No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 Series Agile Switches Hardware Description

This document describes hardware components of the S12700, including the cabinet, chassis, power supply facilities, fan modules, cards, cables, and pluggable modules for interfaces. You can find useful information about S12700 hardware components from this document.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ET1D2S04SX5E-4-port 10GE SFP+ and 44-port GE SFP interface card (X5E, SFP+)

ET1D2S04SX5E-4-port 10GE SFP+ and 44-port GE SFP interface card (X5E, SFP+)

Version Mapping

Table 7-216 Switch chassis and software versions matching the card

Card Name

S12700 Chassis

ET1D2S04SX5E

Supported in V200R013C00 and later versions

Introduction

The ET1D2S04SX5E can be installed in:

  • Slots 01 to 04 in an S12704 chassis.
  • Slots 01 to 08 in an S12708 chassis.
  • Slots 01 to 10 in an S12710 chassis.
  • Slots 01 to 12 in an S12712 chassis.
Figure 7-104 Appearance of the ET1D2S04SX5E

Functions

The ET1D2S04SX5E provides the following functions:
  • Communicates with the MPU and works under the control of the MPU.
  • Searches for routes and destination addresses of data packets for forwarding.
  • Forwards data packets.
Table 7-217 Functions of the ET1D2S04SX5E
Function Description

Basic functions

Provides four 10GE optical ports and forty-four GE optical ports for data transmission and switching.

Distributed forwarding

Performs concurrent data forwarding using a distributed data plane.

Hot swapping

The ET1D2S04SX5E is hot swappable.

Indicators and Ports

Figure 7-105 Indicators on the ET1D2S04SX5E panel

Table 7-218 Indicators on the ET1D2S04SX5E panel

Number

Indicator

Color

Description

1

ACT indicator of a lower optical port

Yellow

Blinking: The port is transmitting and receiving data.

2

ACT indicator of an upper optical port

3

LINK indicator of a lower optical port

Green

Steady on: A link has been established on the port.

4

LINK indicator of an upper optical port

5

RUN/ALM: running status indicator

Green

Steady on: The card has been powered on, but the software is not running.

Slow blinking: The card software is running properly.

Fast blinking: The card software is starting.

Red

Steady on: The card has failed and the fault requires manual intervention.

Yellow

Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.)

Figure 7-106 Ports on the ET1D2S04SX5E panel

1 Four 10GBASE SFP+/1000BASE-X ports
2 Forty-four 1000BASE-X ports
10GBASE SFP+/1000BASE-X port

10GBASE SFP+/1000BASE-X ports support 10GE and GE auto sensing. Table 7-219 describes the attributes of a port working in 1000M mode, and Table 7-220 describes the attributes of a port working in 10G mode. Table 7-221 describes the attributes of a 10GBASE SFP+/1000BASE-X port using a copper module.

Table 7-219 Optical port attributes (GE optical module)
Attribute Description
Connector type SFP+
Optical port attributes

Depend on the SFP optical module used.

For the optical modules supported by the ET1D2S04SX5E and their attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules.
Standards compliance IEEE802.3z
Frame format Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol IP
Table 7-220 Optical port attributes (10GE optical module, high-speed cable or SFP+ optical cable)
Attribute Description
Connector type SFP+
Optical port attributes

Depend on the SFP+ - SFP+ high-speed cable (1 m, 3 m, 5 m, 10 m), QSFP+ - 4*SFP+ high-speed cable (1 m, 3 m, 5 m), SFP+ optical module, or SFP+ optical cable used.

For the optical modules supported by the ET1D2S04SX5E and their attributes, see 10GE SFP+ Optical Modules (OSXD22N00 not supported), 10GE-CWDM SFP+ Optical Modules, and 10GE-DWDM SFP+ Optical Modules.
Standards compliance IEEE 802.3ae
Frame format Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol IP
Table 7-221 Optical port attributes (copper module)
Attribute Description
Connector type SFP
Optical port attributes

Depend on the SFP copper module used.

For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (100 Mbit/s and 1000 Mbit/s rates).

Standards compliance IEEE 802.3ab
Frame format Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol IP
1000BASE-X ports

Table 7-222 lists the attributes of a 1000BASE-X port with an optical module installed.

Table 7-222 Optical port attributes (optical module)
Attribute Description
Connector type SFP
Optical port attributes

Depend on the SFP optical module used.

For details about optical modules supported by the ET1D2S04SX5E and its attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules.

Standards compliance IEEE 802.3z
Frame format Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol IP

Table 7-223 lists the attributes of a 1000BASE-X port with a copper module installed.

Table 7-223 Optical port attributes (copper module)
Attribute Description
Connector type SFP
Optical port attributes

Depend on the SFP copper module used.

For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (100 Mbit/s and 1000 Mbit/s rates).

Standards compliance IEEE 802.3ab
Frame format Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol IP

Specifications

Table 7-224 Specifications of the ET1D2S04SX5E

Item

Description

Physical specifications

  • Dimensions (H x W x D): 35.1 mm x 394.7 mm x 426.8 mm (1.38 in. x 15.54 in. x 16.80 in.)
  • Weight: 3.1 kg (6.83 lb)
  • Maximum power consumption: 124 W

Environment specifications

  • Operating temperature: 0°C to 45°C (32°F to 113°F)
  • Operating relative humidity: 5% RH to 95% RH (noncondensing)
  • Storage temperature: -40°C to +70°C (-40°F to +158°F)
  • Storage relative humidity: 5% RH to 95% RH (noncondensing)

Ordering Information

Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 7-225 Ordering information
Part Number Card Name Card Model
03032YEA

4-port 10GE SFP+ and 44-port GE SFP interface card (X5E, SFP+)

ET1D2S04SX5E
Translation
Download
Updated: 2019-08-19

Document ID: EDOC1000047496

Views: 183910

Downloads: 1907

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next