damage the memory module or slot.
  • The adding memory modules must be the same as the other memory modules. If new memory modules are different from the old memory modules, it is recommended to change all old memory modules in the node.
  • It is recommended to add same capacity memory modules in same type of nodes. If memory capacity in same type of nodes is different, it could cause faulty due to unbalanced performance between nodes.
  • Before adding a memory module, record the system memory capacity for check and comparison after the replacement.
  • Follow different specific regulations when you insert different number of memory modules. The red box in Figure 2-32 shows the memory slot on the mainboard. Table 2-2 shows memory configuration and installation list.
    Figure 2-32  Location of memory slots

    Table 2-2  Memory configuration and installation

    Number of Memory Modules

    Memory Slot No.

    1+1

    NVDIMM: F0

    DIMM: A0

    1+2

    NVDIMM: F0

    DIMM: A0, D0

    1+3

    NVDIMM: F0

    DIMM: A0, B0, D0

    1+4

    NVDIMM: F0

    DIMM: A0, B0, D0, E0

    1+5

    NVDIMM: F0

    DIMM: A0, B0, C0, D0, E0

    1+6

    NVDIMM: F0

    DIMM: A0, A1, B0, B1, D0, E0

    1+7

    NVDIMM: F0

    DIMM: A0, A1, B0, B1, C0, D0, E0

    1+8

    NVDIMM: F0

    DIMM: A0, A1, B0, B1, D0, D1, E0, E1

    1+9

    NVDIMM: F0

    DIMM: A0, A1, B0, B1, C0, D0, D1, E0, E1

    1+10

    NVDIMM: F0

    DIMM: A0, A1, B0, B1, C0, C1, D0, D1, E0, E1

Tools and Materials

  • Phillips screwdriver
  • ESD gloves
  • ESD wrist strap
  • ESD bag
  • Labels

Procedure

  1. Wear the ESD wrist strap and ESD gloves. For details, see Put on an ESD wrist strap in Replacing a Main Control Board Enclosure.
  2. Use KVM to log in to the OS as user root (default password is Root@storage), then run poweroff to poweroff the node and wait for the shutdown to complete.

    Wait for the KVM screen to have no output, indicates that the shutdown has been completed.

  3. Label the cable connections between the Mini-capacity node and power sockets and peripheral devices. Then disconnect the cables.
  4. Pull out the main control board enclosure. For details, see 4 in Replacing a Fan Module.
  5. Remove the cover of the main control board enclosure. For details, see 5 in Replacing a Fan Module.
  6. Take out the air director upward.
  7. Open memory ejectors to enable the memory module to disconnect from the slot, as shown in step 1 in Figure 2-33.
  8. Take out the memory module upward from the chassis, as shown in step 2 in Figure 2-33.

    Figure 2-33  Removing a memory module

  9. Put the removed memory module into an ESD bag.
  10. Take the replacement memory module out of its ESD bag.
  11. Align the notch on the memory module with that on the slot and then insert the memory module into the slot, as shown in step 1 in Figure 2-34.
  12. Close the memory ejectors, as shown in step 2 in Figure 2-34. Then the ejectors automatically lock the memory module.

    Figure 2-34  Installing a memory module

  13. Align the notches in the enclosure and install the air director.
  14. Install the cover of the main control board enclosure. For details, see 10 in Replacing a Fan Module.
  15. Install the main control board enclosure. For details, see 11 in Replacing a Fan Module.

    After hardware installation, if there are operations need to be performed using BIOS, for the initial startup, clear NVDIMM data using the BIOS. Otherwise, the operating system may fail to be started. Before connecting the power cable and powering on the storage node, connect the KVM cable, and then adjust the display content of the KVM to the port connected to the storage node.

  16. Correctly connect the Mini-capacity node to the power sockets and peripheral devices according to the cable connection labels. Then power on the Mini-capacity node.
  17. Clear NVDIMM data.
    1. During the system startup process, hold down F2 or press Esc when the Press Esc for boot options message is displayed, choose SCU, input the BIOS password to enter the BIOS screen.
    2. Choose Security > Clear NvDimm Flash.

      Figure 2-35  Choosing Clear NvDimm Flash

    3. In the Clear NvDimm Flash? dialog box, select Yes and press Enter.

      Figure 2-36  Starting to clear NVDIMM data

    4. Wait 20 seconds. Check whether the displayed dialog box states "Clear NvDimm flash success. Please reboot system!"

      • If yes, go to 17.e.
      • If no, contact technical support.
      Figure 2-37  Clearing NVDIMM data

    5. Press Enter and then F10. In the dialog box that is displayed, select Yes to save the configuration and restart the storage node.

      Figure 2-38  Saving the configuration and restarting the storage node

  18. Restart the system. During the startup, enter the BIOS interface to check the system memory capacity.

    Depending on the BIOS software version, the optional operations are as follows:
    • During the system startup, press and hold down F2, input the BIOS password to enter the BIOS. Check the system memory capacity, as shown in Figure 2-39.
      Figure 2-39  Check the system memory capacity

    • When the information as shown in Figure 2-40 is displayed, press Esc, choose SCU when the window display as shown in Figure 2-41, input the BIOS password to enter the BIOS screen.
      Figure 2-40  Press Esc

      Figure 2-41  Choose SCU

    • If the system memory capacity equals the actual memory capacity, the installation is successful.
    • If the system memory capacity is smaller than the actual memory capacity or the system cannot start correctly, the memory module may be incorrectly installed. In this case, reinstall the memory module.

  19. Repeat 2 to 18 on nodes that to be adding memory modules.
  20. Restart nodes added memory modules and power on the other nodes in the system.
  21. Wait for about 10 minutes then log in to DeviceManager, click Alarms, check if there are any major alarms or more critical ones.

    • If yes, rectify the fault according to suggestion.
    • If no, no further operations are required.

Follow-up Procedure

After the memory module is replaced, label the replaced memory module to facilitate subsequent operations.

Download
Updated: 2018-10-27

Document ID: EDOC1000042171

Views: 15627

Downloads: 121

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next