No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S1720, S2700, S3700, S5700, S6700, S7700, and S9700 Series Switches Common Operation Guide

This document describes the CLI-based configurations of universal protocols and common features for Huawei switches on basic networks.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Displaying Stack Configuration

Displaying Stack Configuration

NOTE:

If the switch does not support the stacking function, the following commands cannot be executed on the switch.

Stack configuration is not recorded in the configuration file and cannot be displayed using the display current-configuration command.

# Run the display stack command to check stack information.
<HUAWEI> display stack
Stack mode: Service-port                                                      
Stack topology type: Link                                                       
Stack system MAC: 0000-1382-4569                                                
MAC switch delay time: 10 min                                                    
Stack reserved VLAN: 4093                                                       
Slot of the active management port: 0
Slot    Role        MAC address       Priority   Device type
-------------------------------------------------------------
    0   Master      0018-82b1-6eb4   200          
    1   Standby     0018-82b1-6eba   150          
# Run the display stack configuration or display stack current-configuration command to check stack configuration. The following example uses V200R012C00.
<HUAWEI> display stack configuration
*    : Invalid-configuration                                                                                                        
#    : Unsaved configuration                                                                                                  
---------------Configuration on slot 1 Begin---------------                                                                                                                                                                                
stack enable                                                                                                                        
stack slot 0 renumber 2                                                                                                             
stack slot 2 priority 150                                                                                                           
stack reserved-vlan 4093                                                                                                            
stack timer mac-address switch-delay 10                                                                                             
                                                                                                                                    
interface stack-port 1/1                                                                                                            
 *port interface XGigabitEthernet1/0/1 enable
                                                                                                                                   
interface stack-port 1/2                                                                                                            
 #port interface XGigabitEthernet1/0/4 enable                                                                                       
---------------Configuration on slot 1 End-----------------  
  • If a stack member port is marked with an asterisk (*), the current configuration does not take effect. The possible causes are as follows:
    • The current configuration is ineffective.
    • The stack member port is located on a subcard that is not available.
  • If a stack member port is marked with a number sign (#), the current configuration is automatically generated after dedicated stack cables are connected but not saved to the flash memory using the save stack configuration or save command.
# Run the display stack port command to check the stack port configuration. The following example uses V200R012C00 service port stacking.
<HUAWEI> display stack port
*down : administratively down                                                                                                       
(r)   : Runts trigger error down                                                                                                    
(c)   : CRC trigger error down                                                                                                      
(l)   : Link-flapping trigger error down                                                                                            
(m)   : Media mismatch trigger error down                                                                                           
Logic Port         Phy Port                     Online       Status                                                                 
----------------------------------------------------------------------------                                                        
stack-port0/1      XGigabitEthernet0/0/1        present      down 
Translation
Download
Updated: 2018-09-03

Document ID: EDOC1000057410

Views: 84413

Downloads: 12103

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next